Cisco :: WLC 5508 / Individual AP SNMP Monitoring?
Jun 15, 2011
how snmp monitoring works when we have WLC in the networking.Before the WLC 5508 instalation, we had the Nagios monitoring each Access Point in the networking. Today, the Nagios still monitoring the networking, but the Nagios cannot get the same information of the APs (CPU, status interface, memory, etc).Now, the WLC controls each AP, the IP address, netmask, community (of all AP) are the same before the WLC instalation. I have tried to configure the SNMP information in Management>>SNMP>>Communities, but these configuration are from WLC and not from each AP.
How can I configure the SNMP setting in my AP to still use the Nagios to monitoring the networking?
View 1 Replies
ADVERTISEMENT
Aug 26, 2012
Is there a way to ask the above switch how much power it's supplying to various ports?I've found some stuff in POWER-ETHERNET-MIB, but it's only the main power supply and the up/down status of the various ports.
It looks like what I want is
[URL]
but my SG500 tells me:
snmpwalk -v2c -cpublic serverswitch 1.3.6.1.4.1.9.9.402
CISCO-SMI::ciscoMgmt.402 = No Such Object available on this agent at this OID
View 6 Replies
View Related
Aug 30, 2012
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
View 17 Replies
View Related
Apr 3, 2012
We currently have a few 5505s installed at client sites which are connected via s2s ipsec VPN to our datacenter's 5510. We are using Nagios to monitor the local data center and remote client infrastructure (over the VPNs) which has been working well.
We would like to also monitor the remote 5505s using SNMP over the s2s tunnels but it doesn't seem to be working, the connection is timing out. We've configured the remote 5505s with the same snmp statement we used on the 5510 (snmp-server host inside <remote datacenter IP> poll community ***** version 2c) yet the Nagios SNMP check cannot connect to the remote 5505s. We've also tried the command using 'outside' without any luck, not sure how to get SNMP to route over the VPN.
View 15 Replies
View Related
Jan 27, 2013
I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies
View Related
Mar 26, 2012
I am trying to add ACS 1121 (ver 5.3) to monitoring and seems that MIB are missing. Need MIB for this device which I can use in monitoring tool.
View 1 Replies
View Related
Aug 13, 2012
I have 5 installations of ACS appliances (ACS 1121 running ACS 5.3). Is there a way to monitor them via SNMP? The AD client keeps dying on one of them, and even with the newest patch it's not up. Also, i want to monitor them up/down, CPU, memory... basic network monitoring to make sure my devices are healthy.
Any one know if that can be configured? I figured i'd ask here before opening a TAC.
View 2 Replies
View Related
Oct 3, 2006
I am building a few 3750 stacks, I want to be able to poll/monitor each individual switch in the stack but as it only has 1 ip associated with the stack how can I do this. I am polling the uplink interfaces but as I only have uplinks on the top and bottom switch I am blind to a switch going down in the middle of the stack.
View 4 Replies
View Related
May 23, 2011
I'm a C# programmer and as part of my software I need to monitor some Cisco Catalyst 3560V2 24 switches using SNMP (By reading MIB/S data).Apparently this switch supports more than 50 different MIBs.My question is which MIB/MIBS contains general health data (parameters) that may determine if the switch is OK, Degraded or Malfunctioned.
View 0 Replies
View Related
Mar 27, 2008
I am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
View 2 Replies
View Related
Apr 10, 2012
I was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
View 3 Replies
View Related
Oct 21, 2012
I have two 6509E's configured with VSS. In this configuration, is it possible to monitor the CPU and memory of each switch independently using SNMP?
View 1 Replies
View Related
Nov 5, 2011
I'm running 12.2(33)SXJ1 on a 6500 with several IPv6 BGP peers. Is there any way to monitor the BGP status of IPv6 peers? I've been through the BGP4 mib and cant seem find a way to check the status of IPv6 peers.
View 4 Replies
View Related
Feb 5, 2012
We have C7206VXR NPE-G2 platform with transceiver which support DOM.Could we monitor DOM tx/rx level statistic through snmp for 7206 platform?In CLI result of command "sh interf GigabitEthernet0/1 transceiver" give some information.We tried search for some MIB In "MIB locator" on cisco.com.
