Cisco :: 3501E Not Integrating In WLC4404 With 1121 And 1241 APs
Nov 11, 2012
We have a WLC 4404 with about 85 1121 and 1241 APs. - I just added 6 new 3501E with Antennas, and configured the a new SSID, but non of my clients can connect to any of the 3501s. One solution from a tech was to update the NIC drivers. I verified that all test clients are 802.11N and sometimes they find the 3501 but often they switch to another of the older and weaker 1121 or 1241s. On one test I had a 3501 just outside his room and his client nic was picking up a weak signal 2 floors up, then it would go to one 1 floor down. eventually we could get it to feed of the nearest 3501 but it would go back to another 1121 or 1241 soon thereafter,.
View 5 Replies
ADVERTISEMENT
Jan 7, 2013
how to migrate from WLC4404 to WLC5508. I want to know your propositions.
I could replicate the configuration manually but there is a lot of confirugation menus and all. If both could be online and migrate the AP to the new one until there is none on the old one, it would be great.
View 5 Replies
View Related
Oct 3, 2012
We have two Cisco Wireless Controller 4404 with the IOS Version 7.0.220.0 and a lot of access points (ca. 170). Now i wan't to reboot a group of Access points where i found over a filter..Or how can i reboot all the Access Points at the same time over the Controller Interface? Is it possible? I only found the option in the WebGui where i can reboot 1 Access Point at the same time with "hardware reset".
View 5 Replies
View Related
Jan 9, 2012
i have 2x WLC4404 they are in the same mobilitygroup and worked since a long time. Three days ago, ill upgraded one of them from 6.0.199.4 to 6.0.202.0. I have nearly 90 APs (1231,1242, different models)
The upgrade was successfull and i moved the APs from WLCA (6.0.199.4) to WLCB (6.0.202.0) almost all APs worked fine without 6 of them. This 6 APs cannot ping the AP-Manager-Interface from WLCB. But they can Ping the Router in this vlan, WLCA-AP-Manager and all APs in this subnet. They only cant get to the AP-Manager-interface from WLCB. Ping to Managementinterface of WLCB is also ok. Management and AP Manager are in different subnets. All APs and the AP-Manager-Interfaces from WLCA+WLCB are in the same subnet.
Switchportconfig and routing are ok. ive resetet the APs to default, checked switchport config, resetet switchport, power down ap for a while. ive tried many things, but nothing worked.I ever only can ping AP-Manager from WLCA, but not WLCB (again same subnet, and about 80 other APs work fine)
If i install a new AP on the same switchport, it works fine, without any issues. when i than unplug the "newAP" from this switchport and again connect the "oldAP" it can ping WLCA+WLCB and anything is fine.
Now i have the next and bigger problem nearly 15 of the APs that worked fine after upgrading, for now 3days+. Now they cannot ping the WLCB-AP-Manager-int too. And they dont failover to the WLCA with (6.0.199.4), i can reboot but they ever try to connect to WLCB. But they know both controllers.I only can get them to WLCA via ssh: capwap ap primary-base WLCAsname WLCAsmanagementIP..why the APs dont fail over if they dont reach WLCBsAP-Managerinterface?why i cannot ping WLCBs AP-Mana-Int from some APs.
View 7 Replies
View Related
Jan 6, 2011
Trying the config as depicted in the WCS 7 config guide? I have tried today to integrate WCS 7 with ACS 5.1 and got a partial success. I have created a unique Shell Profile that invokes for the WCS only which contains 1 role (role0=Root) and 73 task entries (as copied from the WCS group pages) and I can log in to WCS with the new account, but some things I dont appear to have priviledges for, such as Reports. Is there any way to debug which task WCS thinks I dont have to do this?
