Cisco :: Does Aironet 1131G Really Support EAP-SIM
Jun 5, 2013
I have tried to configure EAP-SIM authentication on Cisco Aironet 1131G for Wi-Fi Offload but unfortunately I couldnt make it work. As far as I understand the Wi-Fi standard it is fully supported in 802.11n within WPA2-Enterprise standard. I have read Cisco datasheet for 1131G where your are claiming that you support EAP-SIM in WPA2 also. I have tried to configure it according to configuration guide but it always requires to enter password key first when I try to connect to SSID with configured WPA2 and EAP-SIM. How to properly configure AP or confirm that EAP-SIM needed for seamless 3G/Wi-Fi authentication is supported only within WPA2-Enterprise.
View 4 Replies
ADVERTISEMENT
Mar 22, 2011
Does the latest version of the Network Assistant support the AP1131AG / AP1131G model?
From the "supported device list" documentation it seems yes, but I've tried to import them into the map and received the message indicating that is not supported as a device...AP1242AG/1242G are not having this problem.
View 2 Replies
View Related
Dec 11, 2012
I need to configure 3 Cisco Aironet 1131g for use. Normally we use the Cisco Aeronet 802 and once these are connected onto the switch, I can log on the WLC, find them and change the name and other settings. For some reason I cannot see the Cisco 113g on any of the WLC.
View 2 Replies
View Related
Jun 19, 2011
Does Cisco 1142n Aironet Access Point support WPA-PSK with AES encryption ?
View 1 Replies
View Related
Mar 20, 2013
Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
View 3 Replies
View Related
Oct 12, 2012
We have been successfully using our Aironet 1140 AP in standalone mode with mainly Windows pcs & laptop users, and now, iPads and iPhones. All seem to connect happily through the 1140.
Recently we have a requirent to be able to use Apple's Airplay. Basically, it is not working through the 1140, it works ok via wired ethernet. Can the 1140 support Airplay? - If yes, what precisely must be enabled/configured?
We have a single Class C network without any Vlans. I understand multicast must be enabled, I can't see where to enable this. How to get this working if it is at all possible.
View 3 Replies
View Related
May 27, 2012
I find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies
View Related
Feb 16, 2011
can wireless router support up to 100 user including support network printer
View 1 Replies
View Related
Mar 7, 2013
Okay, I'm working on a project and the company I work for wants to add 5 Ghz antenna's to their Aironet 1252's. Okay not a problem, except I've never worked with these routers before and I can't get the configuration set (). Once I get 'em on one I can get them all done.
View 14 Replies
View Related
Mar 7, 2013
I'm trying to configure my Cisco Aironet 1252's in my office to utilize their 5GHz antenna's but I've never worked with these routers before .
View 9 Replies
View Related
Jan 5, 2013
We are planning to implement Aironet 3500, Do we need to have controller to install it or can we install as standlone AP.
View 1 Replies
View Related
Jul 24, 2011
at one of my Aironet 1200 the update through web interface of the IOS seems failing. THe webpage now looks damaged and not all points are availible.
I now want to update the IOS through telenet. A TFTP server is running and it is sharing the actual TAR-file.
View 7 Replies
View Related
Oct 8, 2012
We have Cisco Aironet 1240AG Wireless AP's in out network. Now, we have some PC's, laptops and mobile phones connected with with this AP and all devices are working fine. Now suddenly from today when I am trying to associate some new devices to the AP it is not working means the devices are not associating.
View 2 Replies
View Related
Dec 5, 2012
I just configured Aironet 3502i and it works ok but no lights. I could see the AP in switch, in WLC, and in WCS and ping ok but when you see it mounted it has no light. I tried to shutdown the port in the switch and I saw it turns green (booting), once it was registered in WLC the light will be off.
View 12 Replies
View Related
Jul 25, 2012
how I can configure the Aironet 3600e by Cisco without a WAN Controller. I know it's a controller based AP but I bought it in preparation for my new WiFi Network Design as I'm planning to deploy these APs together with a controller but at this stage all I need is just basic config so that I can see how good it will work in the environment I want to implement it. So I was wondering if there is some kind of default IP and Admin/ Password as I could not find the info on Cisco's website.
View 4 Replies
View Related
Jan 8, 2013
everyone can connect to the 1040 ap except my laptop and another one. for some reason it stopped showing , it was working fine and out of the blue nothing.
View 2 Replies
View Related
Jan 23, 2013
I was wondering if its possible to setup the Cisco Aironet 1260 as a WDS master with radius and another Cisco Aironet 1260 as a slave for seamless roaming. How many slaves can a WDS master handle?
View 1 Replies
View Related
Aug 7, 2012
I just bought an Aironet 600 OfficeExtend AP and hooked it up to my WLC 5500 but I can't configure it.
I've got 10 AP running just fine but the Aironet 600 shows operational status as "UP" (normal is "REG") and "Admin status", "AP Mode" and "AP Sub Mode" are all grayed out.
I installed the newest firmware on the WLC (ver 7.2.110.0) and it has upgraded the Aironet 600 as well.