View 2 Replies
View Related
Jun 19, 2012
Is temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies
View Related
May 1, 2012
I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies
View Related
Apr 4, 2013
I'm currently implementing Microsoft System Center 2012 Operations Manager, the curent stage of the project is to add the network devices to SCOM via SNMP in order to monitor them, I am able to add them all and monitor; however, my ASA 5510, although SCOM discovers the ASA via SNMP and adds it to the network monitoring list, it loses SNMP connectivy every 30 minutes, and 15 later it reconnect with SCOM, then after another 15 minutes it loses the connection again, and so on and so for.
View 1 Replies
View Related
Sep 7, 2011
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
View 1 Replies
View Related
Jun 2, 2013
, I have a requirement by a customer that they will want to monitor the guest wireless access. Currently, we are proposing a Cisco Wireless Controller 5508 together with APs and the setup would be a dedicated VLAN for guest. I am wondering if Cisco ISE together with Cisco MSE would be sufficient?
Stuff to monitor and log are:
1. Guest username (I guess this would be self sponsored)
2. Company name
3. Websites accessed
4. Time, date and duration.
5. Logs are to be kept for 3 months at least.
View 3 Replies
View Related
Apr 4, 2013
I am using web authentication with my Wlc 5508 and I would like to check all users currently connected (ip, login used, MAC address, ...) with SNMP.
I am using an external web server and my client are authenticated with ldap.
I know I can receive these information with traps, but I would like to create a short program which will check all users when I click on a button.
View 2 Replies
View Related
Jun 11, 2013
How are certain settings/config transfered across to the AP's from the WLC, e.g. username and passwords, snmp strings etc.... I assume this is when the AP joins the WLC.More to the topic of the original question I had in mind, is it possible and if so, how? - to configure snmp read and write string from the WLC and push this config out to AP's. I can't believe someone will have to sit down (me) and SSH to 150+ AP's per WLC to configure SNMP.
One of the buildings lost connectivity to the WLC's breifly a couple of days ago and all seemed to have lost their SNMP settings. Connectivity was restored, but couldnt poll the APs. When I SSH'd on to a couple of AP's, and manually configured the snmp-server community xxxx ro - SNMP started working again. Since there are many, there must be an easier way of doing it.I've tried resetting the AP from the WLC and also powering down AP's and bringing them back up.
Using WLC 5508 on 7.4.100
Using AP's 2602 on IOS 15.2(2)JB$
View 1 Replies
View Related
May 16, 2013
We had a system outage due to power problems a few days ago, and now our WLC is showing short term packet loss when monitoring it using SNMP. We also monitor it using ICMP, but that shows no packet loss. I looked at the interface statistics on the WLC and all of the switches in between and there are no errors to be seen. is there any way to troubleshoot this problem on the WLC? I am more familiar with IOS than the WLC CLI.
View 10 Replies
View Related
Jun 10, 2013
We faced one recent issue with WLC configuration behavior and explaining our observation and workaround we did.Requirement is to manage the WLC (5508 with 7.4 code) using two SNMP managers in different locations. Also these two Servers should use the same community string to manage WLC.
We were able to configure the SNMP community string for one server IP (to allow access) through GUIWhile trying to add another Server – IP with same community string – it didn’t allow As per the configuration guide, Controller can use only one IP address range to manage SNMP community. So we cannot configure the same community string to allow only two different server IP addresses [code] We currently configured the major subnet ( 10.x / 8 - two match both server addresses) and it works fineAlso when we tried 0.0.0.0 / 0.0.0.0 , it didn’t work (SNMP was failing)But this creates a security issue wherein anybody can poll the WLC.
View 1 Replies
View Related
May 20, 2013
I am working on a wlc 5508 in a lab environment doing snmp reporting & i was wondering if there is anyway to after the timing on how quick the snmp traps appear on the trap log page? I have looked through the gui but cant seem to find anything, so not too sure if there is a cli command, the traps come in very quickly on the nms way before they appear on the trap log page.
View 1 Replies
View Related
Jul 3, 2011
I'm using 50MB/s hub provided by virgin media. The thing is everything works perfectly fine except the download speed on my personal unit worries me a bit. As I perform download speed test online, at my unit, I usually get the speed of 40 up to 49.7 MB/s, upload 0.7 - 1.5MB/s. However in case of downloading the same file from the same source other pc at our home network usually download it at twice or trice the speed my unit does. I'm positive that my card is capable of speeds up to 100MB/s.