View 8 Replies
View Related
Aug 15, 2012
how to set up support 802.11n on WLC4404 or WLC5508 in the 2.4Ghz? WLC4404 supports 802.11n? or support this protocol only in the brochures? I spent a few days, but did not get the result. I'm connected at speeds 65/130Mbit, but the real speed tests never exceeded 45Mbit. The AP from the test laptop is 7-10 meters.I tested the laptops with a Linksys AP E1200-EE ( 40Mhz, FastEthernet uplink port...)and received nearly 100Mbit!
At WLC5508 able to connect at speeds 150/300Mbit/c but only in the 5GHz band, but real speed tests never exceeded 70Mbit.In 2.4Ghz range I connected at speeds of 130/144Mbit/c, but actual measurements showed no more than the 45Mbit.
All tested with iperf and with site speedtest.net.
iperf -w64K -s
iperf -w64K -i 2 -t 300 -c x.x.x.x
Laptops: Asus (Atheros AR9002WB-1NG) and Sony (Advanced-N 6230).
My tests AP: 3501I-E and 1252AG-A
SW on WLC5508 7.2.110.0
AP tested in different variants - open system and WPA2+AES.
[code]....
View 5 Replies
View Related
Oct 15, 2012
We currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
View 4 Replies
View Related
Mar 11, 2012
I am using Cisco LMS 3.2.1 with ACS 5.1, actually, i want to integrate my Cisco Work with ACS 5.1 in AAA mode i already setting up the AAA mode to Cisco ACS, when i apply the configuration, i got failed as image attached.
What should i do to resolve the problem ? i have configure the ACS in Network Devices and AAA Client, i have added the Cisco Work Address to ACS, but i got the same error.
Besides, would you like to give me some explanation about the function of AAA mode Setup on Cisco Work,
is it used for User Authentication to logging in to Cisco LMS, or is it used for discovery process (Credential Information) when we want to add some devices into Cisco LMS ?
View 3 Replies
View Related
Jan 4, 2012
I am trying to populate the LMS 4.1 components to ACS.
View 2 Replies
View Related
Mar 20, 2013
How to disable dhcp proxy on controller and what is the impact of doing it in the middle? We tried once by giving 'config dhcp proxy disable' command but seeing virtual ip again.(likely it gets back to proxy mode). We also have ip helper address on the L3 interface. We have only external dhcp servers configured..
View 5 Replies
View Related
Jan 10, 2012
I have 2 controllers as below one with 6.0 version and other with 5.2 version AIR-WLC4404-100-K9 6.0.202.0 AIR-WLC4402-12-K9 5.2.178.0 GUEST..Control path between controller flaps.All mobility anchors on wlan index 7 are down.All mobility anchors on wlan index 3 are down.Control path to mobility member x.x.x.x is down.No problem observed when i have software 5.2.178.0 on both the controller.
View 35 Replies
View Related
Oct 1, 2012
Continuous dropping out some of them Access Points registered on the Primary Controller . What is the reason for this. We have a problem the last 2 weeks. What are the causes of falling out controler Access Points. The problem does not appear from logs. 70 LWAPs registered over Primary Controller. All AP mode is Local.
Primary controller model: WLC4404 SW:7.0.116.0
Secondary Controller: WS-SVC-WISM-1-K9 SW:7.0.116.0
Tertiary Controller: WS-SVC-WISM-1-K9 SW:7.0.116.0
AP models: LWAP-1131 LWAP-1142 LWAP-1242 SW: 12.4(18a)JA3
View 2 Replies
View Related
Aug 13, 2012
I need to integrate a 2504 WLC with a windows 2003 LDAP server for extented authentication, is there any guides available for this ?
View 1 Replies
View Related
Mar 10, 2012
I am using ACE30 having s/w version: 4.2. I am using ACS 5.2
I have used the below commands to add ACE with ACS for AAA.
tacacs-server key 7 "nacs0wvd!q"
tacacs-server host 96.86.76.66 key 7 "nacs0wvd!q"
tacacs-server host 96.86.76.67 key 7 "nacs0wvd!q"
[Code].....
