Cisco :: Catalyst 2960 Is There Opportunity To Backup WLC6 Via SNMP
Mar 2, 2012I have NM-AIR-WLC6-K9 in Cisco 2821. Is there opprotunity to retreive configuration via SNMP as from Cisco Catalyst 2960?
View 1 Replies
ADVERTISEMENT
Cisco :: SNMP / Query Dot1dStpPortState On Catalyst 2960-S
Dec 10, 2012I would like to be able to query the dot1dStpPortState obect on the Catalyst 2960-S on our LAN . Im running firmware c2960s-universalk9-mz.122-55.SE2.bin and according to the Cisco SNMP Object Navigator the object is supported (via the BRIDGE-MIB).However when i query using snmpwalk from my workstation :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 I receive and error .SNMPv2-SMI::mib-2.17.2.15.1.3 = No Such Instance currently exists at this OID For the sake of comparison, querying our 4700 :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 returns (as expected, cropped)
SNMPv2-SMI::mib-2.17.2.15.1.3.1 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.3 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.40 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.67 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.104 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.257 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.258 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.259 = INTEGER: 5
Is there some special configuration i need to do on our 2960's. The only snmp related settings i can see in the running config is snmp-server community. In this case :
snmp-server community bic-zua-ro RO
Cisco Switches :: 300 Series Snmp Backup
Aug 22, 2011we are trying to do an automatic backup of our switches config trough snmp.my script can easily backup cisco 2950-2960-3550-3560 using snmp.but I dont know the mib to use to backup the cisco small business serie 300 switches.
View 6 Replies View RelatedCisco :: Monitoring Catalyst 3560 Health Using MIB / SNMP
May 23, 2011I'm a C# programmer and as part of my software I need to monitor some Cisco Catalyst 3560V2 24 switches using SNMP (By reading MIB/S data).Apparently this switch supports more than 50 different MIBs.My question is which MIB/MIBS contains general health data (parameters) that may determine if the switch is OK, Degraded or Malfunctioned.
View 0 Replies View RelatedCisco Security :: SNMP OID For VLAN And Port 2960 Series
Jan 19, 2011Cisco Catalyst 2960 series,i want do a SNMP request over OID. When the output should be like this: Portnumber and VlanID. Is there a OID for this output?
View 1 Replies View RelatedCisco Switching/Routing :: 2960 / 3560 - OID For Reload Via SNMP?
Jul 10, 2012I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
Cisco :: Catalyst 2960G / Get SNMP Management Working Over IPv6?
Jul 20, 2011I recently picked up a Catalyst 2960G and am trying to get SNMP management working over IPv6. I have the IP Address set to the local link, and can successfully ping and telnet to the switch (so the network can get traffic to and from the switch). However, SNMP packets just seem to disappear. I am running WireShark on my machine, and I see the packets go out to the proper IP, but nothing comes back. When I check "sho ipv6 traffic", I can see where there are UDP packets that are received, but, again, none going out. Also, when I run "sho snmp", all of the packet counts are 0.
Here are some relavant snipets from my "sho run":
interface Vlan1
no ip address
no ip route-cache
ipv6 enable
[code]....
Cisco Infrastructure :: Temperature Status From 2960 Switch Using SNMP Not Working
Sep 18, 2012WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
Cisco :: 2960 / 3750S / 3750X / 6504S - SNMP Trap Configuration
Sep 10, 2012I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer. I have Cisco 6504's running IOS on the Distribution and Core layers. I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it. I would like to have:
1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.
Cisco Switching/Routing :: 2960 - Enable Snmp For Switch Port
Dec 18, 2011i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View RelatedCisco Application :: Possible To Modify Configure With Snmp On Ace Module Like Others 6500 Catalyst
Apr 12, 2012Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View RelatedCisco Catalyst 2950 - GigE Switches With 64bit IF-MIB SNMP Counters?
Oct 18, 2011which models of HP ProCurve or Dell PowerConnect support 64-bit IF-MIB counters, or for that matter any other manufacturer (Zyxel?) (snmpv2 or v3, OID .1.3.6.1.2.1.31.1.1.1.6)I believe pretty much any Cisco Catalyst above a 2950 do, however don't believe any of the SG series do. I realize I could pick up a 2960G for $1500-2k and be good to go, but I forsee a larger switch purchase in the future, but still could use a switch in the meantime that was able to allow accurate monitoring of closet uplink bandwidth?
View 1 Replies View RelatedCisco :: Catalyst Switch 6000 - Process Snmp PDU Dispatcher Causes High CPU Value
Mar 28, 2012I have a Catalyst Switch 6000. Inoticed that after the execution of the job inventory in LMS, and after the snmp queries reached the equipement, the cpu value reached 98-99 % due to the process : PDU DISPATCHER (what’s it ?)
I have also a script running in the switch to observe the differents logs. For exemple, when high cpu is obtained, the message bellow appear :
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
....
Cisco Switching/Routing :: 2960 - Using PAGP As Backup For Wireless Link With Another One
Jul 7, 2012use PAGP as backup for wireless link with another wireless link.
__WiFi________
PC-------Switch 1 Switch2---------- PC
__WiFi________
We are using 2960 series and from this reason we cant use L3 PAGP I dont know how is PAGP working. If it is checkung port status (UP/Down) or there are some specific L2 packet between etherchannel ports in group?
Cisco :: Snmp Oids For Command Show Counters Interface Intx / Y Delta On Catalyst 6500
May 23, 2011I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies View RelatedCisco :: LMS 4.0 IOS Upgrade For Catalyst 2960?
Feb 16, 2011I tried to update Cisco Catalyst 2960 Switches through LMS 4.0
But LMS won't update the 2960 because there is not enough Flash Space on the device. The 2960 shoud have 32MB but a dir flash shows this
27998208 bytes total (15343104 bytes free)
A manual update on the switch is working perfect. Is this a bug or if there is a workaround to make LMS 4.0 working?
