I'm attempting to update the software on three aironet 1100 from System Software Filename:c1100-k9w7-tar.122-13.JA2 System Software Version:12.2(13)JA2 Bootloader Version:12.2(8)JA To the latest release or the 12.3x family and it fails."the software upgrade was interrupted and was not able to be completed" I also disabled the Radio braodcast?
View 1 Replies
I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.
I deleted the ios image form the aironet device from command line when i was trying to updgrade it.Now the aironet 1100 keeps rebooting.I've tried to hold down the mode for 30 seconds goes red, but keeps rebooting.
View 2 Replies View RelatedI have to configure DHCP on Aironet 1100 WAP so wireless client will get IP address through WAP. I tried all the option mentioned in Document but nothing is working.
View 1 Replies View RelatedI have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.
View 3 Replies View RelatedI'm doing a project on trilateration in which is required to list the BSSID and power levels from the APs, since we have alot of Cisco Aironet 1100 deploye here, could this be a choice ?
My first try is to get these values using snmp, but so far had no luck finding the right MIB. I don't think the console might be useful, will it ?
I know I'm assuming alot, that the Aironet enables for a 'iwlist' dump, and that these values can be retrieved through snmp. But seems something reasonable for them to have, even if I haven't found it.
I find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies View RelatedI have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck.
I also have a Cisco Aironet AP1242AG that is doing the same thing.
We have 5 Cisco Aironet 1100 wireless access points and we are having huge problems in the last few days with them disconnecting some mobile barcode scanners that we have.
We have two Aironet's in the top of the factory which work fine and 3 down the bottom which keep kicking the barcode scanners off. If we use the barcode scanners at the top of the factory they work fine, as soon as we come down to the other 3 WAPs it they keep connecting and disconnecting.
We get the following error in the Event log on the access points.Disassociated because sending station is leaving (or has left) BSS On the barcode scanners. [code]
in my company we have 40 cisco aironet 1100 without controller, the signal is good with laptops but is too weak with the iphone's ipads and blackberry.
View 12 Replies View RelatedI have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?
View 8 Replies View RelatedWe have a Cisco aironet 1162N connected to a Wireless Controller (LIGHTWEIGHT mode), the device failed and it needs to be replaced.We have a Cisco aironet 1142N in stock available to use.Can we proceed with the change just with disconnect the failed AP (model: 1162N ) and connect the new one (model: 1142N)? Or there is any other task to be done before the change? since the WLC manages the configuration for each AP.
View 8 Replies View RelatedHaving problems losing connectivity so decided to upgrade firmware from v1.00.7 to latest version available.
Downloaded the upgrade file and log into web based administrator. Select file and click on UPGRADE button. A couple of clicks on timeline then: UGRADE FAILED
I am trying to upgrade the firmware on my Linksys v1 router from 1.0.02 to 1.0.03 over a remote 56Kb circuit. I appear to be having a timeout problem. The upgrade always fails. I have upgraded several E1200s in my office over ethernet, and the upgrade appears to finish when the progress bar is at 15%. However, on my remote upgrade, the progress bar gets to 98%, hangs for a few more seconds, and then pops up a window with "Upgrade failed".
I suspect that there is a timeout on the upgrade process, and that I can't upload the 3.8 MB firmware file fast enough. If so, is there any way to increase the upgrade timeout?
I have tried repeatedly to upgrade my firmware from 1.0.03 to 1.0.04, but it always fails with a message :cannot upgrade at this time..." I've tried both IE and FireFox, and both wired and wireless connection to my PC (Windows 7).
View 4 Replies View RelatedI'm trying to upgrade my frmware to the lastest one (classic firmware) I've downloaded this file multiple times [URL] When I try the firmware upgrade (manual upgrade) and select the file, it always complains about the file being corrupt (using the .ssa file in the zip).
View 6 Replies View RelatedOnce I got LAP1142N from ebay and converted from Lightweight to Autonomous via TFTP but I see there is new IOS came out so it required to upgrade Bootloader which is c1140-boot-m.124-23c.JA1.bin and IOS is c1140-k9w7-tar.152-2.JB.Currently 1142N running IOS c1140-k9w7-tar.124-25d.JA and Bootloader Version 12.4(18a)JA.For while few hours ago I kept figuring it out how to upgrade bootloader on website but none of these will work.
View 8 Replies View RelatedHow to upgrade C3502i to Lightweight? I failed to upgrade using Upgrade tool v3.4. The error message is "AP model is not supported" . how can I upgrade it?
View 9 Replies View RelatedIf by mistake I have attempted to upgrade the firmware my router "WRT610N" via my wireless laptop and after 24 hours the same screen "upgrading router" continues displayed and the router does not respond, How do I fix this?