I am getting authenticated by ACS, but the problem is authorization is not happening. In ACS, i have just added the device IP using TACACS+.
View 0 Replies
View Related
Jan 2, 2013
I have 3 Cisco AP 1140 at my customer (Service Industry) place, so they requenst us to provide Hotspot solution to them for managing the Internet connection for limiting to their Customers over the account system. Let me know how i can integrate hotspot BOX with Cisco AP.
View 3 Replies
View Related
Feb 2, 2012
I know nothing about Tablets (iPad or Android) or their operating system. My wife is interested in getting a iPad 2 or Android tablet.
I have a home WiFi network based on two laptops and a desktop. They are all running Windows OS. I also have 3 external drives and two printers USB wired into the main desktop.
I have two questions:
1) Will I be able to integrate an iPad/Android tablet into the Windows home network so as to be able to access the .jpg photographs on the desktop drives?
2) Will the tablet be able to output work to the printer attached to the Windows Desktop?
View 3 Replies
View Related
Nov 20, 2011
I have a single production 5510 with 2 contexts. Now I want to integrate the secondary failover unit. My question is: How much configuration needs to be done on the secondary firewall? How much of the configuration will be sync'd from the primary to the secondary when the secondary is connected?
For example, do I need to add the following on the secondary or will it be sync'd from the primary?
admin-context NAME
context NAME
allocate-interface Ethernet0/0.14
[Code].....
View 3 Replies
View Related
Dec 17, 2012
We have an existing network with a Catalyst 4510 core switch and departmental 3560 switches connected via fiber. Due to company restructure we can no longer afford to buy new 3560's when anything goes wrong so this week I purchased an SG200-26 which I'm trying to get onto the network.
This is a legacy network which I didn't setup so my Cisco skills are somewhat limited (another reason for the SG200's hopefully), anyway have been looking at the configs on the existing switches and trying to match settings in the SG200 setup however not getting anywhere! I have the config from the dead switch so I can show what needs to be achieved, any experience in downgrading environment in a similar way?
View 7 Replies
View Related
Mar 7, 2012
I've just started a new job after a couple of years not touching cisco gear and been pitched in... My new employer has a network that's Juniper based. We've inherited a load of Cisco switches as part of the deal for hosting matches during the Rugby world cup (plus a load of Aruba wireless gear that promises to be my very own special millstone, but that's bye the bye.)
My task is to hang these catalyst 2960's onto our existing infrastructure via fibre connections.
On the Juniper switch, there are four vlans being pushed to the port the cisco's hooked into: Code...
View 7 Replies
View Related
May 31, 2013
It's impossible to use acs 5.2 recovery DVD to cisco 1121 acs 5.1?
View 7 Replies
View Related
May 1, 2012
I wonder if you can migrate the cisco ap 1121 by WCS, could not find any specific documentation.
View 3 Replies
View Related
May 15, 2011
integrated the Cisco ACS 1121 with 5.1 and AD and been able to use multiple policies to permit or deny access to different NDG? I am able to authenticate agains AD but I am having an issue with getting the policies to use the user memberOf attribute to set access levels.
View 1 Replies
View Related
Jul 1, 2012
How to know the Red Hat OS version in the ACS 1121 appliance?
View 1 Replies
View Related
Jan 6, 2012
It has been more than a year since a customer bought a Cisco ACS 1121. It was unpacked then and the PAK is lost, no where to be found. Is there any way to retrive the lost PAK ?
View 19 Replies
View Related
Jun 7, 2013
I have a clarification related with ACS 1121. Client needs a solution for ACS feature, instead of investing on ISE Base, is there any model exists as ACS appliance only. I believe ACS 1121 is going to be EOS and it says SNS 3415 is the replacement model .
What I am confused is , It is an ISE as well as ACS and there is separate licensing for ISE (as base and advanced). What should i do , if i need to select SNS 3415 as ACS appliance ? is it built in or should i need to add anything extra ?
