Cisco :: Network Assistant MAC Search In Catalyst 2960
Feb 28, 2011
Since I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
View 4 Replies
ADVERTISEMENT
Apr 2, 2012
why Windows Server 2008 is not a supported OS for Cisco Network Assistant?I am currently evaluating switch management solutions for use with Catalyst 2960 and 3750 series switches, and would like to be able to backup and restore configurations, as well as make configuration changes. My management Server is running Server 2008.Is Prime LMS my only option?
View 5 Replies
View Related
Feb 6, 2013
Wondering if this switch is capable of being a backbone switch for a network of about 1000+ users and if the switch can handle a sustained 30Meg of data going across it?
View 3 Replies
View Related
Jun 25, 2006
i have managed to create a community of cisco devices however although i can add the pix to the community it does not show up in the topology? HTTPS is enable. I can also access the pix via ASDM.
View 2 Replies
View Related
Dec 27, 2012
I'm experiencing considerable difficulties with CNA and my 4948E cat's. Front panel view, vLans and VTP utterly fail...and I have gone to GREAT lengths. I initially configured them all for comprehensive use in a vSphere environment. Storage switch fabric and multi-vlan guest networking. I wiped the config's across the board, factory reset all of them in an attampt to get CNA working. NO GO and it's been wildly frustrating, 80+ hrs spent with no results.
So is CNA truely compatible with the 4948e? And if so, WHAT IN THE **** AM I DOING WRONG!!?!?!?!!!!!?
Config and info:
C4948#show verCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.1(1)SG2, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Wed 24-Oct-12 02:27 by prod_rel_team
ROM: 12.2(44r)SG11C4948 uptime is 22 minutesSystem returned to ROM by reloadSystem image file is "bootflash:cat4500e-entservicesk9-mz.151-1.SG2.bin"Hobgoblin Revision 21, Fortooine Revision 1.40
Last reload reason: Reload command
[Code]...
View 11 Replies
View Related
Sep 19, 2012
CNA 5.8(1)
32 devices
When I first launch the application, it promots for CCO login information, but then tells me the username or password is invalid. I reset it once, and it appeared to work. Next time I launched the application though, it gave me the same login error and did not store any of the device credentials. This is a new install of CNA and it just has one community setup on it now. I've tried 2 different CCO accounts and they both give the same login failure. I know the passwords I'm using are correct though.
View 15 Replies
View Related
Oct 18, 2012
I'm trying to get a network of SGE2000 switches mapped into Cisco network assistant.It always comes back with the device type unknown and status unsupported device.Is there a way to fix this ? I'm using Cisco network assistant ver.5.7(6)
View 4 Replies
View Related
Feb 22, 2011
2950s work fine when upgrading the IOS using CNA. On all 2960s I get Failed to execute the command archive download-sw /overwrite /http iosFile
If I run the command using telnet and tftp server it works fine.
I have tried by deleting the old image then trying upgrade using CNA, but no luck
View 1 Replies
View Related
Sep 10, 2012
I work on photocopiers and sometimes I get an error code that's not in the service manual.[URL]contains some useful information so I use Google to search the forums for example:It has recently stopped working on my computer and another at work. Copytechnet loads breifly then windows says unable to connect to site and internet explorer closes.
View 1 Replies
View Related
Jun 21, 2011
I have a small business network computers w/a linux server. One computer was infected with viruses which I removed via kaspersky/norton/malware anti-bytes. I run windows xp professional on this computer.However I run into the following problem:
1) In my network places the documents on the server do not show as a network place-this is despite me being able to access these documents via a folder shortcut
2) After I open the network files/folders from the comp, I am unable to use the find feature because the folder is not listed under the look in drop box. I tried changing workgroups and ran into the same problem.
View 10 Replies
View Related
Jan 25, 2011
"Can't find certificate-wireless". I've applied all the suggestions. With and with out Winduh Zero Config and network adapter software. Unchecked 802.1x, changed ecryption types, modem and computer reboots, push little button on back of modem, tried two differnt makes of network adapters, confirmed correct network key typed, etc. All these things in many combinations. Great full signal, no certificate or with software installed no connectivity. Is it time to Ethernet hard wire my network? Is it the Windstream 1704 modem? Studied and tweaked the modem settings a little
View 7 Replies
View Related
Oct 22, 2012
CNA version is 7.5(6)
router: Cisco 2951
error: unable to connect
are able to connect to other switches, such as 2970 questions:
1. is there any configuration needs to be done to connect to 2951 though CNA?
2. is 2951 supported device in CNA?
View 2 Replies
View Related
May 16, 2013
With my brand new Cisco 3850 Switch, I got it configured with a LAN IP. Then, on my PC I opened up Cisco Network Assistant (version 5.8.5.1 which supports the 3850). I went to add the 3850 to the community by discovering the device, and was prompted with the user/pass box. The password I set was not allowing me to connect, and I realized it's because a username was required and I had not set up a username on the switch. So, I then configured an admin user with level 15 privileges on the switch. However, now when in CNA I try to add the 3850 to the community, it doesn't even prompt me for user/pass, it just says "unable to connect".
What do I need to do to add this 3850 to my community?
View 16 Replies
View Related
Feb 16, 2012
I have a Cisco 2948G switch that I am trying to communicate to through this program. It has both an IP address and is hooked up through a cable. I can get Cisco Network Assistant to come up and ask for it's Username and Password, and that it is where I am stuck! I have no clue as to what to put in there as a username and password? I do have a password setup on the switch to login in to it during terminal mode, but that is it.
