at one of my Aironet 1200 the update through web interface of the IOS seems failing. THe webpage now looks damaged and not all points are availible.
I now want to update the IOS through telenet. A TFTP server is running and it is sharing the actual TAR-file.
how i can limit the bandwidth for a all my client conect to the AP, i have a Aironet 1200 with the 12.2.15 code.
View 3 Replies View RelatedIs there a way to configure client/user to AP authentication without using encryption for joining to an wireless network? What we need to do here is protect network access at our hotspots by enforcing a password to get connected. The other part is making it compatible with every possible device so we need to have encryption off. We have a mixed environment at this time until everything is upgraded. Aironet 1200 series and some new Aironet 1142 models. No controller, all standand alone AP's
View 2 Replies View RelatedI would like to be able to have a few "guest" users on the Wireless network for visitors. Is there any method to have a prompt for "Username / password"? I would like the user accounts to have different expiry periods if this is possible. My current config is attached. The SSID "test" appears on the network. The SSID "test111" does not appear.
View 1 Replies View RelatedWe had two dozen Aironet 1200 access points and a controller donated to us from a local hospital that no longer needed them. My boss would like me to set one up with 3 VLANs:
- encrypted VLAN for staff
- encrypted VLAN for students
- unencrypted VLAN for guests
Ultimately, we'd like the staff VLAN to have access to all internal network resources, the student VLAN to have access to several pre-defined printers, and the guest VLAN is web-only access. Whether the controller we were given will accommodate that, we won't know until we get one Aironet 1200 programmed and connected to the controller. For the time being, I just want to get this access point programmed with the 3 VLANs.
I'm easily able to get it running a single SSID (non-VLAN) network and confirm that I can use that network fine. However, I need to set up these 3 VLANs. I can connect to it via telnet if that'll let me program it faster.
I have some aironet 1200 AP's. I want to use this with a windows 2008 radius server. I followed the guide on [URL]. Unfortunately I can not get this working. In the securtiy log of the event viewer there is always the message "authenication was not succesful because an unknown username or incorrect password".
- Is it possible to get this working?
- If yes, is there a manual how to configure the AP's and the radius server, or are there any hints?
- Is this the best way to setup a wireless network or is there a better way?
I saw there is also a local radius server inside the 1200. Can all the 1200's work together? I suppose that if I use the built-in radius server than I can't make a connection to my AD database, correct?
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedI'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.
View 3 Replies View RelatedI have a Cisco Aironet 1200 series Access point and currently i am using wep with 128 bit . My concern is that i want to change this key with current SSID .
My current SSID is ABtc. My current key is abcdefgh12345. when i try to change the key its give me error :
"encryption key must be 26 hexadecimal characters" .
we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View RelatedI have a Cisco Aironet 1200 Series Access Point. It takes long time to boot up.
After showing the warning banner message it takes long time before asking for username.
The sh version is given below.
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA4, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Tue 05-Sep-06 14:15
[Code].....
I have a Cisco 1200 Series (AIR-AP1231G-A-K9) access point, I have been upgrading these models to lightweight mode but are having issues with one in particular, this access point keeps "rebooting" itself, I am assuming that the upgrade failed, how can I get the access point upgraded?
When I start to access the AP by typing "enable" and enter the password it starts resetting again.
I have reset the AP by the mode button, power option but still not working.
At this point I would even accept a fix to get it back to working condition. Here is a capture.
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
I was wondering is there any way to make my Cisco/ AIRONET-350 Series- Wireless Lan Adapter reception stronger or an upgrade available
View 3 Replies View RelatedOnce I got LAP1142N from ebay and converted from Lightweight to Autonomous via TFTP but I see there is new IOS came out so it required to upgrade Bootloader which is c1140-boot-m.124-23c.JA1.bin and IOS is c1140-k9w7-tar.152-2.JB.Currently 1142N running IOS c1140-k9w7-tar.124-25d.JA and Bootloader Version 12.4(18a)JA.For while few hours ago I kept figuring it out how to upgrade bootloader on website but none of these will work.
View 8 Replies View RelatedHow to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies View RelatedI'm attempting to update the software on three aironet 1100 from System Software Filename:c1100-k9w7-tar.122-13.JA2 System Software Version:12.2(13)JA2 Bootloader Version:12.2(8)JA To the latest release or the 12.3x family and it fails."the software upgrade was interrupted and was not able to be completed" I also disabled the Radio braodcast?
View 1 Replies View RelatedWe have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.
I run into a 1230 that would have a Web page completely different than the usual one. Instead of getting the normal User/pass menu and then the menu on the left side frame, you get this:
Cisco Systems
Accessing Cisco AIR-AP1220-IOS-UPGRD "1200AP"
Web Console - Manage the ap through the web interface.
Telnet - to the router.
Show interfaces - display the status of the interfaces.
Show diagnostic log - display the diagnostic log.
Monitor the router - HTML access to the command line interface at level 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
Extended Ping - Send extended ping commands.
Show tech-support - display information commonly needed by tech support.
Everything appears to work ok in that peage excepting the "Web Console" link which would probably go to the usual home page.Getting to it from the console, everything looks to be ok. You can configure the unit using the IOS and the unit apparently works fine. I have 12.2(13) JA3 running.I defaulted the unit, reloaded the image... I'm still getting that home page.
