Cisco :: Configuring Aironet 1100 Access Point?

Dec 22, 2011

I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?

View 8 Replies


ADVERTISEMENT

Cisco Wireless :: Aironet 1100 Series / IOS Upgrade For Access Points?

Sep 25, 2012

I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
 
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.

View 2 Replies View Related

Cisco Wireless :: How To Connect Macbook Air With 1100 Series Access Point

Oct 10, 2011

how to connect macbook air with cisco 1100 series access point

View 2 Replies View Related

Cisco Wireless :: Aironet 1100 Keeps Rebooting

Jun 30, 2008

I deleted the ios image form the aironet device from command line when i was trying to updgrade it.Now the aironet 1100 keeps rebooting.I've tried to hold down the mode for 30 seconds goes red, but keeps rebooting.

View 2 Replies View Related

Cisco Wireless :: DHCP Configuration On Aironet 1100 WAP

Jun 6, 2013

I have to configure DHCP on Aironet 1100 WAP so wireless client will get IP address through WAP. I tried all the option mentioned in Document but nothing is working.

View 1 Replies View Related

Cisco Wireless :: Configure Aironet 1100 Series AP?

Apr 1, 2013

I have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.

View 3 Replies View Related

Cisco Wireless :: Aironet 1100 BSSID List

May 21, 2013

I'm doing a project on trilateration in which is required to list the BSSID and power levels from the APs, since we have alot of Cisco Aironet 1100 deploye here, could this be a choice ?

My first try is to get these values using snmp, but so far had no luck finding the right MIB. I don't think the console might be useful, will it ?
 
I know  I'm assuming alot, that the Aironet enables for a 'iwlist' dump, and that these values can be retrieved through snmp. But seems something reasonable for them to have, even if I haven't found it.

View 5 Replies View Related

Cisco Wireless :: Aironet 1100 Software Upgrade Fails?

Sep 27, 2011

I'm attempting to update the software on three aironet 1100 from System Software Filename:c1100-k9w7-tar.122-13.JA2 System Software Version:12.2(13)JA2 Bootloader Version:12.2(8)JA To the latest release or the 12.3x family and it fails."the software upgrade was interrupted and was not able to be completed"  I also disabled the Radio braodcast?

View 1 Replies View Related

Cisco Wireless :: Aironet 1100 / 1120 / 1130 Support For IPv6?

May 27, 2012

I find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.

View 3 Replies View Related

Cisco Wireless :: Aironet 1100 Default Username And Password Not Working?

Aug 17, 2011

I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI.  I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck. 

I also have a Cisco Aironet AP1242AG that is doing the same thing.

View 7 Replies View Related

Cisco Wireless :: Aironet 1100 Disassociated Because Sending Station Is Leaving

Oct 9, 2012

We have 5 Cisco Aironet 1100 wireless access points and we are having huge problems in the last few days with them disconnecting some mobile barcode scanners that we have.
 
We have two Aironet's in the top of the factory which work fine and 3 down the bottom which keep kicking the barcode scanners off.  If we use the barcode scanners at the top of the factory they work fine, as soon as we come down to the other 3 WAPs it they keep connecting and disconnecting.
 
We get the following error in the Event log on the access points.Disassociated because sending station is leaving (or has left) BSS On the barcode scanners. [code]

View 1 Replies View Related

Cisco Wireless :: Aironet 1100 Weak Signal With Ipad2 Iphone And Blackberry

Apr 11, 2012

in my company we have 40 cisco aironet 1100 without controller, the signal is good with laptops but is too weak with the iphone's ipads and blackberry.

View 12 Replies View Related

Aironet AIR-AP1252G-A-K9 - Wireless Access Point

Mar 19, 2011

I just picked up a Cisco Aironet AIR-AP1252G-A-K9 Wireless Access Point to mess around with at home and learn IOS.

The unit didn't come with a power adapter or any accessories. Just the bare AP. Does this AP need a controller to work? Can I use it as a standalone AP?

View 2 Replies View Related

Cisco :: Configure Aironet 1040 Access Point?

Oct 27, 2011

I am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below

%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
 
and the ssid is not getting broadcasted. kindly let me what could be the cause.
 
[code]....

View 3 Replies View Related

Home Network :: Set Up Access Point Aironet 1040 Cisco?

Nov 23, 2012

how i can set up access point aironet 1040 cisco?

View 2 Replies View Related

Cisco Wireless :: Aironet 1130AG - Login To Wi-Fi Access Point?

Oct 13, 2010

I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.

View 3 Replies View Related

Cisco Wireless :: Aironet 1040 Access Point Managing

May 22, 2012

We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.

View 5 Replies View Related

Cisco :: 1130 - Aironet Access Point Not Able To Connect By User

Jun 12, 2011

I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.

Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
[Code] .....

View 0 Replies View Related

Cisco Wireless :: Aironet 1310 - Outdoor Access Point

Sep 13, 2012

I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
 
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it.  I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS.  I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?

View 1 Replies View Related

Cisco :: Setting Up Aironet 3500 Series Access Point

Nov 21, 2012

links with information / guidelines for the initial setup for this Access Point?