View 1 Replies
View Related
Oct 21, 2012
I have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
View 2 Replies
View Related
Mar 22, 2011
Does the latest version of the Network Assistant support the AP1131AG / AP1131G model?
From the "supported device list" documentation it seems yes, but I've tried to import them into the map and received the message indicating that is not supported as a device...AP1242AG/1242G are not having this problem.
View 2 Replies
View Related
Nov 6, 2012
Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?
View 3 Replies
View Related
Dec 30, 2012
I am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies
View Related
Feb 16, 2011
I tried to update Cisco Catalyst 2960 Switches through LMS 4.0
But LMS won't update the 2960 because there is not enough Flash Space on the device. The 2960 shoud have 32MB but a dir flash shows this
27998208 bytes total (15343104 bytes free)
A manual update on the switch is working perfect. Is this a bug or if there is a workaround to make LMS 4.0 working?
View 2 Replies
View Related
Jan 4, 2011
I've just made a purchase for a Cisco 2960 8 port switch ( Exact model: WS-C2960PD-8TT-L ), I reckon this is what I need to set up my network, so far I've gone through the Express Set-up and configured it through there with no problems. I've set up the hardware in the following manner:
-Internet Modem
>Port 8 on Switch
->Port 1 on Switch goes to 1252 Cisco AP
->Port 2 on Switch goes to Linksys VOIP home Router
I let it start up and can connect to the internet through the AP, and through the router. (I'm posting through the AP-Switch set-up right now.) However, once I connect to the AP with a second client. It refuses to let the second client connect/not give an internet connection, as it would a direct connection to the modem.I'm going to assume this is due to NAT not being configured through the command line on the switch yet.
View 4 Replies
View Related
Jan 23, 2011
i have got 5 catalyst :
Cisco Catalyst WS-C2960G-24TS-S
version 12.2 (53) SE
Image : C2960S-UNIVERSALK9-M
and i can 't configure the switch with Cisco Network Assistant. I have got this error : "unsupported device".
it is not possible to configure this model with CNA ?
View 3 Replies
View Related
Jun 23, 2011
I have two WS-C2950G-24-EI switches each of which were running software version 12.1(22)EA2-C2950-I6Q4L2-M. Both swtiches were viewable from Network Assistant version 5.6(3) and part of a community. I then updated the software on one of the switches to 12.1(22)EA14, and now Network Assistant will not add the new updated device to the community and gives an error of "WS-C2950G-24-EI is not supported as community member". Is the latest version (12.1(22)EA14) not supported by Network Assistant? The release notes indicate the Minimum Software Release is 12.1(22)EA4.
View 1 Replies
View Related
Oct 23, 2007
I'm working with two Catalyst 2960 switches and I would like to know if there is a way to monitor bandwidth on individual ports. Ideally I would like to have one graph showing a bandwidth usage reading on each port. I tried using the Network Assistant to accomplish this, but I was only able to view one port at a time. I also tried using a traffic graphing program from Paessler, but a MIB file is needed to allow the program to connect to the switch. When I ran a search on the network management page the 2960 was not on the list for MIB supported products. Is this type of graph possible to do?
View 2 Replies
View Related
Feb 25, 2013
I have a problem with radius authentication on catalyst 2960 with freeradius as radius-server. The Catalyst is behind a HP5412zl layer3-switch. The rest of the network are hp-layer2 switches, which do radius authentication to the same radius server. The ios on the catalyst is c2960-lanbasek9-mz.150-1.SE3. Apparently there are no requests made to the radius-server, since I dont see any requests coming in. Port 0/7 is voice port with laptop behind , /port 0/8 access-port with laptop directly connected.
config :
aaa new-model
aaa authentication dot1x default group radius
dot1x system-auth-control
!
!
!
interface FastEthernet0/1
[code]....
View 1 Replies
View Related
Oct 18, 2012
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies
View Related
Dec 10, 2012
I would like to be able to query the dot1dStpPortState obect on the Catalyst 2960-S on our LAN . Im running firmware c2960s-universalk9-mz.122-55.SE2.bin and according to the Cisco SNMP Object Navigator the object is supported (via the BRIDGE-MIB).However when i query using snmpwalk from my workstation :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 I receive and error .SNMPv2-SMI::mib-2.17.2.15.1.3 = No Such Instance currently exists at this OID For the sake of comparison, querying our 4700 :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 returns (as expected, cropped)
SNMPv2-SMI::mib-2.17.2.15.1.3.1 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.3 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.40 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.67 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.104 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.257 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.258 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.259 = INTEGER: 5
Is there some special configuration i need to do on our 2960's. The only snmp related settings i can see in the running config is snmp-server community. In this case :
snmp-server community bic-zua-ro RO
View 3 Replies
View Related
Mar 27, 2013
I try to add a Catalyst 2960 to Cisco Network Assistant, I get the prompt for password but I get a "Authentication failed". I use the same login / password for telnet that works fine. Http admin page is reachable but I cannot login with the "admin" account.
View 2 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
Aug 7, 2011
I have a device that does ip audio on one mac address and managagement is on another mac address. Both of these mac addresses come from one NIC on the device. We need to split these two traffic paths into two different vlans.How can I program this switch to sperate the different traffic into two vlan's based on mac address on one interface?
View 2 Replies
View Related
Mar 18, 2013
I have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
View 11 Replies
View Related
Dec 17, 2012
i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies
View Related
Aug 20, 2012
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
View 3 Replies
View Related
Apr 29, 2012
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
View 5 Replies
View Related
