We have 2 CSACS 1121 with Cisco ACS 5.2.0.26.10 The primary server manages 20000+ authentications per day. Its memory utilization increases everyday. It is now at 83% , there a limit?,What will happen when memory utilization reach this limit?,What can we do to purge memory utilization? (reboot, service restart.
View 11 RepliesIs it possible to have Dual NIC on ACS v5.2 such as teaming or any else??
I am thinking of connecting the two NIC on the CSACS-1121-K9 appliance to two switches on the same network, but wondering if it will be possible or not.
We upgraded a CSACS-1121 from ACS 5.2 to ACS 5.4 with CLI Application upgrade ACS_5.4.0.46.0a.tar.gz FTP After ACS reboot, services never start... After 15 hours, we always get same message:
ACS/admin# show application status acs
Application initializing...
Status is not yet available.
Please check again in a minute.
We installed patch 5-4-0-46-2.tar.gpg but we got same issue for 2 hours ...What could I do?
Is it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies View RelatedI have a problem upgrading an appliance CSACS 1121 from version 5.1 to 5.2 because restore DVD has image of 5.1 not 5.2 and in cisco.com appears only two files 5.2-0-26-1.tar.gpg and ACS_v5.2.0.26.iso, the first image is a patch and the second I'm not sure if is image for version 5.2, in case if appropriate which would be the correct commands to perform the upgrade using CLI.
View 4 Replies View RelatedI cannot import certificate from CA (Certificate Authority). When I attempt to install the certificate to CSACS SE 4.2, the following error occurs during installation: "Unsupported private key file format".
View 7 Replies View RelatedI have an ACS applicance that had a version 5.1 and i did an upgrade to 5.3 with latest patch.For some reason, the runtime process got stuck in (reinitializing and restarting) state.i did the recommended action to perform ACS stop and ACS start and even hard reset of the appliance, but it did not cut itThis process turned out to be a bug and it should have been fixed in version 5.3, but it has not i guess
i know that acs reset-config will solve the issue, but i have a problem here , the license file will be deleted as well with the config and i cannot find a way to export the license and then import it into the reseted config ACS hardware. Unfortunately, the license file is not saved anywhere in the company and i cannot affort to lose it.how to export the license from the applicance (CSACS-1120)?
Does the new UCS hardware change anything ?Can we bundle 2 NICs somehow to get interface redundancy ?If still not possible to configure that in ACS 5 itself:Can it enentually be done on the "hardware" level within the appliance firmware (UCS BIOS) ?(RHEL would provide NIC bonding,,, unfortunately its not accessable from ACS5 CLI)
View 6 Replies View RelatedI'm trying to join a band new CSACS-1120 to our active directory without success. The process in it self should be pretty straigh forward, but so far no luck.
I've configured the relevant info under "Users and Identity Stores > External Identity Stores > Active Directory.
Active Directory Domain Name: xxx.com
Username/Password : domain administrator account
When I test connection I get a info dialog "This machine is currently connected to domain xxx.com".After which I try to save changes which gives a reply ""This System Failure occurred: {0}. Your changes have not been saved. Click OK to return to the list page."
I've noticed that in the system log "show logging system tail" that I get a exception as soon as I enter the AD configuration page and subsequently every time I perform a action on that section.
Why the AD join keeps on failing and what the debug exception I'm getting means?
What causes LMS 4.1 to have high memory utilization?
View 4 Replies View RelatedI've deployed many Cisco PIX 501 v6.3.3 either as normal firewalling feature and/or with VPN features enabled. I noticed in all my deployments, regardless if it's during peak hours or after office hours, the memory utilization is always consistent 11MB utilized over the total of 16MB(memory default size).
View 3 Replies View RelatedCisco 3845 router (256RAM / 64Flash), increases the cpu utilization upto 70~80 percent, during the time of high utilization, I am unable to run show command on router.The configuration is simple, this is connected with two internet links (24Mbps and 8Mbps) and its about 600~700 users are using internet.show version, show memory and show process cpu outputs are attached here.
View 7 Replies View RelatedI was looking at my CISCO ASA 5520 and i found something really strange
ciscoasa/VPN-context# sh mem detail
Used memory: 4259249568 bytes (793%)
------------- ----------------
Total memory: 536870912 bytes (100%)
but when I look at the system context this is what I see
ciscoasa# sh mem
Free memory: 170829000 bytes (32%)
Used memory: 366041912 bytes (68%)
------------- ----------------
Total memory: 536870912 bytes (100%)
As far as I know the ASA is working good.
