in my company we have 40 cisco aironet 1100 without controller, the signal is good with laptops but is too weak with the iphone's ipads and blackberry.
View 12 Replies
I deleted the ios image form the aironet device from command line when i was trying to updgrade it.Now the aironet 1100 keeps rebooting.I've tried to hold down the mode for 30 seconds goes red, but keeps rebooting.
View 2 Replies View RelatedI have to configure DHCP on Aironet 1100 WAP so wireless client will get IP address through WAP. I tried all the option mentioned in Document but nothing is working.
View 1 Replies View RelatedI have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.
View 3 Replies View RelatedI'm doing a project on trilateration in which is required to list the BSSID and power levels from the APs, since we have alot of Cisco Aironet 1100 deploye here, could this be a choice ?
My first try is to get these values using snmp, but so far had no luck finding the right MIB. I don't think the console might be useful, will it ?
I know I'm assuming alot, that the Aironet enables for a 'iwlist' dump, and that these values can be retrieved through snmp. But seems something reasonable for them to have, even if I haven't found it.
I'm attempting to update the software on three aironet 1100 from System Software Filename:c1100-k9w7-tar.122-13.JA2 System Software Version:12.2(13)JA2 Bootloader Version:12.2(8)JA To the latest release or the 12.3x family and it fails."the software upgrade was interrupted and was not able to be completed" I also disabled the Radio braodcast?
View 1 Replies View RelatedI find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies View RelatedI have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck.
I also have a Cisco Aironet AP1242AG that is doing the same thing.
We have 5 Cisco Aironet 1100 wireless access points and we are having huge problems in the last few days with them disconnecting some mobile barcode scanners that we have.
We have two Aironet's in the top of the factory which work fine and 3 down the bottom which keep kicking the barcode scanners off. If we use the barcode scanners at the top of the factory they work fine, as soon as we come down to the other 3 WAPs it they keep connecting and disconnecting.
We get the following error in the Event log on the access points.Disassociated because sending station is leaving (or has left) BSS On the barcode scanners. [code]
I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.
I have an issue when I´m trying to authenticate my iphone&blackberry device with ASA 5520 using certificates. It seems that certificates are working fine, pass the ike phase 1 but never complete the phase 2. When i use pres hared keys everything works fine with both devices.
If you consider necessary, i can provide my current configuration in asa.
I currently have a WAP4410N connected to an ethernet switch and the signal is very weak when attempting to connect to the AP from 4 rooms away. The structure is all block and the signal does not do well between the solid walls. I would like to roam from room to room on the same SSID. how to have the second WAP4410N repeat the original signal and reaplify it from the first WAP to solve this issue. Also, I cannot connect the second WAP to the ethernet switch it must be wireless.
View 1 Replies View RelatedI have a Verizon router with biltin wireless. I want to use my Apple Extreme for my home network
View 1 Replies View RelatedI've typed this question 4 times and keep losing signal so sorry if it appears multiple times, i have moved rooms and my laptop, toshiba satellite is now getting very weak signal. i bought a netgear usb adapter but it doesnt solve the problem much.
View 9 Replies View RelatedI have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?
View 8 Replies View RelatedA while ago I replaced my wireless card, and the new one get's considerably weaker signal strength and drops out periodically. I'm sure the problem is with the card itself (or its firmware). It not only get's weak signal strength from my router, but every surrounding network, and sometimes can't detect any networks for a few minutes. I've used several other wi-fi devices in the same spot where this system is sitting and they all get excellent signal strength.I've already tried changing channels on my router and re-installing drivers. Neither has any effect.The card in question is a TP-Link TL-WN951N.
View 19 Replies View RelatedI used BT previously without any problems but now use Orange and now using the Internet downstairs is useless(weird flat configuration). The router is upstairs, next to TV(same location as the BT router). I dont know why the wireless Internet signal has become very weak. The only way I can use the Internet if I sit a few feet from the router. Even then, streaming videos on youtube still takes a while compared to BT. This affects all devices using wireless connection - even my Iphone is useless when used downstairs.
Signal interferance/ hacking? Router? Wireless adapter is up to date.
My wireless network signal is great on the first floor, but is weak on the second floor. I have tried different antennas and various locations for the antennas, but with little improvement. I prefer not to purchase signal amplifier. I have a second identical router. Can it be connected to the current router (LAN output) and by way of a cat5 cable, placed on the second floor to boost the second floor wireless signal?
View 8 Replies View RelatedI had an XP machine using a wired connection with a Linksys WRT54GS 2.4GHz router. The only things connecting to it wireless were my wii and my PS3 which were in the next room, less than 15feet away. I purchased a Windows 7 machine for my wife for Christmas, and gave the XP machine to my kids. I moved the modem and router into the kids playroom, and set the Windows 7 machine up for wireless. Now the router is at one end of the house, and the 7 machine is about 45 feet away. The signal strength was never an issue until last week, and now the PS3 and the Win7 machine constantly have weak signal or no signal. I don't know a whole lot about networking. I am willing to move the router and modem to a central location as a last resort, but would like to keep them with the XP machine for our kids to use.
View 6 Replies View RelatedGot a new e1000 after a RMA. The new unit has a very weak wifi signal. I've tried all different channels. It is running in mixed mode. No microwave, blue-tooth or other noise. 4 feet from the router and the signal is down to -90db. Take a few more steps away and the connection is lost.
