I have 5 installations of ACS appliances (ACS 1121 running ACS 5.3). Is there a way to monitor them via SNMP? The AD client keeps dying on one of them, and even with the newest patch it's not up. Also, i want to monitor them up/down, CPU, memory... basic network monitoring to make sure my devices are healthy.
Any one know if that can be configured? I figured i'd ask here before opening a TAC.
I am trying to add ACS 1121 (ver 5.3) to monitoring and seems that MIB are missing. Need MIB for this device which I can use in monitoring tool.
View 1 Replies View RelatedI am configuring new ACS 1121 appliance with version 5.3 and wanted to know how to configure Remote Database settings in ACS5.3 Is that necessary to configure that option ?
Also one more thing I can see that ACS 5.3 generates lots of logs is there any solution to reduce such logs. It seems many unuseful logs which are system related are getting logged into device which might no be good for memory requirements of device.
We currently have a few 5505s installed at client sites which are connected via s2s ipsec VPN to our datacenter's 5510. We are using Nagios to monitor the local data center and remote client infrastructure (over the VPNs) which has been working well.
We would like to also monitor the remote 5505s using SNMP over the s2s tunnels but it doesn't seem to be working, the connection is timing out. We've configured the remote 5505s with the same snmp statement we used on the 5510 (snmp-server host inside <remote datacenter IP> poll community ***** version 2c) yet the Nagios SNMP check cannot connect to the remote 5505s. We've also tried the command using 'outside' without any luck, not sure how to get SNMP to route over the VPN.
I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies View Related how snmp monitoring works when we have WLC in the networking.Before the WLC 5508 instalation, we had the Nagios monitoring each Access Point in the networking. Today, the Nagios still monitoring the networking, but the Nagios cannot get the same information of the APs (CPU, status interface, memory, etc).Now, the WLC controls each AP, the IP address, netmask, community (of all AP) are the same before the WLC instalation. I have tried to configure the SNMP information in Management>>SNMP>>Communities, but these configuration are from WLC and not from each AP.
How can I configure the SNMP setting in my AP to still use the Nagios to monitoring the networking?
I am building a few 3750 stacks, I want to be able to poll/monitor each individual switch in the stack but as it only has 1 ip associated with the stack how can I do this. I am polling the uplink interfaces but as I only have uplinks on the top and bottom switch I am blind to a switch going down in the middle of the stack.
View 4 Replies View RelatedI'm a C# programmer and as part of my software I need to monitor some Cisco Catalyst 3560V2 24 switches using SNMP (By reading MIB/S data).Apparently this switch supports more than 50 different MIBs.My question is which MIB/MIBS contains general health data (parameters) that may determine if the switch is OK, Degraded or Malfunctioned.
View 0 Replies View RelatedI am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
View 2 Replies View RelatedI was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
I have two 6509E's configured with VSS. In this configuration, is it possible to monitor the CPU and memory of each switch independently using SNMP?
View 1 Replies View RelatedI'm running 12.2(33)SXJ1 on a 6500 with several IPv6 BGP peers. Is there any way to monitor the BGP status of IPv6 peers? I've been through the BGP4 mib and cant seem find a way to check the status of IPv6 peers.
View 4 Replies View RelatedWe have C7206VXR NPE-G2 platform with transceiver which support DOM.Could we monitor DOM tx/rx level statistic through snmp for 7206 platform?In CLI result of command "sh interf GigabitEthernet0/1 transceiver" give some information.We tried search for some MIB In "MIB locator" on cisco.com.
View 2 Replies View RelatedIs temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies View RelatedIt's impossible to use acs 5.2 recovery DVD to cisco 1121 acs 5.1?
View 7 Replies View Relatedintegrated the Cisco ACS 1121 with 5.1 and AD and been able to use multiple policies to permit or deny access to different NDG? I am able to authenticate agains AD but I am having an issue with getting the policies to use the user memberOf attribute to set access levels.
View 1 Replies View RelatedIt has been more than a year since a customer bought a Cisco ACS 1121. It was unpacked then and the PAK is lost, no where to be found. Is there any way to retrive the lost PAK ?
View 19 Replies View RelatedI have a clarification related with ACS 1121. Client needs a solution for ACS feature, instead of investing on ISE Base, is there any model exists as ACS appliance only. I believe ACS 1121 is going to be EOS and it says SNS 3415 is the replacement model .
What I am confused is , It is an ISE as well as ACS and there is separate licensing for ISE (as base and advanced). What should i do , if i need to select SNS 3415 as ACS appliance ? is it built in or should i need to add anything extra ?