View 3 Replies
View Related
Jan 13, 2011
I'm using Windows 7 I'm having problems disconnecting from individual wireless connections. When I click 'Disconnect' from the connection manager window in the bottom right corner of the screen, nothing happens at all. I've tried this on several different connections and none of them work. I'm using: Intel(R) Wireless WiFi Link 4965AGN
View 1 Replies
View Related
Dec 11, 2012
where I can get a list of show command for individual platforms?
For example a list of show commands for cisco GSR 12000?
View 2 Replies
View Related
May 27, 2013
Best practices for an ASA5520. I'm currently running a pair of these as internal firewall for my organization, and have about 750 rules dictating traffic. A lot of the rules are for individual ports to specific server(s), some of them having 50+ ports opened. For example, Exchange has about 115 ports opened right now, anywhere from port 25 to 55000.
My question is that would it be better (faster, less strain on the ASA) to open a port range, (ie 52000-55000) or would the individual ports (ie: 52112, 52336, 52698,53441,53495, etc...) be ok?Obviously the individual ports are much more granular for security, but I don't want to take that into consideration now. Just strictly individual ports vs ranges.
View 2 Replies
View Related
Oct 27, 2011
A client is thinking of putting in a srp527w. they get assigned a static ip on the adsl interface (165.228.204.x), and then have been assigned another block(203.39.183.x/29).how can i have it so that i am able to forward individual ports from the external ip's, to selected internal ip's.
View 1 Replies
View Related
Apr 10, 2013
I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.
View 1 Replies
View Related
Sep 9, 2012
I have restricted access to users using TCP/IP using cisco 1841 router in my organization.
I need to permit some sites for users which are part of work..
The issue here is I cannot ping to the site but able to browse to that site when having internet access, i have permitted range the entire range of that IP's but still no luck..
url...is the site which is not pinging from internet.I have also checked the source code for the root IP but still no luck.
View 4 Replies
View Related
Mar 4, 2011
I have a small office (7) people and I don't have Active Directory setup. I'm wondering what is the best/easiest way to setup a place on a network server for the team to connect and put files that will then be backed up. With Active Directory this used to be a snap but I don't have much experience outside that realm. Here is how I'd like it to work:1) I login to server as admin, create the individual folders that users can map to. Example: Software Downloads, Jason, Robert, Billy, Carol2) I'd like to be able to set the security on the folders to say that everyone can view certain one but Jason can't view Roberts folder etc.
View 1 Replies
View Related
Jun 19, 2012
I am wondering if there is a method to redirect particular URLs to individual real servers in a server farm.Scenario: We have an url which is setup on our ACE4710s (A3 2.4) to load balancer to a particular server farm as per standard setup i.e.Customers access [URL] on an external VIP, this is then load balanced to a server farm "SF_WEBSITE" consisting of 2 real servers "Server_A" and "Server_B". Nothing difficult in this set up. However, I have eeen asked if it is possible to redirect certain urls to individual servers within the server farm "SF_WEBSITE": e.g.
Action 1 - Customers access [URL] is redirected to "Server_A" only
Action 2 - Customers access [URL] is redirected to "Server_B" only
Default Action - Customer access [URL] anything else is redirected to server farm "SF_WEBSITE" and is load balanced between "Server_A" and "Server_B"
The Standard Class Maps and Policy would be something like:
policy-map type loadbalance first-match SLB_WEBSITE
class class-default
serverfarm SF_WEBSITE
Where I thought I would need something like:
class-map type http loadbalance match-all CMAP_AREA1
description CMAP used to capture specific URL for area 1
2 match http url /area1
class-map type http loadbalance match-all CMAP_AREA2
description CMAP used to capture specific URL for area 2
2 match http url /area2
[code]...
I think the above method is ok for 1 instance, but if it test successfully, my company would want to to roll this out across dozens of server farm configurations each consisting of numerous real servers, which will make the administration and implementation time overheads massive, not to mention complicating and lengthening the configuration.
View 7 Replies
View Related