View 2 Replies View RelatedI just bought new Dell Inspiron n4050 Laptop " Dell Wireless 1702 802.11b/g/n"the wireless signal tooooo weak near the router (less than 10 cm ) !! and i have dell inspiron n5010 and the signal is too strong !
idk if that hardware problem or soft !the driver software is R302726
I have a Linksys E1000 router. The macbook is getting great signal even out in the yard. The PC running Windows 7 and using an AE1000 wireless adapter is only getting 2 bars out of 5. I don't think there's any interference. I can't figure out why the signal strength is so poor.
View 5 Replies View RelatedMy 24" iMac has been running off airport extreme wireless Internet for a few months flawlessly. All of a sudden one day our power goes out.. No problem, reset the system: should be fine. Not the case. Now my iMac can connect to the router but the signal is very weak almost useless and sometimes it won't connect at all. I've tried everything... Diagnostics say it's fine but then other times it says no IP address. Other routers work fine though. And the other computers I'm the building all have perfect connection... What do I try?
View 4 Replies View RelatedI bought TP-link wireless repeaters which i have failed trying to setup to an eircom zyxel dsl modem (ISP provided modem)i set it up as a universal repeater and had it auto latch on to the eircom modem but it just doesnt seem to boost the signal.i have turned all encryption and this doesnt work either. I have setup this situation using a netgear dsl modem and a netgear wireless router which if i remember i made a mac bridge, and it works great..am i wasting my time trying to get a TP-link talking to a cheap isp modem? i was reading an article somebody wrote that was doing the same thing yet the modem wasnt the same as mine, they said they got it working using WDS...and that the tp-link doesnt know about WDS and you need to use telnet to change settings on the tp-link looked a real hassle anyway.
View 3 Replies View RelatedI have tested each antenna separately. With each antenna attached one at a time the left and right antenna is giving me -20 signal. The center is only giving me -65 signal. Is this a problem with the router or normal? I noticed that the center pin is pushed in more then the left and right. Don't know if that is the cause.
View 14 Replies View Relatedit will not connect to the wireless signal and troubleshooter shows "weak signal" but the signal indicator shows full bars
View 2 Replies View RelatedI have been using a Magnavox 5130 BlueRay Player for a several years. Recently, over the last 4 to 6 months, we have experienced connectivity issues with Netflix. My router is on floor 2 in my office, and the signal strength is strong throughout the house. The Wii with Netflix is in the basement, and it never has a connectivity problem; two laptops are used throughout the three levels with no connectivity problems. So why does the wireless connectivity on the blue ray player suffer? It shows a weak signal, yet when I place my laptop next to it, it shows 5 out of 5 signal strength.I thought maybe there was something in the entertainment center that was perhaps interfering with the signal, so I moved it outside and on top of the entertainment center; no fix.
View 3 Replies View RelatedI am researching power adapters versus range extenders to bring the best signal to a new home theater so I can stream Netflix. I don't do much else (gaming etc...) and am not a tech person. I just want to enjoy movies in an area of my house that gets little or no signal. Didi I waste my money buying smart? Can I still do an ethernet connection off the power adapter? Should I put another router there instead--- off the adapter- so I can use the theaters wifi?
View 1 Replies View RelatedWe have cable internet through a wireless router. It seems to be the case that after we have had a router for about a year, my wife begins having trouble with her internet connection; slow speed, no connection, weak signal, etc. Resetting the router and cable modem will fix the problem, but the fix is only for a short time (an hour or a day). We purchase and install a new router, and everything is fine for about a year, then the problems re-emerge.I can't believe that a router "wears out" after a year or so, but that is certainly how it appears.My wife has a Toshiba laptop running Windows 7, I have a Mac, and our son has a Samsung with WIN 7. I don't experience these problems, and my son does not to the extent my wife does. There is obviously something going on with the Toshiba or its interface with the router, but rebooting the computer doesn't have any effect.
View 1 Replies View RelatedI have a DIR-825 in my basement at one end of the house and it works great. My problem is the signal strength is a little weak on the main floor at the other end of the house. I would like to add a second access point to cover that end of the house. Do I need to get another DIR-825 and wire it to the original or is there another option? I obviously don't need all the features of the DIR-825 for the 2nd AP, but I cant find a less expensive option that will still allow me to use both bands.
View 6 Replies View RelatedI am trying to setup two Cisco 1310 bridges (AIR-BR1310G-A-K9-R) for connectivity between two buildings. No external antennas have been setup yet and I am just setting the basic configuration.One is running c1310-k9w7-mx.123-8.JEA3, the other c1310-k9w7-mx.123-7.JA1,setup as a root-bridge, the other as a non-root bridge.However, even after disabling authentication and encryption, both units are still not talking to each other.Maybe a second set of eyes can see an issue?
View 7 Replies View RelatedMy SURF N300 router makes my internet signal very weak, 1/10 of what was contracted but it works perfectly with the cable connected directly to the computer, how can I configure it to work properly?
View 1 Replies View RelatedI have a Belkin N300 Dual-Band Wi-Fi Range Extender but the signal light is always amber and I have difficulty connecting to the N300 wi-fi. Can I use a wired Ethernet cable to connect to it rather than it picking up the existing weak Wi-Fi signal?
View 1 Replies View Related
