Does the latest version of the Network Assistant support the AP1131AG / AP1131G model?
From the "supported device list" documentation it seems yes, but I've tried to import them into the map and received the message indicating that is not supported as a device...AP1242AG/1242G are not having this problem.
I have tried to configure EAP-SIM authentication on Cisco Aironet 1131G for Wi-Fi Offload but unfortunately I couldnt make it work. As far as I understand the Wi-Fi standard it is fully supported in 802.11n within WPA2-Enterprise standard. I have read Cisco datasheet for 1131G where your are claiming that you support EAP-SIM in WPA2 also. I have tried to configure it according to configuration guide but it always requires to enter password key first when I try to connect to SSID with configured WPA2 and EAP-SIM. How to properly configure AP or confirm that EAP-SIM needed for seamless 3G/Wi-Fi authentication is supported only within WPA2-Enterprise.
View 4 Replies View RelatedI need to configure 3 Cisco Aironet 1131g for use. Normally we use the Cisco Aeronet 802 and once these are connected onto the switch, I can log on the WLC, find them and change the name and other settings. For some reason I cannot see the Cisco 113g on any of the WLC.
View 2 Replies View Relatedwe have the WLC and 2 x Aironet AP's that is powers over PoE. The other day is was reloaded and since then the AP points are Blinking Red, according the the Aironet manaul this means some sort of boot error? They are also not appearing on the WLC from the GUI or CLI running a show ap summary. Interesting though I can see them via CDP, however they are not picking up IP's as they are listed as 0.0.0.0. After checking with colleagues I was told these were set statically.
Is it possible that the points not having IP addresses is a sign of a corrupt boot environent? I would have though they would not have appeared in CDP if they were corrupt?
I did not set this up in the first place so a little puzzled at the moment? Nothing has changed on the config bar using a different NTP server on the network?
How do I find out the IP address of a aironet 1131ag wireless router?
View 1 Replies View RelatedWe have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
i have managed to create a community of cisco devices however although i can add the pix to the community it does not show up in the topology? HTTPS is enable. I can also access the pix via ASDM.
View 2 Replies View RelatedI'm experiencing considerable difficulties with CNA and my 4948E cat's. Front panel view, vLans and VTP utterly fail...and I have gone to GREAT lengths. I initially configured them all for comprehensive use in a vSphere environment. Storage switch fabric and multi-vlan guest networking. I wiped the config's across the board, factory reset all of them in an attampt to get CNA working. NO GO and it's been wildly frustrating, 80+ hrs spent with no results.
So is CNA truely compatible with the 4948e? And if so, WHAT IN THE **** AM I DOING WRONG!!?!?!?!!!!!?
Config and info:
C4948#show verCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.1(1)SG2, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Wed 24-Oct-12 02:27 by prod_rel_team
ROM: 12.2(44r)SG11C4948 uptime is 22 minutesSystem returned to ROM by reloadSystem image file is "bootflash:cat4500e-entservicesk9-mz.151-1.SG2.bin"Hobgoblin Revision 21, Fortooine Revision 1.40
Last reload reason: Reload command
[Code]...
CNA 5.8(1)
32 devices
When I first launch the application, it promots for CCO login information, but then tells me the username or password is invalid. I reset it once, and it appeared to work. Next time I launched the application though, it gave me the same login error and did not store any of the device credentials. This is a new install of CNA and it just has one community setup on it now. I've tried 2 different CCO accounts and they both give the same login failure. I know the passwords I'm using are correct though.
I'm trying to get a network of SGE2000 switches mapped into Cisco network assistant.It always comes back with the device type unknown and status unsupported device.Is there a way to fix this ? I'm using Cisco network assistant ver.5.7(6)
View 4 Replies View RelatedSince I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
2950s work fine when upgrading the IOS using CNA. On all 2960s I get Failed to execute the command archive download-sw /overwrite /http iosFile
If I run the command using telnet and tftp server it works fine.
I have tried by deleting the old image then trying upgrade using CNA, but no luck
CNA version is 7.5(6)
router: Cisco 2951
error: unable to connect
are able to connect to other switches, such as 2970 questions:
1. is there any configuration needs to be done to connect to 2951 though CNA?