I've read to through the installation manuals and from everything I can see I should be able to configure the Aironet 600 as soon as it contact WLC
View 3 Replies
View Related
Dec 5, 2012
I have two cisco airenet 1252 autonamous access point that are configured as point to point bridge. Now I want to confiure AES encryption or WPA2 using a pre-shared key however I do not see the option to do this . The only option I see under ciphers are:
wep 128
wep 40
TKIP
[Code].....
Is it possible to use either AES or WPA2 using a pre-shared key on the 1252 autonamous access point? preferably using the web interface.
View 3 Replies
View Related
Aug 2, 2011
I've set up a Cisco Aironet 1301 AP to be used for a guest network. I've got several other of the Aironet 1140-series around the business but none of them are in reach of this one at the moment.
The problem I have is that clients that try to connect to the AP are either not able to connect at all or lose their connection after some seconds. The config is more or less copied from the other APs with the same guest VLAN.
View 2 Replies
View Related
Sep 4, 2012
I've recently obtained a Cisco Aironet 1242AG WAP. I do realize this is not a standalone router. I would like to use it as an extension of my current router. So right now, the status light is alternating colors. If I understand this correctly, it cannot find the controller. I cannot telnet into it, or use the web broswer interface. They both say the connection is not available. However, when I check my DHCP table from my router, I see that an IP has been assigned to the MAC for the WAP. I've tried doing a factory reset by holding MODE before I plug in the power, and waiting until it turns amber. After a few minutes and going through a few LED changes, it goes back to continuosly alternating colors.
View 14 Replies
View Related
Mar 8, 2011
In a multiple SSID setup, can Aironet 1240 & 1250 series AP supports different WEP key for different SSID
View 3 Replies
View Related
Oct 21, 2011
I am trying to configure an Aironet 1142 WAP model#AIR-AP1142n-A-K9. My setup is very basic, I have a router that acts as the DHCP server, the 1142n, and a PC. I am using the 1142n in Standalone AP mode no authentication, and have it working according to the [URL]. And it is working perfectly. My questions are as follows.
1. I have isolated the wireless users from seeing each other by using ap isolation, Can I prevent the wireless users from accessing the lan pc, router and WAP configuration pages? Is there any way to do that while still maintaining internet access? Basically I just want to provide my users wireless internet access without authentication but don't want them able to see each other or anything on the lan.
View 2 Replies
View Related
Jun 4, 2012
I was wondering is there any way to make my Cisco/ AIRONET-350 Series- Wireless Lan Adapter reception stronger or an upgrade available
View 3 Replies
View Related
Aug 17, 2011
I need information about the Aironet 600 access point.I got a customer who want to deploy a guest WLAN on branch office with an authentication with a captive portal that is centralized. I would like to use the OfficeExtend functionnality with Aironet 600 Acces point & WLC 5508 or 2504 to centralize the traffic from all access points on the controller.
On those branch offices, there were a few "free access desktops" that need a copper link. I want those devices to be also authenticated by captive portal, so I want to connect them on the four 10/100 port of the access point. But it seems that we can only use one port as "corporate remote LAN", the threee others are just for "home LAN". Is it correct ? Is there any solution to configure the four ports as remote LAN interface ?
View 3 Replies
View Related
Feb 2, 2012
Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
Also if so, can you use 11n channel bonding on the bridge link?
I need to link 2 buildings together wirelessly approximately 70 metres apart. There is direct line of sight between them.
View 10 Replies
View Related
Oct 23, 2012
I think it was either the late 90's or early 2000's, I received 2 ap340 devices, didn't know what they were and what to do with them. I was in a program for beta testing through a company that would send items from various businesses, think that is where they came from. Anyway, fast forward to 2012, I want to use them for what they are. I would like to upgrade them to a firmware version that has better wireless security. What are my options with these 2 AP's, besides using them as paper weights? Also I have a USB to serial cable and try to connect to AP's using telnet, I thinik I bricked one! Don't really know what to do, other then spending many hours trying to do a factory reset, only to waste many hours trying to getting it connected.
View 0 Replies
View Related
Dec 5, 2012
I have two Cisco Aironet 1252 that I want to configure as a point-2-point bridge. Now I want to know if this configuration supports the 802.11n protocol.
View 2 Replies
View Related
Sep 20, 2012
Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies
View Related
Jun 30, 2008
I deleted the ios image form the aironet device from command line when i was trying to updgrade it.Now the aironet 1100 keeps rebooting.I've tried to hold down the mode for 30 seconds goes red, but keeps rebooting.
View 2 Replies
View Related
Jan 27, 2013
I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies
View Related
Jul 21, 2011
I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies
View Related
Aug 20, 2012
I have found that there are only few configuration to the Cisco Aironet 600 OEAP. The settings are just for basic configuration for a wireless network when it is in autonomous mode.
A need for a Wireless LAN Controller to perform advance settings.
Also, there are no firmware available in Cisco. No upgrade/downgrade firmware avalaible for download.
View 4 Replies
View Related