View 7 Replies View Related

Cisco :: Change WPA2 Key On Aironet 1231g Access Point?

Mar 22, 2012

I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?

View 4 Replies View Related

Cisco Wireless :: Setting Up Aironet 1040 Access Point

Mar 13, 2013

I'm working on setting up an Aironet 1040 Wireless Access Point for my company.  It's my first time setting up something like this, and I've run into a bit of trouble.
 
I created my first SSID easily enough, following the manual and guides online.  I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great.  However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
 
I created VLAN 2, and then another SSID which I linked here.  I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager.  I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'.  I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.

View 4 Replies View Related

Linksys Access Point :: Configuring WAP54G V3.1 Without CD?

Nov 14, 2011

how to set up a WAP54G v3.1 Access Point if you've misplaced the CD?

View 5 Replies View Related

D-Link DIR-655 :: Configuring It As Secondary Access Point?

Sep 15, 2009

I have a DLG-4500 router as my primary router and want to connect a second router (DIR-655) to it as an extention of the LAN to the second floor of my home. I have found instructions on doing this with most other routers, but not DLINK.  In fact when doing the initial configuration and trying to disable the WAN link on the second router by using a bogus IP address string (127.0.0.1) The router won't let me save the change?  What are the steps for configuring a secondary router cascaded to the primary (both wireless) to extend network coverage.

View 13 Replies View Related

Cisco :: Configuring 1200 Access Point / Vlans

May 29, 2012

I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
 
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan? I has 4 VLANs and I want a MAC address has access to a VLAN, but not to another.
 
I used ACLs, but this will block the access to the access point, How to get the mac address will have access to a VLAN, eg no other Vlan?

View 6 Replies View Related

Cisco Wireless :: Aironet 1262N - Access Point Behind Non-Root Bridge?

Apr 9, 2012

I want to connect two buildings. Let's call them Building A (main) and Building B.
 
 „A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
  
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
 
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
 
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
  
My Questions:
 
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?

2. How Do I tell AP03 that it should use AP02 as a gateway to building A?

View 2 Replies View Related

Cisco Wireless :: 1242AG / Maximum Associations In Aironet Access Point?

Feb 12, 2011

I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.

Questions :

1.    What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?

2.       If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point

3.       I there a simulator tool that can be used to simulate multiple wireless connections to an AP

4.       Have anyone tested so many users connected to 1 Access point ?

View 7 Replies View Related

Cisco Wireless :: Aironet 1260 Access Point Work Without Controller??

Dec 1, 2010

I would like to buy Cisco  Aironet 1260 Access Points, i just want to use them independantly so   i want to know do they work without the Wireless LAN Controller? or i  have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.

View 9 Replies View Related

Aironet 1121 - Client Isolation On 1 SSID In Cisco Access Point

Feb 2, 2011

i've been looking for a way to isolate clients on a Cisco Aironet 1121 on a certain SSID, and i cant find anything, tried pretty much everything i coudl remember, but since im no expert on Cisco wireless.

Quote:

Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.

[Code].....

View 3 Replies View Related

Cisco Wireless :: Aironet 2602e Configuration As Standalone Access Point

Mar 19, 2013

I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.

View 2 Replies View Related

Linksys Cable / DSL :: Configuring WAG120N Like Access Point?

May 17, 2010

i have a router to connect on Internet, i need it because it let me use VOIP. I want to use WAG120N like Access Point Wireless because my VOIP router is not wireless.
 
How i have to configure it? What kind of incapsulation i have to use? VOIP router IP: 192.168.1.1
 
If is it possible (and if it is useful) i would to configure WAG120N with 2 IP, first one: 192.168.1.101 (to communicate with VOIP router and to let me go on internet) second one: 192.168.0.1 (to let me have control on it's configuration)
 
My devices will connect to 192.168.0.0 network

View 9 Replies View Related

Linksys Access Point :: Configuring WAP54G As A Router?

Mar 26, 2012

We have network that uses a Cisco router and use a WAP54G to access the network wirelessly.
 
We use static IP address so if someone wants to use the wireless an IP address has to be assigned to it and be manually configured for IP Address, Gateway, Sub Net Mask and DNS.
 
This is becoming unwieldly, but it is safe.  Is there any way to config the WAP54G as a router that would automatically assign an IP address in a range just for wireless devices.
 
Therefore the wireless devices could be set up as DHCP and we would use WPA/WPA2 encryption with a passkey, instead of just assigning static IP addresses.

View 1 Replies View Related

Linksys Access Point :: WAP2000 - Configuring 3 SSIDs

Mar 21, 2011

I have a rental property with 3 apartments that are sharing the same internet connection. The users are consistantly downloading more than their monthly allowance, and I would like to monitor how much data each apartment's users are downloading.My plan is to purchase a Cisco WAP2000 Access Point and configure 3 SSIDs (one for each apartment). I havent decided if each SSID is to be setup on it's own VLAN.
 
Will I be able to use SNMP to monitor the data that each SSID has downloaded each month? I am happy to use a network management software package (such as PRTG from Paessler) for the actual monitoring itself, but I just need to know if the SNMP in the WAP2000 Access Point will provide the information to begin with.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved