Cisco Wireless :: Configure 1310 Point-to-point Bridge (AIR-BRI1310G-A-K9-R)
Apr 24, 2011Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies
ADVERTISEMENT
Cisco Wireless :: 1310 Point-to-point Bridge In Lightweight Mode?
Apr 24, 2011how is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
Cisco Wireless :: AP1242G Point-to-Point Bridge Configuration?
Mar 16, 2013I have two Cisco AP 1242G and i'm trying to configurate a Point-to-Point Bridge Configuration to connect two wired LAN. Figure 1.8 [URL] I would connect two wired networks.
I tryed two configurations: Root and Non-Root AP. This way every wired PC on the Root AP can connect to the Access points, but cannot connect to the wired PC on the Non-Root AP.AP and WGB. Even this way the wired computers on one AP cannot connect to the wired PC on the WGB. This way only the wireless client can connect to the wired network. This is my network:
Root Bridge Non Root Bridge
10.0.0.1 10.0.0.2
Wired clients on the RB Wired clients on the Non RB
10.0.0.100 10.0.0.200
Cisco Wireless :: Aironet 1310G - Point To Point Bridge
Oct 14, 2012Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".
View 16 Replies View RelatedRadioLabs GS2000 Point To Point Wireless Bridge?
Feb 1, 2011This is the first outside bridge I have ever attempted. These radios are 2000 feet apart, pointed at one another. The first radio has a cat 5 (with POE) to a Windstream 2Wire wireless router.
The other radio has 3 RadioLabs AP's (with POE) connected to it. I have followed the installation guide for the GS200 ( Here) to no avail. I must have missed something but don't know what.
Cisco Wireless :: WAP 4410N Network - Configure One As Access Point And Rest As WDS Bridge / Repeater
Sep 5, 2011I have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedD-Link DIR-601 :: Configure In Bridge Mode As An Access Point?
Aug 23, 2011My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies View RelatedCisco Wireless :: Aironet 1310 Bridge - Cannot Access GUI To Configure
Nov 21, 2011I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
Cisco WAN :: HWIC 4ESW Need To Configure Point To Point Data Dual Leased Lines
Jan 18, 2012We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View RelatedCisco Wireless :: Aironet 1310 - Outdoor Access Point
Sep 13, 2012I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco WAN :: 3845 / How To Configure Vrf For Point To Point Link
Mar 11, 2013i have cisco 3845 router,how to configure vrf for point to point link .
View 1 Replies View RelatedCisco Routers :: Join Network With RV016 To Network With RV082 Via Point To Point Air Bridge
Apr 19, 2012Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
Cisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedCisco Wireless :: Aironet 1310 - Infrastructure Access Point Unreachable For Management
Sep 16, 2010We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
View 3 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedCisco Wireless :: Bridge Joined By WAP 4410n For Access Point
Oct 21, 2012I wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies View RelatedCisco Wireless :: 4410 N Access Point Bridge Mode?
Jul 14, 2011We have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies View RelatedCisco Wireless :: 1262N - Access Point Bridge Configuration?
Mar 5, 2013I have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid. I have enble both dott11Radio interfaces on each access point. The problem I am having is that they do not associate. I have not configured them for any encryption or security. I just want to make sure the connect before I add any other configuration. Is there anything else that I need to configure to make them associate.
View 1 Replies View RelatedD-Link DIR-655 :: Using As Wireless Repeater / Access Point / Bridge To Connect
Apr 12, 2011I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies View RelatedCisco Wireless :: Point To Multipoint Using 1252a-n As A Bridge And Channel Bonding
Oct 28, 2011I have a project in an industrial environment which requires high speed wireless connectivity between 6 buildings,one central and five remotes.The maximum distance from the central building is 100 meters (take o look at the attachment diagram).I'm thinking of using the 1252a-n or 1262a-n access point to act as a bridge (root mode) at the central building with 3 omni antennas AIR-ANT5160V-R (6dbi) or 1 omni antenna AIR-ANTNV-R (4dbi).For the remote buildings i'm thinking of using 1252a-n or 1262a-n in work group bridge mode with 1 directional antenna AIR-ANT5160NP-R (6dbi).My questions are:
-Has anybody implemented a similar scenario,point to multipoint bridging with channel bonding at 5Ghz?
-How reliable will be the use of 1252 ap in bridge mode?
-The expected total bandwidth/throughput will be 300/150mbps,so theoritical every bridge will have 60/30mbps available bandwidth/throughput?
-Which antenna model do you suggest fot the central building?
Cisco Wireless :: Aironet 1262N - Access Point Behind Non-Root Bridge?
Apr 9, 2012I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
Linksys Wireless Router :: E4200 As Access Point / Bridge Mode?
Sep 6, 2011I have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
Linksys Wireless Router :: E1200 - IP Ranges As Access Point / Bridge Mode
Mar 18, 2013I have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?
View 1 Replies View RelatedLinksys Wireless Router :: Connect To EA6500 In Bridge Mode Acting As Access Point?
Mar 4, 2013How do I connect to the EA6500 once it's in Bridge mode acting as a wireless access point? Checked the posts and some seem to be able to do this but, we cannot.
View 6 Replies View RelatedUsing Access Point As Bridge?
Feb 28, 2011how can i configure my wireless access point to receive internet connection from Wireless tours
View 1 Replies View RelatedHow To Configure Wireless Access Point
Jun 13, 2011I want to know how to configure wireless access point because i got new internet connection in my home i want to share connection with my nighbour so we bring TP-Link wireless access point bought one cable wire connect with switch and another one connect with TP-LINK access point, but it is not working .now we dont know how it will be work.
View 2 Replies View RelatedCisco WAN :: 887 - Configure ISR Wireless Access Point?
May 21, 2011I am trying to configure Cisco 887-W ISR but have hit a stumbling block when trying to configure the wireless access point- or at least the advanced features of the access point using the URL referenced in from the cisco GUI configuration utility (Cisco Configuration Professional ). I do recall previously reading a post which referenced a different URL.
View 2 Replies View RelatedD-Link DIR-655 :: Set As Access Point Or Bridge?
May 8, 2011I like the ease and price of the 655 as well as the range and speed. I was wondering if you can use them as a bridge to connect another building or just add a second as an access point? It does not seem straightforward from the control panel.
View 14 Replies View RelatedHow To Configure A Router To A Wireless Access Point
Apr 17, 2011am trying to find the configuration code and steps to configure a router to a wireless access point.
View 2 Replies View RelatedCisco Wireless :: 1024N To Configure Access Point
Oct 25, 2012I am attempting to configure a Aironet 1042N AP From my understanding it does not have an IP out the box. I attempted to access the console which I can view it booting up but then it hangs on.
View 1 Replies View RelatedHow To Configure Wireless Access Point To Linksys Router
Jan 18, 2011How do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View Related
