Cisco Wireless :: Aironet 1310 - Outdoor Access Point
Sep 13, 2012
I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
View 1 Replies
ADVERTISEMENT
Sep 16, 2010
We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
View 3 Replies
View Related
Apr 29, 2013
I've got a Cisco Aironet LAP1310AG-A-K9 that I can't access through Internet Explorer or Firefox (multiple versions). I set a static IP in DHCP, I can ping the unit, but I can't browse to the GUI.
View 1 Replies
View Related
Nov 21, 2011
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
View 3 Replies
View Related
Apr 16, 2012
I have two Cisco Aironet 1310. I wonder which is the maximum distance I can put between them, to an acceptable data transmicion to 54 megabytes or less, using thier internals antennas.
View 2 Replies
View Related
Apr 24, 2011
how is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
View 6 Replies
View Related
Apr 24, 2011
Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies
View Related
Apr 5, 2012
Any IOS image for the Aironet 1310? May I have a copy of it. I cant access to Cisco support today.
- C1310-k9w7-tar.124-25d.JA1.tar
- C1310-k9w7-tar.124-21a.JY.tar
View 2 Replies
View Related
Apr 22, 2012
Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies
View Related
Jul 10, 2012
Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.
View 11 Replies
View Related
Mar 19, 2011
I just picked up a Cisco Aironet AIR-AP1252G-A-K9 Wireless Access Point to mess around with at home and learn IOS.
The unit didn't come with a power adapter or any accessories. Just the bare AP. Does this AP need a controller to work? Can I use it as a standalone AP?
View 2 Replies
View Related
Oct 13, 2010
I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies
View Related
May 22, 2012
We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.
View 5 Replies
View Related
Mar 13, 2013
I'm working on setting up an Aironet 1040 Wireless Access Point for my company. It's my first time setting up something like this, and I've run into a bit of trouble.
I created my first SSID easily enough, following the manual and guides online. I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great. However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
I created VLAN 2, and then another SSID which I linked here. I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager. I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'. I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.
View 4 Replies
View Related
Feb 11, 2009
I got 4 aironet 1310 Πbut i don't have password into Enable mode!. I follow this document "Password Recovery Procedure for the Cisco Aironet Equipment.pdf" to recovery password. It succeed reset password to default Πbut it also reset Previous setting to default.
Can I reset aironet 1310 password and keep Previous setting?
View 3 Replies
View Related
Aug 15, 2011
We are experiencing a high amount of retries in one direction between two 1310 bridges with external yagi antennas. What would this indicate? Here is a copy of the linktest:
POOR (102% retries) Time Strength(dBm) SNR SNR Retries
msec In Out In Out In Out
Sent :5000, Avg 5 - 66 - 64 31 45 Tot: 56 10149
[Code]....
View 2 Replies
View Related
Apr 9, 2012
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
View 2 Replies
View Related
Feb 12, 2011
I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.
Questions :
1. What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?
2. If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point
3. I there a simulator tool that can be used to simulate multiple wireless connections to an AP
4. Have anyone tested so many users connected to 1 Access point ?
View 7 Replies
View Related
Dec 1, 2010
I would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies
View Related
Mar 19, 2013
I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies
View Related
Dec 30, 2012
we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies
View Related
Feb 12, 2013
In our office, we have 3 Cisco Aironet 1140s and they are configured as follows:
* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
how to have the Repeater connect to Access Point A only?
View 3 Replies
View Related
Jul 15, 2012
We are in need to perform a site survey with the Aironet 1041N Access Point.
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?
View 2 Replies
View Related
Jan 17, 2013
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
View 1 Replies
View Related
Oct 14, 2012
Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".
View 16 Replies
View Related
Mar 15, 2011
I have configured a Aironet 1310 bridge as a WGB and is connected to a Aironet 1242AG AP wirelessly!A sensor(IP device) is wired into the 1310WGB. The sensor needs MULTICAST to operate!I checked the DETAILED STATUS of the RADIO and both the 1310 and 1242 are blocking multicast!The RELIABLE MULTICAST TO WGB option is enabled on the 1242AP already!
View 1 Replies
View Related
Dec 22, 2011
I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?
View 8 Replies
View Related
Oct 27, 2011
I am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below
%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
and the ssid is not getting broadcasted. kindly let me what could be the cause.
[code]....
View 3 Replies
View Related
Nov 23, 2012
how i can set up access point aironet 1040 cisco?
View 2 Replies
View Related
Jun 12, 2011
I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
View 0 Replies
View Related
Nov 21, 2012
links with information / guidelines for the initial setup for this Access Point?
View 7 Replies
View Related
Mar 22, 2012
I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies
View Related
Feb 2, 2011
i've been looking for a way to isolate clients on a Cisco Aironet 1121 on a certain SSID, and i cant find anything, tried pretty much everything i coudl remember, but since im no expert on Cisco wireless.
Quote:
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
[Code].....
View 3 Replies
View Related