Cisco WAN :: Configuring NAT On Catalyst 2960
Jan 4, 2011I've just made a purchase for a Cisco 2960 8 port switch ( Exact model: WS-C2960PD-8TT-L ), I reckon this is what I need to set up my network, so far I've gone through the Express Set-up and configured it through there with no problems. I've set up the hardware in the following manner:
-Internet Modem
>Port 8 on Switch
->Port 1 on Switch goes to 1252 Cisco AP
->Port 2 on Switch goes to Linksys VOIP home Router
I let it start up and can connect to the internet through the AP, and through the router. (I'm posting through the AP-Switch set-up right now.) However, once I connect to the AP with a second client. It refuses to let the second client connect/not give an internet connection, as it would a direct connection to the modem.I'm going to assume this is due to NAT not being configured through the command line on the switch yet.
Cisco WAN :: Manage Catalyst 2960 With CNA
Jan 23, 2011i have got 5 catalyst :
Cisco Catalyst WS-C2960G-24TS-S
version 12.2 (53) SE
Image : C2960S-UNIVERSALK9-M
and i can 't configure the switch with Cisco Network Assistant. I have got this error : "unsupported device".
it is not possible to configure this model with CNA ?
Cisco Switching/Routing :: Catalyst 2950 - Release For Snmp-server Enable Traps Errdisable Command?
May 16, 2013We have a catalyst 2950 switch running:
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)
This release doesnt have the snmp-server enable traps errdisable command.
Where to look on the cisco site for the next available release for me that would have this command in place?
Cisco :: Bandwidth Monitoring On A Catalyst 2960
Oct 23, 2007I'm working with two Catalyst 2960 switches and I would like to know if there is a way to monitor bandwidth on individual ports. Ideally I would like to have one graph showing a bandwidth usage reading on each port. I tried using the Network Assistant to accomplish this, but I was only able to view one port at a time. I also tried using a traffic graphing program from Paessler, but a MIB file is needed to allow the program to connect to the switch. When I ran a search on the network management page the 2960 was not on the list for MIB supported products. Is this type of graph possible to do?
View 2 Replies View RelatedCisco WAN :: Radius Authentication On Catalyst 2960?
Feb 25, 2013I have a problem with radius authentication on catalyst 2960 with freeradius as radius-server. The Catalyst is behind a HP5412zl layer3-switch. The rest of the network are hp-layer2 switches, which do radius authentication to the same radius server. The ios on the catalyst is c2960-lanbasek9-mz.150-1.SE3. Apparently there are no requests made to the radius-server, since I dont see any requests coming in. Port 0/7 is voice port with laptop behind , /port 0/8 access-port with laptop directly connected.
config :
aaa new-model
aaa authentication dot1x default group radius
dot1x system-auth-control
!
!
!
interface FastEthernet0/1
[code]....
Cisco :: Catalyst 2960 Series 8 Port Switch?
Oct 18, 2012I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies View RelatedCisco :: Catalyst 2960 Unable To Add Members To Community
Mar 27, 2013I try to add a Catalyst 2960 to Cisco Network Assistant, I get the prompt for password but I get a "Authentication failed". I use the same login / password for telnet that works fine. Http admin page is reachable but I cannot login with the "admin" account.
View 2 Replies View RelatedCisco Switching/Routing :: Can't SSH Into New Catalyst 2960 Switch
Jun 13, 2012I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
Cisco :: Catalyst 2960 Two Macs On One Port Need Two Vlans?
Aug 7, 2011I have a device that does ip audio on one mac address and managagement is on another mac address. Both of these mac addresses come from one NIC on the device. We need to split these two traffic paths into two different vlans.How can I program this switch to sperate the different traffic into two vlan's based on mac address on one interface?
View 2 Replies View RelatedCisco Switching/Routing :: SFP Port On Catalyst 2960 S?
Mar 18, 2013I have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
Cisco Infrastructure :: Can't Upload By Tftp On Any Catalyst 2960
Dec 17, 2012i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst 2960 Switch Qos
Aug 20, 2012i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
Cisco Switching/Routing :: Can't SSH Into New Catalyst 2960-S Switch
Apr 29, 2012I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
Cisco :: Network Assistant MAC Search In Catalyst 2960
Feb 28, 2011Since I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
Cisco Switching/Routing :: How To Stack Catalyst 2960
Dec 1, 2012How would I go about stacking 4 Cisco Catalyst 2960-48PST-L switches? The one switch needs to accept a fiber connection from a distribution switch. Do I have to buy flexstack module and cables? If so where does the module go on the switch? If this switch cannot do this set up, any other switch I should look at.
View 6 Replies View RelatedCisco Switching/Routing :: Catalyst 2960 - How To Configure With CLI
Sep 20, 2012Will catalyst2960 supports SSH, and how to configures with CLI.
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst 2960 IOS Upgrade
Apr 9, 2012I need to upgrade a Catalyst IOS, but I got a bit confused. The catalyst is currently running "c2960-lanbase-mz.122-35.SE5.bin", but I want to upgrade to "c2960-lanbasek9-mz.122-35.SE5.bin", in order to enable ssh. [code] What are the appropriate steps in order to upgrade to "c2960-lanbasek9-mz. 122- 35. SE5.bin". I have downloaded the tar file (c2960-lanbasek9-tar.122-35.SE5.tar)
1) Do I have to delete the old directory (drwx 192 Mar 1 1993 02:07:21 +02:00 c2960-lanbase-mz.122-35.SE5)?
2) Are these the correct steps to download and extract the IOS?
3) Where will the tar files be extracted? Will an new directory be made or do I have to make one manually?
