Cisco Switching/Routing :: 2948G - Can't Get Network Assistant To Connect
Feb 16, 2012
I have a Cisco 2948G switch that I am trying to communicate to through this program. It has both an IP address and is hooked up through a cable. I can get Cisco Network Assistant to come up and ask for it's Username and Password, and that it is where I am stuck! I have no clue as to what to put in there as a username and password? I do have a password setup on the switch to login in to it during terminal mode, but that is it.
View 1 Replies
ADVERTISEMENT
May 16, 2013
With my brand new Cisco 3850 Switch, I got it configured with a LAN IP. Then, on my PC I opened up Cisco Network Assistant (version 5.8.5.1 which supports the 3850). I went to add the 3850 to the community by discovering the device, and was prompted with the user/pass box. The password I set was not allowing me to connect, and I realized it's because a username was required and I had not set up a username on the switch. So, I then configured an admin user with level 15 privileges on the switch. However, now when in CNA I try to add the 3850 to the community, it doesn't even prompt me for user/pass, it just says "unable to connect".
What do I need to do to add this 3850 to my community?
View 16 Replies
View Related
Dec 30, 2012
I am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies
View Related
Feb 15, 2012
I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong.
View 3 Replies
View Related
Dec 10, 2012
I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong. This switch runs CatOS, not IOS.When power is applied to the switch, the fans turn on as normal, but no LEDs are lit on the front. There are green LEDs lit next to the jumpers inside, but that is all. I am not able to get any response from it on the console at all anymore.The LEDs that are lit green inside are labeled "CR5" and CR6".
View 2 Replies
View Related
May 9, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop :I know that the solution would be to download a new valid image from tftp via the rommon prompt but what i dont undertand is why i cant access the rommon prompt. It justs boots with the message above in a loop
View 0 Replies
View Related
Oct 25, 2012
I am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
View 5 Replies
View Related
Oct 22, 2012
CNA version is 7.5(6)
router: Cisco 2951
error: unable to connect
are able to connect to other switches, such as 2970 questions:
1. is there any configuration needs to be done to connect to 2951 though CNA?
2. is 2951 supported device in CNA?
View 2 Replies
View Related
Apr 26, 2012
Looking to setup a backup router for our disaster recovery plan. We currently have a Cisco 877W that was setup by our ISP. I can log into the device with Telnet and a console cable, but I am not good using IOS commands, so I would like to use CCA. Unfortunatley, I cannot access the router using the software. I assume something is disabled in the config. Like HTTP or something.
View 1 Replies
View Related
Jun 25, 2006
i have managed to create a community of cisco devices however although i can add the pix to the community it does not show up in the topology? HTTPS is enable. I can also access the pix via ASDM.
View 2 Replies
View Related
Dec 27, 2012
I'm experiencing considerable difficulties with CNA and my 4948E cat's. Front panel view, vLans and VTP utterly fail...and I have gone to GREAT lengths. I initially configured them all for comprehensive use in a vSphere environment. Storage switch fabric and multi-vlan guest networking. I wiped the config's across the board, factory reset all of them in an attampt to get CNA working. NO GO and it's been wildly frustrating, 80+ hrs spent with no results.
So is CNA truely compatible with the 4948e? And if so, WHAT IN THE **** AM I DOING WRONG!!?!?!?!!!!!?
Config and info:
C4948#show verCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.1(1)SG2, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Wed 24-Oct-12 02:27 by prod_rel_team
ROM: 12.2(44r)SG11C4948 uptime is 22 minutesSystem returned to ROM by reloadSystem image file is "bootflash:cat4500e-entservicesk9-mz.151-1.SG2.bin"Hobgoblin Revision 21, Fortooine Revision 1.40
Last reload reason: Reload command
[Code]...
View 11 Replies
View Related
Sep 19, 2012
CNA 5.8(1)
32 devices
When I first launch the application, it promots for CCO login information, but then tells me the username or password is invalid. I reset it once, and it appeared to work. Next time I launched the application though, it gave me the same login error and did not store any of the device credentials. This is a new install of CNA and it just has one community setup on it now. I've tried 2 different CCO accounts and they both give the same login failure. I know the passwords I'm using are correct though.
View 15 Replies
View Related
Oct 18, 2012
I'm trying to get a network of SGE2000 switches mapped into Cisco network assistant.It always comes back with the device type unknown and status unsupported device.Is there a way to fix this ? I'm using Cisco network assistant ver.5.7(6)
View 4 Replies
View Related
Feb 28, 2011
Since I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
View 4 Replies
View Related
Feb 22, 2011
2950s work fine when upgrading the IOS using CNA. On all 2960s I get Failed to execute the command archive download-sw /overwrite /http iosFile
If I run the command using telnet and tftp server it works fine.
I have tried by deleting the old image then trying upgrade using CNA, but no luck
View 1 Replies
View Related
Oct 21, 2012
I have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
View 2 Replies
View Related
Mar 22, 2011
Does the latest version of the Network Assistant support the AP1131AG / AP1131G model?
From the "supported device list" documentation it seems yes, but I've tried to import them into the map and received the message indicating that is not supported as a device...AP1242AG/1242G are not having this problem.
