I'm a C# programmer and as part of my software I need to monitor some Cisco Catalyst 3560V2 24 switches using SNMP (By reading MIB/S data).Apparently this switch supports more than 50 different MIBs.My question is which MIB/MIBS contains general health data (parameters) that may determine if the switch is OK, Degraded or Malfunctioned.
View 0 RepliesI have a VIP, which is listening on port 8312 in ACE LB and NO probes attached to it. In this scenario how does the ACE module perform the health monitoring ?
View 4 Replies View RelatedWe currently have a few 5505s installed at client sites which are connected via s2s ipsec VPN to our datacenter's 5510. We are using Nagios to monitor the local data center and remote client infrastructure (over the VPNs) which has been working well.
We would like to also monitor the remote 5505s using SNMP over the s2s tunnels but it doesn't seem to be working, the connection is timing out. We've configured the remote 5505s with the same snmp statement we used on the 5510 (snmp-server host inside <remote datacenter IP> poll community ***** version 2c) yet the Nagios SNMP check cannot connect to the remote 5505s. We've also tried the command using 'outside' without any luck, not sure how to get SNMP to route over the VPN.
I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies View RelatedI am trying to add ACS 1121 (ver 5.3) to monitoring and seems that MIB are missing. Need MIB for this device which I can use in monitoring tool.
View 1 Replies View Related how snmp monitoring works when we have WLC in the networking.Before the WLC 5508 instalation, we had the Nagios monitoring each Access Point in the networking. Today, the Nagios still monitoring the networking, but the Nagios cannot get the same information of the APs (CPU, status interface, memory, etc).Now, the WLC controls each AP, the IP address, netmask, community (of all AP) are the same before the WLC instalation. I have tried to configure the SNMP information in Management>>SNMP>>Communities, but these configuration are from WLC and not from each AP.
How can I configure the SNMP setting in my AP to still use the Nagios to monitoring the networking?
I have 5 installations of ACS appliances (ACS 1121 running ACS 5.3). Is there a way to monitor them via SNMP? The AD client keeps dying on one of them, and even with the newest patch it's not up. Also, i want to monitor them up/down, CPU, memory... basic network monitoring to make sure my devices are healthy.
Any one know if that can be configured? I figured i'd ask here before opening a TAC.
I am building a few 3750 stacks, I want to be able to poll/monitor each individual switch in the stack but as it only has 1 ip associated with the stack how can I do this. I am polling the uplink interfaces but as I only have uplinks on the top and bottom switch I am blind to a switch going down in the middle of the stack.
View 4 Replies View RelatedI am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
View 2 Replies View RelatedI was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
I have two 6509E's configured with VSS. In this configuration, is it possible to monitor the CPU and memory of each switch independently using SNMP?
View 1 Replies View RelatedI'm running 12.2(33)SXJ1 on a 6500 with several IPv6 BGP peers. Is there any way to monitor the BGP status of IPv6 peers? I've been through the BGP4 mib and cant seem find a way to check the status of IPv6 peers.
View 4 Replies View RelatedWe have C7206VXR NPE-G2 platform with transceiver which support DOM.Could we monitor DOM tx/rx level statistic through snmp for 7206 platform?In CLI result of command "sh interf GigabitEthernet0/1 transceiver" give some information.We tried search for some MIB In "MIB locator" on cisco.com.
View 2 Replies View RelatedIs temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies View RelatedI am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies View RelatedI'm currently implementing Microsoft System Center 2012 Operations Manager, the curent stage of the project is to add the network devices to SCOM via SNMP in order to monitor them, I am able to add them all and monitor; however, my ASA 5510, although SCOM discovers the ASA via SNMP and adds it to the network monitoring list, it loses SNMP connectivy every 30 minutes, and 15 later it reconnect with SCOM, then after another 15 minutes it loses the connection again, and so on and so for.
View 1 Replies View RelatedHow to configure SLA monitoring in 3560 switch. I have 2 DSL links terminating in switch and want to do WAN failover. I know how to do in ASA and router. I found IP SLA and track commands on switch but don't know exactly how to use them.
View 2 Replies View RelatedI'm working with two Catalyst 2960 switches and I would like to know if there is a way to monitor bandwidth on individual ports. Ideally I would like to have one graph showing a bandwidth usage reading on each port. I tried using the Network Assistant to accomplish this, but I was only able to view one port at a time. I also tried using a traffic graphing program from Paessler, but a MIB file is needed to allow the program to connect to the switch. When I ran a search on the network management page the 2960 was not on the list for MIB supported products. Is this type of graph possible to do?
View 2 Replies View RelatedI have a device Cat 3560. I have defined the SNMP Community Strings as shown in the config. But I Add the device in "CA Spectrum" it fails.The device responds on ICMP protocol but fails on SNMP protocol. The device is directly accessable through directly connected switch. [code]
View 2 Replies View RelatedI need to implement a "Spanning Tree Status" view on my NMS and I would like to use SNMP. I'm running Rapid Per-VLAN Spanning Tree Protocol on 3560-E (WS-C3560E-24TD) with IOS 12.2(55)SE.Using the ciscoStpExtensionsMIB MIB (CISCO-STP-EXTENSIONS-MIB) I see the stpxRSTPPortRoleTable table, which contains the stpxRSTPPortRoleValue value, and I think it could be fine for my job.The problem is that this table uses an index based on the standard dot1dBridge.1.4 table (dot1dBasePortTable) that does not report some interfaces: [code]I think the dot1dBasePortTable does not include those interfaces (5, 7, 8) where I do not run standard STP, but I need the dot1dBasePortEntry entries because I have to use them in order to get the interface ID (values like 10109, 10110, 10111).