We have a 1200 Aironet just go down hard for no reason through out the day, we replaced the Power Injector with a C2960 POE Switch, we also replaced the cabiling. When it goes down hard all three lights are still green as if the AP is still up. We verified the IOS with other stores and everything is the same on the configurations, versions, and IOS.
View 35 Replies View RelatedI have been looking for a new router that can handle intensive bandwidth for my office which can handle vlans, QoS, bandwidth management, VPN/VPN Passthrough, and perhaps multi-WAN/Load Balance. A friend has recommended the Mikrotik RB 1200 for my application, having looked at the product the feature set seems to be quite extensive and the price point is very attractive. The router is also rack mountable (a big plus!!!), my question is wether the router is relatively easy to configure/manage. I have managed/installed other routers such as the Cisco SMB series but I have no experience with Mikrotik. I am very tech savvy and have a moderate knowledge of network infrastructure. I have heard so may different responses to the simplicity and I would like y'all to weigh in before I purchase the router. (OR WHATEVER RACKMOUNTABLE ROUTERS YOU RECOMMEND FOR SMB)
View 10 Replies View RelatedI got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
I have two wireless networks configured in the AP1200, both SSIDs are configured with WPA.
SSID 01: configured whit WPA
SSID 02: configured whit WPA
I have configured the access-list number 700, and I would like to apply to a single network. Achieving the following:
SSID 01 : WPA + Mac Filter, using the ACL number 700.
SSID 02: WPA
How I can apply the list 700 to the first SSID only ??
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
View 6 Replies View Relatedsetting up two VLANs for my WAP: one for all local network and internet traffic and one for just (guest) internet traffic. I just purchased both devices but I don't know if I have the option for free Cisco phone support.
View 1 Replies View RelatedI want to disable the MAC authentication that is configured in my Aironet 1200 Cisco Access Point, now set to "Local list only". I want that any wireless device can connect if the user knows the wep password.
I cannot find the option to disable the MAC authentication.
I am using 5 Cisco 1200 Series APs with both an A and G radio. Is there a benefit/problem to running both simultaneously? I would have one SSID and is setup for Fast Roaming as well.
View 1 Replies View RelatedFor the past week, I've been looking to implement wireless technology at our educational site. We've conducted some tests with an AP1200 and we were satisfied with the performances of 802.11a standards.
Since one of our requirements is bandwidth, we are looking to implement a 802.11g standard for that need. Unfortunately, Cisco does not offer any client access adapter for that 11g standard as opposed of the competition. What kind of client adapter (PCMCIA) can Cisco recommend to work with AP1200 under the 802.11g ?
I have 2 Cisco 1200 G AP's connecting 2 different locations. Location A ( La ) I have a RVO82 router connected to a 50Mbit cable connection. I have an AP setup there using a 1 Watt booster and a 24db wire grid directional antenna. Only one antenna here, the other disabled.
At Location B (Lb ), about 1.5 miles away, with good to excellent line of site, i have the other setup as a WGB with a 15db wire grid directional antenna with a 1 Watt booster. Also only one antenna here, the other disabled.
WGB feeds a simple 8 port switch and in that switch i have a simple belkin wireless router setup as an AP for Lb's wireless access,
The signal strenght between the two locations is -49 to -52 db, depending on what time of day I check it.
I have had this setup for a couple of years now. I recently switched from a 3Mbit DSL connection to the 50Mbit cable connection hoping to increase my bandwidth with no luck.
.
When I first set this up i had a 6Mbit cable connection and it maxxed out at 5 Mbit at Lb. I thought i would be able to add more boosters and antennas as time went on to go from half duplex to full duplex (the way i think of it is one antenna receiving and the other sending, at both locations) so that when our ISP had faster rates available, i could upgrade. I recently read somewhere on the net that it is not possible to run full duplex in the AP to WGB setup i have. Is that true?
My main concern is increasing bandwidth on the WGB side Lb. When i upgraded to 50Mbit, i still only max out at 5mbit at Lb. Before i thought it was due to not being full duplex or weaker signal strengths (I've always had the 1watt booster at Lb, then i added one later to La with no benefit noticed except signal strength is better and uploads seem faster from Lb....)
I have two different LAP 1300 and 1200 in my network and I need to add theme to the WLC,I successes to add one of theme by the option 60 in the DHCP pool at the Core SW,How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
View 4 Replies View RelatedIs there any detailed documentation on the Site Survey Client mode on the AP 1200?When using this mode I cannot see any indication that it has associated withthe root AP. I would like to be able to pass traffic from the ethernet port to the root AP VIA the AP in client mode. The Ap in client mode shows the radio in blocking when in client mode, is this normal? Is there a way to manually change this to forwarding mode?
View 4 Replies View Related I've got an iPad2, which works without issue at home (1130 AP/ASA5505), but at my office, we have a 1200 series AP. It's hit and miss, but other people who bring iPads in have noticed the same issue--our internal SSID is non-broadcast. Even though the SSID is previously configured and works on occassion, there are times where it won't even see the SSID at all to connect.
This happens with iPad and iPad2, iOS4 and iOS5...
LIke i said, works fine on my non-broadcast SSID at my home on an 1130 AP...
I have a WLAN with 5 1200 Series AP (A/G) configured for Fast Roaming using the Cisco supplied documentation. Can I use one user name for all of my devices to connect to the Internal Radius Server? This would be similar to having a passphrase for WPA.
View 3 Replies View Related