I have a problem upgrading an appliance CSACS 1121 from version 5.1 to 5.2 because restore DVD has image of 5.1 not 5.2 and in cisco.com appears only two files 5.2-0-26-1.tar.gpg and ACS_v5.2.0.26.iso, the first image is a patch and the second I'm not sure if is image for version 5.2, in case if appropriate which would be the correct commands to perform the upgrade using CLI.
View 4 RepliesIs it possible to have Dual NIC on ACS v5.2 such as teaming or any else??
I am thinking of connecting the two NIC on the CSACS-1121-K9 appliance to two switches on the same network, but wondering if it will be possible or not.
We upgraded a CSACS-1121 from ACS 5.2 to ACS 5.4 with CLI Application upgrade ACS_5.4.0.46.0a.tar.gz FTP After ACS reboot, services never start... After 15 hours, we always get same message:
ACS/admin# show application status acs
Application initializing...
Status is not yet available.
Please check again in a minute.
We installed patch 5-4-0-46-2.tar.gpg but we got same issue for 2 hours ...What could I do?
We have 2 CSACS 1121 with Cisco ACS 5.2.0.26.10 The primary server manages 20000+ authentications per day. Its memory utilization increases everyday. It is now at 83% , there a limit?,What will happen when memory utilization reach this limit?,What can we do to purge memory utilization? (reboot, service restart.
View 11 Replies View RelatedIs it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies View RelatedHow to know the Red Hat OS version in the ACS 1121 appliance?
View 1 Replies View RelatedWe are currently running a ACS 1113 with version 4.2 software. We are going to replace the 1113 ACS with two 1121 ACS.
View 1 Replies View RelatedFound the internet not working after upgrade of versions. Managed a work around by disabling KAS2013 Firewall settings and using MS Firewall. (desktop)
This is not the correct way of config and as my laptop works fine with KAS2013 firewall enabled.
I checked system IP ...ipconfig settings and wonder about matching up gateways??
I cannot import certificate from CA (Certificate Authority). When I attempt to install the certificate to CSACS SE 4.2, the following error occurs during installation: "Unsupported private key file format".
View 7 Replies View RelatedDoes the new UCS hardware change anything ?Can we bundle 2 NICs somehow to get interface redundancy ?If still not possible to configure that in ACS 5 itself:Can it enentually be done on the "hardware" level within the appliance firmware (UCS BIOS) ?(RHEL would provide NIC bonding,,, unfortunately its not accessable from ACS5 CLI)
View 6 Replies View RelatedI am scanning the documentation for CPI 1.2, trying to get it to use CSACS 5.3 for my authentication/Authorization. The docs say to create a TACACS Shell Profile, and add the TACACS A/V Pairs as needed... . nowhere could I find a listing of AV Pairs I can use to grant authorization. I did see that what ever pairs I did use, I must keep the menu chain in tact..
View 6 Replies View RelatedI have an ACS applicance that had a version 5.1 and i did an upgrade to 5.3 with latest patch.For some reason, the runtime process got stuck in (reinitializing and restarting) state.i did the recommended action to perform ACS stop and ACS start and even hard reset of the appliance, but it did not cut itThis process turned out to be a bug and it should have been fixed in version 5.3, but it has not i guess
i know that acs reset-config will solve the issue, but i have a problem here , the license file will be deleted as well with the config and i cannot find a way to export the license and then import it into the reseted config ACS hardware. Unfortunately, the license file is not saved anywhere in the company and i cannot affort to lose it.how to export the license from the applicance (CSACS-1120)?
Is it possible to deploy the CSS11501 in one arm design to loadbalance the authentication traffic Radius across CSACS servers which is on UDP 1645 or 1812 port, is it required to configure the NAT or not, if yes how can define the shared secret in the CSS. also tell me how to configure the keepalive for udp traffic in this scenario other then default icmp keep alive
View 2 Replies View RelatedI'm trying to join a band new CSACS-1120 to our active directory without success. The process in it self should be pretty straigh forward, but so far no luck.
I've configured the relevant info under "Users and Identity Stores > External Identity Stores > Active Directory.
Active Directory Domain Name: xxx.com
Username/Password : domain administrator account
When I test connection I get a info dialog "This machine is currently connected to domain xxx.com".After which I try to save changes which gives a reply ""This System Failure occurred: {0}. Your changes have not been saved. Click OK to return to the list page."
I've noticed that in the system log "show logging system tail" that I get a exception as soon as I enter the AD configuration page and subsequently every time I perform a action on that section.
Why the AD join keeps on failing and what the debug exception I'm getting means?
It's impossible to use acs 5.2 recovery DVD to cisco 1121 acs 5.1?
View 7 Replies View RelatedI wonder if you can migrate the cisco ap 1121 by WCS, could not find any specific documentation.
View 3 Replies View Relatedintegrated the Cisco ACS 1121 with 5.1 and AD and been able to use multiple policies to permit or deny access to different NDG? I am able to authenticate agains AD but I am having an issue with getting the policies to use the user memberOf attribute to set access levels.
View 1 Replies View RelatedIt has been more than a year since a customer bought a Cisco ACS 1121. It was unpacked then and the PAK is lost, no where to be found. Is there any way to retrive the lost PAK ?
