i have got 5 catalyst :
Cisco Catalyst WS-C2960G-24TS-S
version 12.2 (53) SE
Image : C2960S-UNIVERSALK9-M
and i can 't configure the switch with Cisco Network Assistant. I have got this error : "unsupported device".
it is not possible to configure this model with CNA ?
I would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.
View 3 Replies View RelatedI have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
I have more than 20 Cisco switches in my office which is basically a soap manufacturing factory. The switches include Cisco 2950, 2960, 3560, 3750 etc. We have routers also which include 2821, 2951 etc. We also have Cisco WLC 2125 and LAP 1262 series. Sometimes all these devices management comes very tough to us.
We need to log on to different devices for troubleshooting/network management which sometimes becomes very tough to us. So I wonder if there any Cisco applications or tools by which we can centrally manage all these devices.
For my Lan, I have created two Vlan; Vlan 10 = for Users and Vlan 20 = For Database Servers,There are 15 Lan computer/laptop and 5 SQL database server (Dell Server) connected through same 24 port cisco 2960 switch. Means, 15 + 5 port occupied.
I have applied access list on cisco switch to restrict communication between vlan 10 and vlan 20.But My main purpose to create two Vlan is not for any kind of communication or restriction. My main Purpose is that Users traffic do not distrub or choke or affect the Database servers. then what will i need to do for that is VLAN Concept is sufficient for my concern OR I will need to buy seperate Cisco Switch to connect 5 database servers OR Else ?
I tried to update Cisco Catalyst 2960 Switches through LMS 4.0
But LMS won't update the 2960 because there is not enough Flash Space on the device. The 2960 shoud have 32MB but a dir flash shows this
27998208 bytes total (15343104 bytes free)
A manual update on the switch is working perfect. Is this a bug or if there is a workaround to make LMS 4.0 working?
I've just made a purchase for a Cisco 2960 8 port switch ( Exact model: WS-C2960PD-8TT-L ), I reckon this is what I need to set up my network, so far I've gone through the Express Set-up and configured it through there with no problems. I've set up the hardware in the following manner:
-Internet Modem
>Port 8 on Switch
->Port 1 on Switch goes to 1252 Cisco AP
->Port 2 on Switch goes to Linksys VOIP home Router
I let it start up and can connect to the internet through the AP, and through the router. (I'm posting through the AP-Switch set-up right now.) However, once I connect to the AP with a second client. It refuses to let the second client connect/not give an internet connection, as it would a direct connection to the modem.I'm going to assume this is due to NAT not being configured through the command line on the switch yet.
I'm working with two Catalyst 2960 switches and I would like to know if there is a way to monitor bandwidth on individual ports. Ideally I would like to have one graph showing a bandwidth usage reading on each port. I tried using the Network Assistant to accomplish this, but I was only able to view one port at a time. I also tried using a traffic graphing program from Paessler, but a MIB file is needed to allow the program to connect to the switch. When I ran a search on the network management page the 2960 was not on the list for MIB supported products. Is this type of graph possible to do?
View 2 Replies View RelatedI have a problem with radius authentication on catalyst 2960 with freeradius as radius-server. The Catalyst is behind a HP5412zl layer3-switch. The rest of the network are hp-layer2 switches, which do radius authentication to the same radius server. The ios on the catalyst is c2960-lanbasek9-mz.150-1.SE3. Apparently there are no requests made to the radius-server, since I dont see any requests coming in. Port 0/7 is voice port with laptop behind , /port 0/8 access-port with laptop directly connected.
config :
aaa new-model
aaa authentication dot1x default group radius
dot1x system-auth-control
!
!
!
interface FastEthernet0/1
[code]....
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies View RelatedI would like to be able to query the dot1dStpPortState obect on the Catalyst 2960-S on our LAN . Im running firmware c2960s-universalk9-mz.122-55.SE2.bin and according to the Cisco SNMP Object Navigator the object is supported (via the BRIDGE-MIB).However when i query using snmpwalk from my workstation :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 I receive and error .SNMPv2-SMI::mib-2.17.2.15.1.3 = No Such Instance currently exists at this OID For the sake of comparison, querying our 4700 :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 returns (as expected, cropped)
SNMPv2-SMI::mib-2.17.2.15.1.3.1 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.3 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.40 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.67 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.104 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.257 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.258 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.259 = INTEGER: 5
Is there some special configuration i need to do on our 2960's. The only snmp related settings i can see in the running config is snmp-server community. In this case :
snmp-server community bic-zua-ro RO
I try to add a Catalyst 2960 to Cisco Network Assistant, I get the prompt for password but I get a "Authentication failed". I use the same login / password for telnet that works fine. Http admin page is reachable but I cannot login with the "admin" account.
View 2 Replies View RelatedI'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
I have a device that does ip audio on one mac address and managagement is on another mac address. Both of these mac addresses come from one NIC on the device. We need to split these two traffic paths into two different vlans.How can I program this switch to sperate the different traffic into two vlan's based on mac address on one interface?
View 2 Replies View RelatedI have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies View Relatedi try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
Since I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
How would I go about stacking 4 Cisco Catalyst 2960-48PST-L switches? The one switch needs to accept a fiber connection from a distribution switch. Do I have to buy flexstack module and cables? If so where does the module go on the switch? If this switch cannot do this set up, any other switch I should look at.
View 6 Replies View RelatedWill catalyst2960 supports SSH, and how to configures with CLI.