View 9 Replies View RelatedWe have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
I try upgrade ACS 5.3.0.40 to new version 5.4.0.46. Everything looks ok:
ACS-machine/acsadmin# application upgrade ACS_5.4.0.46.tar.gz rep01 Do you want to save the current configuration ? (yes/no) [yes] ? Generating configuration. Saved the running configuration to startup successfully
% CARS Install application required post install reboot...
Broadcast message from root (pts/0) (Thu Dec 6 23:36:41 2012):
The system is going down for reboot NOW!
Application upgrade successful
But ACS machine (vmware instance) can't boot with this result: Volume group "smosvg" not found. (for details see attachment)
I am trying to upgrade ISE from 1.1.0 to 1.1.2.145 but failed. Find the details below.
DR-ise-pdp-01/admin# application upgrade ise-appbundle-1.1.2.145.i386.tar.gz ISE1
Save the current ADE-OS running configuration? (yes/no) [yes] ?
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
Stopping ISE application before upgrade...
Running ISE Database upgrade...
% Application upgrade failed. check logs for more details.
I upgraded an ASA 5505 from 8.3(2) to 8.4(4) this evening. The 5505 is a backup and used to perform testing prior to production changes. After the upgrade was complete, a VPN tunnel began to fail. I did a limited search online to see if this was a known issue or something new. I also reviewed the release notes but did not see anything that matched the issue I received.
My concern is that this tunnel configuration is scheduled to be deployed to the production firewalls next week after their upgrade. But if it failed on the upgraded test unit, it may fail on the production units.
I downgraded the backup unit to 8.3(1) and verified that the tunnel indeed worked at that level.
I have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View Relatedat one of my Aironet 1200 the update through web interface of the IOS seems failing. THe webpage now looks damaged and not all points are availible.
I now want to update the IOS through telenet. A TFTP server is running and it is sharing the actual TAR-file.
After upgrading from a 1231 autonomous to an 1142 autonomous AP some machines can no longer authenticate. AP logs show authentication failure and access reject coming from the Radius server. Radius server shows authentication failures but no specific reason. Using the same account on another machine works fine. Machine settings have been verified and if we go back to the 1231 all users authenticate fine. Below are the configs:
OLD AP:
!
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
[code]...
I was wondering is there any way to make my Cisco/ AIRONET-350 Series- Wireless Lan Adapter reception stronger or an upgrade available
View 3 Replies View RelatedI have a stack of 4 Cisco Switch 3750 (1 x WS-C3750G-24T, 2 x WS-C3750-48P and 1 x WS-C3750V2-48PS) and I want to do an firmware upgrade of this stack. Actually, all the 4 switches are at the firmware version 12.2(50) SE1 "IPBase" and I want to upgrade them to 12.2(55)SE5 IPBase. According to the release notes, all the switches in my stack are supported.
To upgrade the firmware, I use the command "archive download-sw /imageonly /overwrite tftp://IP_Address/c3750-ipbaselmk9-tar.122-55.SE5.tar" The firmware gets uploaded correctly but then I get the error message "There is insufficient space in flash: to install the required image. Clean up some old images, and try again."
When I do a "show flash", I see that the switch has 5650944 bytes free of 15998976 bytes.
How can i upgrade my switches? Is there an error in my command which I use? Do I need to add an other option?
The problem is, the switches are located in a branch office and there is no direct access to them. Everything must be done remotely.
I'm trying to "resurect" an old wireless network made with Cisco Aironet 1100. One of the AP has lost its IOS (due to an error while trying to upgrade it through the web interface)
I tried to reload it with the "mode button". I can see in my TFTP server logs that the AP is downloading the IOS but nothing happens and the AP keep being stuck (leds are : red/green/red)
I have an 1100 series AP and it seems to be configured properly, but every few minutes or so the connection will drop and then come back up again. It is happening on two different laptops. Both using Windows XP. 1 is using a Dell True Mobile wireless card and the other is using a Cisco 350 series wireless card. I am using 128 bit encryption and the signal strength says excellent on both laptops.
View 2 Replies View RelatedIs there any possibility to limit the bandwidth per SSID on Cisco Aironet 1100 that is connected to Cisco router 876? So the main goal is to have two SSID one for the guests and one for the colleagues and to limit for example half the bandwidth of internet link per SSID so we dont get into situation that colleagues overload whole internet link so that guests can always surf without problem.
View 3 Replies View RelatedI am trying to connect macbook air with cisco 1100 access point,but it is not connecting.
View 1 Replies View RelatedI have a dell inspiron 1100 laptop that i have a dell truemobile 1300 802.1.1 b/g PC card in for my wireless connection. My router is Libebox-7bd8 i thinkI have tried to connect to the internet as usual but keep getting "page cannot be displayed" but the pc says that i am connected to my live box with excellent connection.I also have a pc that has a wired connection that works perfect?I called my net provider one man said that oh no its your wireless card and hung up and another lady actually took my details and told me it was a common fault and it will be fixed withing 3 hours that was a week ago !
View 14 Replies View Related