Info of the device
Hardware: ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Just want to check with you about memory utilization on the Asa 5510 ..
Free memory: 19%
Used Memory: 81%
Is this normal? Because we hade a problem this morning and the memory was at 100%..
Device Manager version 6.1(5) 57
Hardware: ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
We have a Cisco SA520 Router (Firmware 2.1.18)We are only using this for about 1 month now. Router seems ok its justI am worried about the Memory utilization which reach to 62% (144/234 MB)Is this something to worry about?How can I utilize this by lowering down the usage?
View 3 Replies View RelatedWe have a 7206 router which acts as a MPLS Hub router for around 100+ remote locations. Bandwidh at mpls hub(terminated on this router) is 50 Mbps.
We have noticed that Memory utilization in this router gradually increases and when it reaches 100% this router hangs. It happence in frequesncy of 10 days and we have to restart the router when memory is 100%.
CPU utilization is normal i.e below 20%, WAN bandwidth will never cross 30mbps.
We are running OSPF on this router
We had two PIXes in our environment and working as a active-failover mode. Its noted in now a days the active PIX memory utilization is 98% and for standby PIX it is 96%. And also in some times we were experiencing packet loss to the ip of active PIX and which reflects in the inside servers access also. During that time the active pix was not accessible via ssh as well as ASDM. We have tried reloading the PIX and changing failover state of the PIX, but it results only a temporary solution. Current memory installed is 128 MB (maximum upgraded), so a upgrade is also not possible. Please see the show command outputs from the PIX. Current Software version is 7.2(4)
sh memory output (PIX 1 - active)
Free memory: 4850944 bytes ( 4%)
Used memory: 129366784 bytes (96%)
[code]....
1) How we can pin point the root cause of this high memory utilization?
2) What might be the reason for the high memory utilization for the standby pix (96%), still the PIX is in idle state?
3) Is it a hardware issue or a memory leak issue, then how can we find out?
4) Is a software upgrade to new version resolves the memory issue?
We have one Catalyst 6506 ( with WS-SUP720-3B, IOS is 12.2(18)SXF14 ) and one Catalyst 6509 ( with WS-SUP720-3B, IOS is 12.2(18)SXF17a ). We used WhatsUP to collect I/O & process memory utilization for both switches. The memory utilization for Catalyst 6509 was ok, but it seems not correct for Catalyst 6506 ( show proc memory displayed the total memory is 512MB, but the WhatsUP displayed only 64MB only )
View 1 Replies View RelatedWe recently installed two 2960, both of them with this fw version:
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
The switches see very few traffic (under 40MB on all interfaces, summed, so far), however, I/O memory utilization is about 80% as can be seen from the show memory command:
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor 2B89A18 73969000 27198964 46770036 45060368 29367536
I/O 6200000 14680064 12185292 2494772 2323116 2380896
Driver te 1A00000 1048576 44 1048532 1048532 1048532
The memory allocated is almost all Packet Data, by init, "sho memory io dead" returns zero, the memory usage seems constant, there are no errors on the log, the switches operate correctly, no packet has ever been dropped, CPU usage is about 4%.
Here I showed info for one switch, the other is in the same situation. I just want to know if this behavior is expected, I don't want to find out problems when the switches will be in production whit real traffic.
I have the problem that our ciscoworks server gets out of memory after few days. The memory utilization is always getting higher an higher (above 95%). Sometimes it is only after 3 days and sometimes it is after 1 week. So it happens not regularly. I have made an screenshot from the services which use a lot of memory. And at this time the memory utilization is getting higher and higher again....I think there is a problem with tomcat or dbsrv10.exe, there are also a lot of cwjava.exe running.
View 8 Replies View RelatedWe recently added about 400 users to our network for a total of 1000. Looking at the ASDM we are holding very tight to 75% utilization and we have 256mbs. This is also running IOS 8.2(1). Our firewall recently crashed after a major download was forced through it. This was after only being booted up for about a week. We had reloaded it a week prior after having ran it for about a year without issue. We havent made any changes in the last month other than adding more users to our network.
View 3 Replies View RelatedI have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.
View 14 Replies View RelatedI've noticed that my 6509's running VSS seem to have high I/O memory utilization.