View 19 Replies View RelatedI have a clarification related with ACS 1121. Client needs a solution for ACS feature, instead of investing on ISE Base, is there any model exists as ACS appliance only. I believe ACS 1121 is going to be EOS and it says SNS 3415 is the replacement model .
What I am confused is , It is an ISE as well as ACS and there is separate licensing for ISE (as base and advanced). What should i do , if i need to select SNS 3415 as ACS appliance ? is it built in or should i need to add anything extra ?
Newly shipped cisco ACS appliance 1121 has been shipped with ACS version 5.0 , I need to downgrade to ACS version 4.2,0 , I could not see recovery CD or DVD for acs 4.2 along with shipment , Is ACS 1121 appliance is comptaible to acs 4.2.0 version ? .
My ACS BOM details
CSACS-1121-K9
ACS 1121 Appliance With 5.1 SW And Base license
[code]....
how to configure LAN teaming in Cisco ACS 1121. My requirement is to have virtual IP in the server with two physical IPs in the available 2 interface in the server.
View 1 Replies View RelatedI am trying to add ACS 1121 (ver 5.3) to monitoring and seems that MIB are missing. Need MIB for this device which I can use in monitoring tool.
View 1 Replies View RelatedI have 5 installations of ACS appliances (ACS 1121 running ACS 5.3). Is there a way to monitor them via SNMP? The AD client keeps dying on one of them, and even with the newest patch it's not up. Also, i want to monitor them up/down, CPU, memory... basic network monitoring to make sure my devices are healthy.
Any one know if that can be configured? I figured i'd ask here before opening a TAC.
The user "shreedhar" is getting authenticated locally and not through TACACS+ (Cisco ACS 1121 appliance running ACS 5.1).
In the switch, after entering credentials, the switch says, "Authentication failed - login using local mode". (Not the exact message but close enough!).
In ACS 5.1 -> Monitoring and Reports->Dashboard->My Favorite Reports->Authentications-TACACS+, I am getting the following error, "13011 Invalid TACACS+ request packet - possibly mismatched Shared Secrets".
Configuration in switch is as follows:
feature tacacs+
username admin password 5 $1$joEvYokP$5wZ1mtpBlxuoKMEWbFzRY1 role network-adminusername shreedhar password 5 $1$x8u5N4IR$NbVcY1u6CuoXYkMgXs60l/ role network-admin
tacacs-server key 7 "Ti!23456"ip tacacs source-interface loopback0acacs-server test username demo password demo123 idle-time 3 tacacs-server timeout 10tacacs-server deadtime 5tacacs-server host 192.168.31.11 key 7
[code]....
Is #the encrypted TACACS+ shared secret key from switch not being decrypted by ACS 5.1 as it requires a clear-text password? Could it be the reason for the above error?
I have an issue with applying a patch to an ACS 1121 appliance running version 5.2.0.26. I have 5 units that needed updating and the first one is the unit with the problem. The subsequent ones updated with no issues.
When I do a show version the 5.2.0.26.10 does not show. When I try to do a reinstall I get back patch all ready exists. When I try to do an uninstall I get back patch does not exist.
Is there a command can wipe out patch 10, so I can start over? The CLI factory-reset only wipes the web configuration not the running-config or IOS.
My customer has an ACS 1121 version 5.4. Now we want to install a secondary ACS 1121.
View 2 Replies View RelatedWe have a WLC 4404 with about 85 1121 and 1241 APs. - I just added 6 new 3501E with Antennas, and configured the a new SSID, but non of my clients can connect to any of the 3501s. One solution from a tech was to update the NIC drivers. I verified that all test clients are 802.11N and sometimes they find the 3501 but often they switch to another of the older and weaker 1121 or 1241s. On one test I had a 3501 just outside his room and his client nic was picking up a weak signal 2 floors up, then it would go to one 1 floor down. eventually we could get it to feed of the nearest 3501 but it would go back to another 1121 or 1241 soon thereafter,.
View 5 Replies View RelatedIm installing & configuring a new ACS 1121. Ive updated to version 5.3 with patch:This temporarily solves my Active Directory problem but i still would like to have the NTP server pointing to the same reference as the Active Directory.
View 1 Replies View RelatedIam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.
I have a 1121 autonomous AP which I switched to the lightweight mode by copying the LWAPP ios to its flash and issuing the command boot system flash IOS_file_Name. After that I was unable to associate the AP to my wireless controller because it was continiously rebooting. Unfortunately this AP does not have a console port so I can access the debug and see what is happening. And I was not able to switch it back to the autonmous mode becaus the AP won't accept the Autonomous mode IOS anymore.
View 2 Replies View RelatedI have to migrate two appliances ACS SE 1112 under 4.0.1 to new two appliances ACS SE 1121 under 5.2 version.I would like to clarify the procedure to do it by minimizing down time impact.I saw there are Migration Utility and Import Tool but do I need an Intermediate Windows Server to do this migration ?
View 1 Replies View RelatedI have an ACS Server 5.1 which is used to authenticate my cisco and non-cisco devices. however when I take report on my authentications, the time shown in the report is wrong. However, when I take my mouse pointer to the report , the correct time is highlighted.
View 4 Replies View RelatedIs it possible to edit the hosts file on an ACS 1121 server running ACS 5.2? Our problem is we have a single domain with multiple domain controllers at different sites. So when the ACS server tries connecting to the domain it randomly picks a domain controller which it can't connect to thus causing it to fail.
View 5 Replies View Related