I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies View Related Newly shipped cisco ACS appliance 1121 has been shipped with ACS version 5.0 , I need to downgrade to ACS version 4.2,0 , I could not see recovery CD or DVD for acs 4.2 along with shipment , Is ACS 1121 appliance is comptaible to acs 4.2.0 version ? .
My ACS BOM details
CSACS-1121-K9
ACS 1121 Appliance With 5.1 SW And Base license
[code]....
how to configure LAN teaming in Cisco ACS 1121. My requirement is to have virtual IP in the server with two physical IPs in the available 2 interface in the server.
View 1 Replies View RelatedIs it possible to have Dual NIC on ACS v5.2 such as teaming or any else??
I am thinking of connecting the two NIC on the CSACS-1121-K9 appliance to two switches on the same network, but wondering if it will be possible or not.
I have an issue with applying a patch to an ACS 1121 appliance running version 5.2.0.26. I have 5 units that needed updating and the first one is the unit with the problem. The subsequent ones updated with no issues.
When I do a show version the 5.2.0.26.10 does not show. When I try to do a reinstall I get back patch all ready exists. When I try to do an uninstall I get back patch does not exist.
Is there a command can wipe out patch 10, so I can start over? The CLI factory-reset only wipes the web configuration not the running-config or IOS.
My customer has an ACS 1121 version 5.4. Now we want to install a secondary ACS 1121.
View 2 Replies View RelatedI'm currently implementing Microsoft System Center 2012 Operations Manager, the curent stage of the project is to add the network devices to SCOM via SNMP in order to monitor them, I am able to add them all and monitor; however, my ASA 5510, although SCOM discovers the ASA via SNMP and adds it to the network monitoring list, it loses SNMP connectivy every 30 minutes, and 15 later it reconnect with SCOM, then after another 15 minutes it loses the connection again, and so on and so for.
View 1 Replies View RelatedIm installing & configuring a new ACS 1121. Ive updated to version 5.3 with patch:This temporarily solves my Active Directory problem but i still would like to have the NTP server pointing to the same reference as the Active Directory.
View 1 Replies View RelatedI have to migrate two appliances ACS SE 1112 under 4.0.1 to new two appliances ACS SE 1121 under 5.2 version.I would like to clarify the procedure to do it by minimizing down time impact.I saw there are Migration Utility and Import Tool but do I need an Intermediate Windows Server to do this migration ?
View 1 Replies View RelatedI have an ACS Server 5.1 which is used to authenticate my cisco and non-cisco devices. however when I take report on my authentications, the time shown in the report is wrong. However, when I take my mouse pointer to the report , the correct time is highlighted.
View 4 Replies View RelatedWe upgraded a CSACS-1121 from ACS 5.2 to ACS 5.4 with CLI Application upgrade ACS_5.4.0.46.0a.tar.gz FTP After ACS reboot, services never start... After 15 hours, we always get same message:
ACS/admin# show application status acs
Application initializing...
Status is not yet available.
Please check again in a minute.
We installed patch 5-4-0-46-2.tar.gpg but we got same issue for 2 hours ...What could I do?
We have 2 CSACS 1121 with Cisco ACS 5.2.0.26.10 The primary server manages 20000+ authentications per day. Its memory utilization increases everyday. It is now at 83% , there a limit?,What will happen when memory utilization reach this limit?,What can we do to purge memory utilization? (reboot, service restart.
View 11 Replies View RelatedIs it possible to edit the hosts file on an ACS 1121 server running ACS 5.2? Our problem is we have a single domain with multiple domain controllers at different sites. So when the ACS server tries connecting to the domain it randomly picks a domain controller which it can't connect to thus causing it to fail.
View 5 Replies View RelatedI have ACS1121 running version 5.1.0.44.6 on my network environement , I need to enable account lock-out for internal user during failed attempt for more than 8 times , How to achieve this . I could see account lock-out for administrator user account , not for internal user .
View 2 Replies View RelatedWe are currently evaluating a ACS 1121 running 5.2, we are trying to configure this to Authenticate eap-peap requests.
Our users will be using credentials in a username@example.com format, if the server sees a request using username@anotherrealm.com then it would forward the request to a external proxy radius server, if the server saw a request for our domain it would strip off the @example.com part and authenticate against AD.
Im finding it hard locating documentation to tell the server if a request comes from a NAS using username@example.com then strip @example.com and authenticate username against AD.