I/O memory: Sw/Mod Bytes: Total Used %Used
1/1 8126344 7886544 97%
1/2 11796240 11442472 97%
1/5 RP 12058384 10715832 89%
1/5 SP 8388608 8104304 97%
1/7 8126344 7886544 97%
[code]....
We terminated about 25 site-to-site VPN tunnels on the Cisco ASA 5540 (2 GB RAM). It appears that the memory utilization is getting higher when adding the tunnel. We are planing to remove those 25 VPN tunnels out 5540, and soon we will add additional 40 VPN tunnels on it. So it will be total around 65 tunnels, and maybe add couple tunnels per year for the future grow, but about 25 VPN tunnels are using at all the time, the others are just backup purpose, standby only. We are looking for the new network device (router or ASA) to accommodate the needs. Which network device is better to handle VPN tunnel for this infrastructure?
View 5 Replies View RelatedI noticed on the 2960 switches we have deployed that are running the latest IOS, 12.2(58)SE2, memory utilization is really high (almost 80 percent). I have not noticed any side effects but I wanted to verify this is acceptable. My question is does the high memory utilization matter? I see this may be related to bug CSCtw83946 but no resolution is mentioned.
I did some testing various IOS revisions and below is what I have found using a WS-C2960-48TC-L with default configuration and only my laptop connected to a switchport in vlan1. You will notice memory utilization will grows with each version but jumps drastically with 58. One difference with 58 I needed to use a different command to retrieve memory utilization. The output was gathered by pasting the output of the show command into the Cisco Output Interpreter on their website.
IOS
Show Command
Output
c2960-lanbasek9-mz.122-35.SE5.bin
show memory
[Code]....
I am facing high memory utilization in Cisco 2960 switch having IOS version 12.2(55)SE3.
The error we are getting is:
A "LiveHealthAlarm" event has occurred, from SwCiscoIOS device, named Switch2960. eHealth Alarm Start Time - Fri 09 Nov,2012 - 03:02:48 eHealth. Switch2960-RH-MemoryPool-Processor-Processor-1.Memory utilization high-Threshold set at 70%SPECTRUM ALARM ID|22233284 I have attached the logs also.
I have a new cisco 3750 stack comprised of 8 members (6 x 3750G-48PS and 2 x 3750V2-48PS) running 'c3750-ipservicesk9-mz.122-58.SE2.bin'. I am seeing high memory utilisation, it seems to sit fairly stable and I do not see an increase but this has only been running a few days. No errors or performance issues. Should this be a cause for concern?
View 3 Replies View RelatedWe had a stack of 4 qty 3750g running IP base on ver 12.2.32, then installed a 3750x to the stack and upgraded the whole stack to 15.0.2 SE3. In doing so, we noticed that the memory utilization jumped from 60-70% to 83-84%.
We had the same issue occur when upgrading to 15.0.2 SE3 on another stack that was 6 qty 3750g running ip-services, but this one jumped to 90%. On the 6 qty stack, we downgraded to 12.2.55 and the memory util went back down to 60-70%.
On the mixed stack, we replaced the 3750x with another 3750g and downgraded the whole stack to 12.2.55, however, the memory utilization did not drop down. As far as I can tell, no config changes have changed from the original IOS.
I upgraded the newest IOS 15.0(1)SE for our SW C2960-24-TT-L, the process was succeseful. However, we found SW memory utilization raised to 82% this morning in normal situation. (Momery: Total 21341260, Used17471692) Did you guys meet the same problem after upgrading to 15.0(1)SE? I also would like to know what the normal memory utilization is? and what is the impact of memory utilization highly?
View 8 Replies View RelatedI upgrade the IOS of my switch 3560 from C3560-IPBASE-M), Version 12.2(25)SEB4, To C3560-IPBASEK9-M), Version 12.2(55)SE5 after that the utilizatio of the memory increase to 80% I attached the output of show memory statistics history
View 5 Replies View RelatedIt's impossible to use acs 5.2 recovery DVD to cisco 1121 acs 5.1?
View 7 Replies View Relatedintegrated the Cisco ACS 1121 with 5.1 and AD and been able to use multiple policies to permit or deny access to different NDG? I am able to authenticate agains AD but I am having an issue with getting the policies to use the user memberOf attribute to set access levels.
View 1 Replies View RelatedIt has been more than a year since a customer bought a Cisco ACS 1121. It was unpacked then and the PAK is lost, no where to be found. Is there any way to retrive the lost PAK ?
View 19 Replies View Related