I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.
I have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.
View 3 Replies View RelatedI'm attempting to update the software on three aironet 1100 from System Software Filename:c1100-k9w7-tar.122-13.JA2 System Software Version:12.2(13)JA2 Bootloader Version:12.2(8)JA To the latest release or the 12.3x family and it fails."the software upgrade was interrupted and was not able to be completed" I also disabled the Radio braodcast?
View 1 Replies View Relatedhow to connect macbook air with cisco 1100 series access point
View 2 Replies View RelatedI have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?
View 8 Replies View RelatedI have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
I have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.
View 5 Replies View RelatedI recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
I am recently engaged by a client to convert his network to wireless network. My client operates in an office with 8 floors and also concrete walls. On making my research i came about your product Cisco AP500 Series Wireless Access Points.I will like to know if this product can work for my client perfectly or I will need to get other enhancement to make it work at its optimum.
View 2 Replies View RelatedI have a customer who bought Cisco Aironet 3500 Series. Currently 4404 WISM Controllers are installed with 1142 Access-Points. The WLC-Version is 6.0.199.
Will the 3500 Series Access-Points work? (Of course without the spectrum intelligence feature)?
The Q&A says the following: Are there any concerns with supporting the new Cisco Aironet 3500 Series Access Points with the older Cisco 2000, 2100, 4100, or 4400 Series Wireless LAN Controllers?
I deleted the ios image form the aironet device from command line when i was trying to updgrade it.Now the aironet 1100 keeps rebooting.I've tried to hold down the mode for 30 seconds goes red, but keeps rebooting.
View 2 Replies View RelatedI have to configure DHCP on Aironet 1100 WAP so wireless client will get IP address through WAP. I tried all the option mentioned in Document but nothing is working.
View 1 Replies View RelatedI'm doing a project on trilateration in which is required to list the BSSID and power levels from the APs, since we have alot of Cisco Aironet 1100 deploye here, could this be a choice ?
My first try is to get these values using snmp, but so far had no luck finding the right MIB. I don't think the console might be useful, will it ?
I know I'm assuming alot, that the Aironet enables for a 'iwlist' dump, and that these values can be retrieved through snmp. But seems something reasonable for them to have, even if I haven't found it.
We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies View RelatedIf the 2600 series access points are compatible with a 4404 controller running 7.0.235.3 code? I was looking for a compatibilty matrix for the AP to controller to code comparison but couldn't find one.
View 1 Replies View RelatedDoes Cisco SG300-28P provide enough PoE to power access points 1550 and 1600?
View 1 Replies View RelatedI find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies View RelatedI have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck.
I also have a Cisco Aironet AP1242AG that is doing the same thing.
We have 5 Cisco Aironet 1100 wireless access points and we are having huge problems in the last few days with them disconnecting some mobile barcode scanners that we have.
We have two Aironet's in the top of the factory which work fine and 3 down the bottom which keep kicking the barcode scanners off. If we use the barcode scanners at the top of the factory they work fine, as soon as we come down to the other 3 WAPs it they keep connecting and disconnecting.
We get the following error in the Event log on the access points.Disassociated because sending station is leaving (or has left) BSS On the barcode scanners. [code]
I have an 1100 series AP and it seems to be configured properly, but every few minutes or so the connection will drop and then come back up again. It is happening on two different laptops. Both using Windows XP. 1 is using a Dell True Mobile wireless card and the other is using a Cisco 350 series wireless card. I am using 128 bit encryption and the signal strength says excellent on both laptops.
View 2 Replies View RelatedI am trying to connect macbook air with cisco 1100 access point,but it is not connecting.
View 1 Replies View Relatedin my company we have 40 cisco aironet 1100 without controller, the signal is good with laptops but is too weak with the iphone's ipads and blackberry.
View 12 Replies View Relatedwe have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View RelatedWe are re-designing our wireless network and are navigating the security options.Are design will include a 5508 WLC and 3600 series APs. We plan on breaking our wireless out into four VLANS.Is 802.1x the standard for wireless authentication?What EAP flavor would you recommend for wireless? We will be supporting an environment with a variety of mobile devices (iPhone, iPad, HP tablets, Dell laptops, etc.). We will also be supporting wireless Cisco VoIP phones. Someone suggested choosing between EAP-Fast or EAP-PEAP, does this seem reasonable? Also, if we want to authenticate users using their AD account, we need to have NPS running on the AD server and use the radius protocol from client to server, is that right?
View 1 Replies View RelatedCan Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedIs there a way to start with a LAN MAC address for a Cisco 1100 Series AP and look up the corresponding wireless MAC address and vice-versa? What I am looking for is either a cross-reference table or a lookup program where one of the MAC addresses would be entered and the other would then be displayed. The two MAC addresses for the 1100 series AP's are completely unique, they are not simply one digit apart.
View 2 Replies View Relatedlinks with information / guidelines for the initial setup for this Access Point?
View 7 Replies View Relatedhow to setup the Aironet 1602 (AIR-SAP1602I-E-K9) I have tried accessing it by various IPs like 10.0.0.1 or 192.168.1.254 but none of them work also when I monitor the connection using Wireshark I can't find out what its IP is.
View 4 Replies View Relatedaccess point and the limitation on the users connected to the SSID using a wireless lan controller. From the installation guide I see an incredible thing:
Supported User Count Only fifteen users are allowed to connect on the WLAN Controller WLANs provided on the 600 series at any one time. A sixteenth user cannot authenticate until one of the first clients de-authenticates or a timeout occurred on the controller. Note: This number is cumulative across the controller WLANs on the 600 series. For example, if two controller WLANs are configured and there are fifteen users on one of the WLANs, no users will be able to join the other WLAN on the 600 series at that time. This limit does not apply to the local private WLANs that the end user configures on the 600 series designed for personal use and clients connected on these private WLANs or on the wired ports do not affect these limits.
Is it possible a terrible limitation like this ?
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedI'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies View RelatedI purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies View Related