View 2 Replies View RelatedI need to upgrade a Catalyst IOS, but I got a bit confused. The catalyst is currently running "c2960-lanbase-mz.122-35.SE5.bin", but I want to upgrade to "c2960-lanbasek9-mz.122-35.SE5.bin", in order to enable ssh. [code] What are the appropriate steps in order to upgrade to "c2960-lanbasek9-mz. 122- 35. SE5.bin". I have downloaded the tar file (c2960-lanbasek9-tar.122-35.SE5.tar)
1) Do I have to delete the old directory (drwx 192 Mar 1 1993 02:07:21 +02:00 c2960-lanbase-mz.122-35.SE5)?
2) Are these the correct steps to download and extract the IOS?
3) Where will the tar files be extracted? Will an new directory be made or do I have to make one manually?
Im trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
I have packet loss with QoS configured and I was wondering is it somehow connected with the QoS configured on the switch.The traffic is passing through fa0/19 and gi0/1 interfaces.
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue input bandwidth 90 10
mls qos srr-queue input threshold 1 8 16
mls qos srr-queue input threshold 2 34 66
[code]...
I have 4 Catalyst 2960 connected via Etherchannel to each other. If I plug in my notebook in one port, I see the traffic from the neighbor port. So my switch acts like a hub.. I had a look at my MAC table and saw it isn't full.
View 2 Replies View RelatedI have a problem with the time synchronization via NTP between a Catalyst 2960 and Catalyst 6509. When I configure the 6509 switch as a NTP reference on the 2960, it does not synchronize with the 6509's NTP server. There is no reachability or ACL-related issue between both switches.
As soon as I configure a second Catalyst 6509 (which is completely identical to the other 6509 and in the same subnet) as a NTP server for the 2960, the time sync with the second 6509 happens immediality.
The first 6509 switch works as a NTP reference for at least 50 other switches and routers in the network - so why not for this one more switch? I checked some "debug ntp packet" and "debug ntp events" outputs and can clearly watch the NTP requests going out of the 2960, but on the 6509 just nothing happens - no debug outputs for this specific 2960, while requests from other devices come in all the time.
Maybe you have already experienced this strange behaviour in the past or got some deeper knowledge in the Cisco NTP server implementation. I could think of some sort of "maximum client limit" in the IOS NTP server, but could not find any mechanism like this in the standard NTP specification. Eventually, you can approve that this is a IOS-specific issue.
I have NM-AIR-WLC6-K9 in Cisco 2821. Is there opprotunity to retreive configuration via SNMP as from Cisco Catalyst 2960?
View 1 Replies View RelatedI have ciscl catlyst 2960 8port switch, (flash:c2960-lanbasek9-mz.122-50.SE4/c2960-lanbasek9-mz.122-50.SE4.bin).
and in need to configure bandwidth limit for one of the port as a 1Mbps.
In an attempt to restore a Cisco IOS I deleted the file C2960-lanbasek9-mz.122-53.SE2.bin my swich
Before deleting the same was as follows:Directory of flash :/
3-rwx 12824 Mar 28 1993 21:00:37 -03:00 vlan.dat4-rwx 3096 Mar 7 2012 08:43:37 -02:00 multiple-fs5-rwx 2289 Mar 7 2012 08:43:37 -02:00 private-config.text6-rwx 7482 Mar 7 2012 08:43:37 -02:00 config.text9 drwx 192 Mar 23 2012 16:18:54 -03:00 C2960-lanbasek9-mz.122-53.SE2
32514048 bytes total (20204544 bytes free)Switch-01 #
Right now this switch as follows:
switch: dir flash:Directory of flash:/
2 drwx 64 <date> crashinfo_ext 3 -rwx 4120 <date> multiple-fs 5 -rwx 12824 <date> vlan.dat 6 -rwx 4018 <date>
[Code].....
I need to know if Cisco Switch 2960 support Netflow. If it doesn't, how do I configure the switch to enable Netflow?
View 3 Replies View RelatedI have a Catalyst 2960-S switch and a pre-standard IP Phone (Cisco 7960). When I connect the phone to the switch the switch recognizes the phone and supplies power. I would like to prevent this behaviour. ie. I would like to disable detection of pre-standard equipment. Is there a command I can issue on the 2960-S to do this? For example, on a switch from a different vendor I can issue the command: no power pre-std-detect to prevent it from detecting the 7960 phone, is there an equivalent command on the Catalyst 2960-S ?
View 3 Replies View RelatedI added Linksys RV-016 16-ports VPN Router into the connection. RV-016 supported multiple subnets.
As mentioned in [URL], D-Link DIR-615 needs to be a device which could support multiple Vlan subnets. But unluckily DIR-615 does not support multiple Vlan subnets.
Therefore I added Linksys RV-016 in the the combination of devices. As what i found in RV-016 GUI setting, it supports multiple subnets.
Purpose outline:
1. Have to create two different SSIDs.
- SSID 1 for Management (able to view all other LAN devices)
- SSID 2 for guest and staff (unable to view all other LAN devices)
2. Create two VLANs in catalyst 2960s.
3. Create two subnets in Linksys RV-016 to accept two Vlans from catalyst 2960s.
Any experience of configuring RV-016 for the mentioned purpose above?
I'm trying to create trunkports on our Catalyst 2960. I'm following this guide to configure interface fa0/1
View 4 Replies View Related