View 3 Replies
View Related
May 2, 2011
Newly shipped cisco ACS appliance 1121 has been shipped with ACS version 5.0 , I need to downgrade to ACS version 4.2,0 , I could not see recovery CD or DVD for acs 4.2 along with shipment , Is ACS 1121 appliance is comptaible to acs 4.2.0 version ? .
My ACS BOM details
CSACS-1121-K9
ACS 1121 Appliance With 5.1 SW And Base license
[code]....
View 2 Replies
View Related
Mar 27, 2011
how to configure LAN teaming in Cisco ACS 1121. My requirement is to have virtual IP in the server with two physical IPs in the available 2 interface in the server.
View 1 Replies
View Related
Mar 26, 2012
I am trying to add ACS 1121 (ver 5.3) to monitoring and seems that MIB are missing. Need MIB for this device which I can use in monitoring tool.
View 1 Replies
View Related
Nov 28, 2010
I have a problem upgrading an appliance CSACS 1121 from version 5.1 to 5.2 because restore DVD has image of 5.1 not 5.2 and in cisco.com appears only two files 5.2-0-26-1.tar.gpg and ACS_v5.2.0.26.iso, the first image is a patch and the second I'm not sure if is image for version 5.2, in case if appropriate which would be the correct commands to perform the upgrade using CLI.
View 4 Replies
View Related
Aug 13, 2012
I have 5 installations of ACS appliances (ACS 1121 running ACS 5.3). Is there a way to monitor them via SNMP? The AD client keeps dying on one of them, and even with the newest patch it's not up. Also, i want to monitor them up/down, CPU, memory... basic network monitoring to make sure my devices are healthy.
Any one know if that can be configured? I figured i'd ask here before opening a TAC.
View 2 Replies
View Related
Jul 30, 2011
The user "shreedhar" is getting authenticated locally and not through TACACS+ (Cisco ACS 1121 appliance running ACS 5.1).
In the switch, after entering credentials, the switch says, "Authentication failed - login using local mode". (Not the exact message but close enough!).
In ACS 5.1 -> Monitoring and Reports->Dashboard->My Favorite Reports->Authentications-TACACS+, I am getting the following error, "13011 Invalid TACACS+ request packet - possibly mismatched Shared Secrets".
Configuration in switch is as follows:
feature tacacs+
username admin password 5 $1$joEvYokP$5wZ1mtpBlxuoKMEWbFzRY1 role network-adminusername shreedhar password 5 $1$x8u5N4IR$NbVcY1u6CuoXYkMgXs60l/ role network-admin
tacacs-server key 7 "Ti!23456"ip tacacs source-interface loopback0acacs-server test username demo password demo123 idle-time 3 tacacs-server timeout 10tacacs-server deadtime 5tacacs-server host 192.168.31.11 key 7
[code]....
Is #the encrypted TACACS+ shared secret key from switch not being decrypted by ACS 5.1 as it requires a clear-text password? Could it be the reason for the above error?
View 1 Replies
View Related
Aug 11, 2011
Is it possible to have Dual NIC on ACS v5.2 such as teaming or any else??
I am thinking of connecting the two NIC on the CSACS-1121-K9 appliance to two switches on the same network, but wondering if it will be possible or not.
View 1 Replies
View Related
Jun 3, 2012
I have an issue with applying a patch to an ACS 1121 appliance running version 5.2.0.26. I have 5 units that needed updating and the first one is the unit with the problem. The subsequent ones updated with no issues.
When I do a show version the 5.2.0.26.10 does not show. When I try to do a reinstall I get back patch all ready exists. When I try to do an uninstall I get back patch does not exist.
Is there a command can wipe out patch 10, so I can start over? The CLI factory-reset only wipes the web configuration not the running-config or IOS.
View 7 Replies
View Related