View 0 Replies View Relatedi have 3560 switch located in warehouse environments . i need to monitor the temperate of this switch . i am looking for OID value that serves this purpose .
kindly provide me how to look for all OID that give me real time status for FAN .. CPU UTILIZATION ...TEMPERATURE ...OR ANY MAJOR EVENT THAT CAN DISRUPT MY PRODUCT IN .
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
I would like to be able to query the dot1dStpPortState obect on the Catalyst 2960-S on our LAN . Im running firmware c2960s-universalk9-mz.122-55.SE2.bin and according to the Cisco SNMP Object Navigator the object is supported (via the BRIDGE-MIB).However when i query using snmpwalk from my workstation :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 I receive and error .SNMPv2-SMI::mib-2.17.2.15.1.3 = No Such Instance currently exists at this OID For the sake of comparison, querying our 4700 :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 returns (as expected, cropped)
SNMPv2-SMI::mib-2.17.2.15.1.3.1 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.3 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.40 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.67 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.104 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.257 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.258 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.259 = INTEGER: 5
Is there some special configuration i need to do on our 2960's. The only snmp related settings i can see in the running config is snmp-server community. In this case :
snmp-server community bic-zua-ro RO
I have NM-AIR-WLC6-K9 in Cisco 2821. Is there opprotunity to retreive configuration via SNMP as from Cisco Catalyst 2960?
View 1 Replies View RelatedI recently picked up a Catalyst 2960G and am trying to get SNMP management working over IPv6. I have the IP Address set to the local link, and can successfully ping and telnet to the switch (so the network can get traffic to and from the switch). However, SNMP packets just seem to disappear. I am running WireShark on my machine, and I see the packets go out to the proper IP, but nothing comes back. When I check "sho ipv6 traffic", I can see where there are UDP packets that are received, but, again, none going out. Also, when I run "sho snmp", all of the packet counts are 0.
Here are some relavant snipets from my "sho run":
interface Vlan1
no ip address
no ip route-cache
ipv6 enable
[code]....
Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View Relatedwhich models of HP ProCurve or Dell PowerConnect support 64-bit IF-MIB counters, or for that matter any other manufacturer (Zyxel?) (snmpv2 or v3, OID .1.3.6.1.2.1.31.1.1.1.6)I believe pretty much any Cisco Catalyst above a 2950 do, however don't believe any of the SG series do. I realize I could pick up a 2960G for $1500-2k and be good to go, but I forsee a larger switch purchase in the future, but still could use a switch in the meantime that was able to allow accurate monitoring of closet uplink bandwidth?
View 1 Replies View RelatedI have a Catalyst Switch 6000. Inoticed that after the execution of the job inventory in LMS, and after the snmp queries reached the equipement, the cpu value reached 98-99 % due to the process : PDU DISPATCHER (what’s it ?)
I have also a script running in the switch to observe the differents logs. For exemple, when high cpu is obtained, the message bellow appear :
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
....
I want to upgrade a Catalyst 3560-48PS to the last IOS.I get an errormessage stating that there is insufficient space in flash: I have deleted all files in flash - but I still get the same error message. According to the documentation there should be enough memory. Messages are pasted below:
Switch#dir
Directory of flash:/
No files in directory
15998976 bytes total (15997952 bytes free)
Switch#archive download-sw tftp://192.168.9.13/c3560-ipservicesk9-tar.122-55.SE.tar
Loading c3560-ipservicesk9-tar.122-55.SE.tar from 192.168.9.13 (via Vlan9): !!!!!!!
[OK - 15964160 bytes]
Loading c3560-ipservicesk9-tar.122-55.SE.tar from 192.168.9.13 (via Vlan9): !!!!!!!!
examining image...
extracting info (109 bytes)
[code]....
Error: There is insufficient space in flash: to install the required
Error: image. Clean up some old images, and try again.
We have a IP-phone system connected to port 1 on a 3560 switch, the phone system tags traffic with dscp. The switch uplink is on port 24.
Is this configuration correct:
interface 1:
auto qos trust
interface 24:
priority-queue out
I have purchased two catalyst 3560 switches (with 24 interfaces) on Ebay to prepare for ccnp switch exam. It would be great if I have 4 switches. Is it any possibillity to create two logical switches from one? I mean, not by assigning interfaces to different vlans?
View 1 Replies View RelatedI have installed a Catalyst 3560 as my internal router. I have created 4 vlans to route the traffic.
Here are the interface "show run"
vlan internal allocation policy ascending
!
interface FastEthernet0/1
switchport access vlan 2
switchport mode access
spanning-tree portfast
[code].....
I have been getting notifications of large packet loss and latency for itnernal traffic going to servers. I have a simple setup of nagios who pings servers and will notify me of large packet loss or complete packet loss. I have implemented this L3 switch a few hours ago, I am currently running a constant ping to my servers, but I am not niticing packet loss right now.This packet loss happened 4 time spans within the last hour of many large packet losses to all my servers within all subnets. It is now stopped.
I am not sure why this would be happening, the predessor of the internal router was just a normal linux box with 3 NICs on it. Nothing crazy going on since the business is closed.