2. is 2951 supported device in CNA?
With my brand new Cisco 3850 Switch, I got it configured with a LAN IP. Then, on my PC I opened up Cisco Network Assistant (version 5.8.5.1 which supports the 3850). I went to add the 3850 to the community by discovering the device, and was prompted with the user/pass box. The password I set was not allowing me to connect, and I realized it's because a username was required and I had not set up a username on the switch. So, I then configured an admin user with level 15 privileges on the switch. However, now when in CNA I try to add the 3850 to the community, it doesn't even prompt me for user/pass, it just says "unable to connect".
What do I need to do to add this 3850 to my community?
I have a Cisco 2948G switch that I am trying to communicate to through this program. It has both an IP address and is hooked up through a cable. I can get Cisco Network Assistant to come up and ask for it's Username and Password, and that it is where I am stuck! I have no clue as to what to put in there as a username and password? I do have a password setup on the switch to login in to it during terminal mode, but that is it.
View 1 Replies View RelatedI have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?
View 3 Replies View RelatedDoes Cisco 1142n Aironet Access Point support WPA-PSK with AES encryption ?
View 1 Replies View RelatedI am trying to connect my Cisco 2911 router to my community in CNA. I can see the routers on the topology map, but when I try to add to community I get an error message stating that the router is unreachable (Unable to connect). I can ping device from ame client. I can view Device Properties for map (Device type: CISCO2911/K9). Telenet attempt to connect but we only use SSH for connectivity (the same as all of my switches that are connected to community). 2911 is listed as a supported router on Cisco site.
View 3 Replies View RelatedDoes Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
We have been successfully using our Aironet 1140 AP in standalone mode with mainly Windows pcs & laptop users, and now, iPads and iPhones. All seem to connect happily through the 1140.
Recently we have a requirent to be able to use Apple's Airplay. Basically, it is not working through the 1140, it works ok via wired ethernet. Can the 1140 support Airplay? - If yes, what precisely must be enabled/configured?
We have a single Class C network without any Vlans. I understand multicast must be enabled, I can't see where to enable this. How to get this working if it is at all possible.
why Windows Server 2008 is not a supported OS for Cisco Network Assistant?I am currently evaluating switch management solutions for use with Catalyst 2960 and 3750 series switches, and would like to be able to backup and restore configurations, as well as make configuration changes. My management Server is running Server 2008.Is Prime LMS my only option?
View 5 Replies View RelatedI have two WS-C2950G-24-EI switches each of which were running software version 12.1(22)EA2-C2950-I6Q4L2-M. Both swtiches were viewable from Network Assistant version 5.6(3) and part of a community. I then updated the software on one of the switches to 12.1(22)EA14, and now Network Assistant will not add the new updated device to the community and gives an error of "WS-C2950G-24-EI is not supported as community member". Is the latest version (12.1(22)EA14) not supported by Network Assistant? The release notes indicate the Minimum Software Release is 12.1(22)EA4.
View 1 Replies View RelatedI find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies View Relatedcan wireless router support up to 100 user including support network printer
View 1 Replies View RelatedI'm having trouble in connecting a SG 300 switch with CCA v3.2. I have already connected the switch with CCA, however I can't see anything in my CCA's Front Panel and Topology view. Here is the view of my Front Panel view after I connect the switch ?
View 2 Replies View RelatedLooking to setup a backup router for our disaster recovery plan. We currently have a Cisco 877W that was setup by our ISP. I can log into the device with Telnet and a console cable, but I am not good using IOS commands, so I would like to use CCA. Unfortunatley, I cannot access the router using the software. I assume something is disabled in the config. Like HTTP or something.
View 1 Replies View RelatedI can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies View RelatedOn autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.
View 3 Replies View RelatedDo the 1131AG APs support band select from a 4400 WLC running version 7?
View 2 Replies View RelatedMy AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.
View 2 Replies View RelatedI am trying to use two different SSID's on my 1131AG each with different security, is this possbile?
View 1 Replies View Related