View 2 Replies
View Related
Nov 6, 2012
Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?
View 3 Replies
View Related
Apr 2, 2012
why Windows Server 2008 is not a supported OS for Cisco Network Assistant?I am currently evaluating switch management solutions for use with Catalyst 2960 and 3750 series switches, and would like to be able to backup and restore configurations, as well as make configuration changes. My management Server is running Server 2008.Is Prime LMS my only option?
View 5 Replies
View Related
Jun 23, 2011
I have two WS-C2950G-24-EI switches each of which were running software version 12.1(22)EA2-C2950-I6Q4L2-M. Both swtiches were viewable from Network Assistant version 5.6(3) and part of a community. I then updated the software on one of the switches to 12.1(22)EA14, and now Network Assistant will not add the new updated device to the community and gives an error of "WS-C2950G-24-EI is not supported as community member". Is the latest version (12.1(22)EA14) not supported by Network Assistant? The release notes indicate the Minimum Software Release is 12.1(22)EA4.
View 1 Replies
View Related
Apr 16, 2013
I have an iPad 4 (6.1.3) that won't connect to our Cisco 1142 APs. Full Cisco network; 3560 POE switches on edge and Cisco 6509 at the core.At first we looked at it as a wireless issue. No settings changes on the APs would allow the iPad connect. About 125 other iPads of various models worked fine. Took the offending iPad to McDonalds and it connects fine. Took the offending iPad to another school in our District and it connected and worked fine. Went back to the home school, still won't connect. Contacted Apple since iPad was under warranty, sent it to them and they ran diagnostics and it is fine.Is there anyway that the core switch is blocking the iPad client?
View 1 Replies
View Related
Dec 19, 2011
I have an ASA 5505 configured with internal network, a DMZ, and a VPN on seperate subnets. The implicit rules allow my internal client computers to connect to the web servers on the DMZ IP, but I can not connect to the public NAT address from the internal network. I have a DNS server on my internal network and it does resolve to the public IP correctly. NAT seems to be working correctly because if I go outside the network and connect to the public IP or qualified name then I can get to everything correctly. I do not see any messages in the Cisco logs and the packet trace tool shows the route of http from an internal IP adddress to the external (NATed) address is allowed.
Specifically, I can go to http://192.168.1.121 from the internal (192.168.0/24) network, but I can not go to http://72.22.214.121 (the NAT address) from the internal network. If I am outside my cisco then I can go to http://72.22.214.121 easily. [code]
View 1 Replies
View Related
May 14, 2012
is it possible to prevent the users with static IP's to connect the Network?We use Cisco sw 4500 series as an access and distribution switches.Is there any features on the switches that fit my request?
View 3 Replies
View Related
May 2, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop : [code] I know that the solution would be to download a new valid image from tftp via the common prompt but what i don't undertand is why i cant access the rommon prompt.
View 5 Replies
View Related
May 11, 2012
I'm having trouble in connecting a SG 300 switch with CCA v3.2. I have already connected the switch with CCA, however I can't see anything in my CCA's Front Panel and Topology view. Here is the view of my Front Panel view after I connect the switch ?
View 2 Replies
View Related
Dec 29, 2012
I've been given a F5D7632-4 modem router which is said to be in working order, but without the Setup Assistant Software CD-ROM. How can I get a replacement for this?
View 1 Replies
View Related
May 22, 2013
I have new Belkin router and giving old one to my brother. It is F5D8233-4. Can I install without the CD "setup assistant"?
View 1 Replies
View Related
Mar 22, 2013
im trying to install a dell v715w all in one printer onto my macbook air, wirelessly. In order to do so the installation software says I need to download Dell Wireless Setup Assistant.
View 3 Replies
View Related
Feb 24, 2013
Region : China
Model : TL-WR741ND
Hardware Version : V4
Firmware Version :
ISP :
My router box and the router itself are listed as 741N. I find no reference in the forums or on the website to this model. During setup, I can ping the router from the cmd prompt, but then it fails during the Easy-Setup assistant. I need to use the Easy setup because the language is otherwise Chinese, but it fails the network test. One of the two messages it sends are "Check the Model number". Is this a possibility? Is there a work around or where can I find the proper Setup Assistant software?
View 3 Replies
View Related
Jan 19, 2013
I have a power conncet 6224 with routing enabled with several VLANs setup.VLAN Database: 6,8,10,90-254VLAN 6 is our management vlan10 is for our core network services (DNS, Domain, Exchange etc)90-254 are isolated vlans.What I need to accomplish is to prevent vlans 90-254 from communicating with each other and only allow communication to VLAN 10 and the internet. All internet firewall work will be handled by our Sonicwall. [code]
View 1 Replies
View Related
Jan 11, 2012
we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies
View Related
Mar 23, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 4.23
ISP : GTPL
I recently bought Tp-Link wr740N model but when i run Easy setup assistant on my Windows 8 64bit, A Welcome page appears. When i click START button , a windows error comes out saying. TP-LINK Easy Setup Assistant has stopped working with following error
[code]...
View 3 Replies
View Related
Dec 19, 2011
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
View 9 Replies
View Related
