I have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 RepliesI wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies View RelatedI have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies View RelatedJust bought a new router and repeater for a wifi hotspot i am currently running.. I thought i was havng problems with the repeater after i change from router to a server, (and i'm now using a router in bridge mode) so the server is managing all the dhcp.. etc, Hence, the router is Running as an access point. The server which is a Hotspot Server does the rest. For some reason, repeaters, do connect to the access point apparently, but when connecting the client to the repeater (instead of access point) I can't get internet access. although i do get access to the repeater setup.and access point setup too.. or if that is the fact that repeaters must be connected to a router, not access point? should I use it as a WDS? or AP-wds? I have a Cisco Lynksys e1200 router (which i'm using as access point) and an Encore ENXWI-1AN45 3 in one range extender?
View 2 Replies View RelatedI'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
View 5 Replies View RelatedI'm trying to find the maximum number of mac filters that are supported on the Cisco 4410N access point. The datasheet says that it supports mac filtering but does not indicate the maximum number of filters.
View 3 Replies View RelatedMy apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies View RelatedConfigure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies View RelatedI am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop
I have a fairly large home (>5000 sq ft) with multiple levels and some "dead spots" in the extreme areas. I would like to have a fantastic wi-fi signal through the home for access to my home network for my family and internet for guests. I have Fios with a 50/20 mpm with a "g" router. I also have purchased 2 repeaters (ampedwireless.com) and installed 1. Recognizing that it appears to have created a different network, so this isn't what I want to do. Then I went back and purchased 2 access points. I need to have an "hardware solution" in my theater (basement) as well as in my bedroom (3rd floor).
View 1 Replies View RelatedLimit his bandwidth. but he will only be staying till the end of summer. The new roomie then might be a torrent monkey.Completely shield my other computers from his sight, so to speak. Like I said he's not a hacker but the new roomie might be.
I'd like the router (linksys WRT54G v3 runner latest linksys fw) and the rest of my network (main PC and media server) to be resistant to at least a script kiddie, and hopefully against a intermediate hacker.I'm currently using wifi with WAP2 personal as the router security.
I would like to configure 3 Access Point (WAP4410N) to extend the wifi in my house. I try it to do several configuration but it doesn't work.
In this configuration, the wifi devices disappears and re-appears constantly. I lose the IP addresses and they all come down only every 5 seconds. I made screen shots of the 3 terminals in the word document attached below
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
We just got a new replacement router at our home. We had a 2wire 2701 HG-S (we got this for free when we signed up for our DSL service) and now replaced it with a Netgear N300 Work and Play model. I want to know if we can set up the 2wire router as another access point to improve our wireless signal range. Right now we have a good signal upstairs (where the Netgear router is located), but not the best signal downstairs. I am able to run an Ethernet cord from the Netgear router downstairs to the 2wire if necessary, if it will improve our WiFi signal. Both of these routers are router/modem combos that include the DSL modem, in addition to wireless access point btw. Is this even possible to do? Would it require me to install a custom firmware onto the 2wire router?
View 10 Replies View RelatedI have a Sitecom WLR 4000 wireless router. I also have a Linksys Wireless G Accespoint. Can I use that AP as a extender/repeater for the Sitecom router? If yes, how to configure one and other?
View 4 Replies View RelatedWe have a wireless network and would like to extend the range for it and I was told that a E2000 could be setup to extend the range.If we say that our existing wireless network has the SSID network1, can the E2000 be setup so that it is connected to a LAN socket and then wok as a wireless runter with the same SSID (network1) so that pc's can connect easily ?Or must the two wireless routers be connected with a dedicated cable ?Or must I setup the new E2000 up as a new wireless network with a new SSID like network2 ?
View 3 Replies View Relatedhow to configure Cisco 1252-AG-A-K9 Access Point Root and Repeater?
View 9 Replies View RelatedI just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies View RelatedI have just installed 3 access points along with 6 repeater access points all running V12.4. They are all AIR-AP1242AG-E-K9 using the 2.4GHz radio.
Prior to installation I bench tested that the repeaters would associate with the access points and if one of the access points was turned off the repeaters would automatically roam to another access point. I did not have all 9 devices powered up at the same time, but did have 2 repeaters and 2 access points powered up to simulate association and roaming.
During installation as access points and repeaters were powered up everything behaved as expected (repeaters were associating to access points etc.) however during installation once everything was installed the 3 access points were all powered down for half an hour or so and once powered back on the repeaters did not automatically re-associate until they were re-booted.
I have now configured the repaters with parent MAC addresses to reflect the above current assocaition pattern but not yet powered off the access points to test if this forces re-association as this is now a live operational site!!
Is it normal to have to re-boot the repeaters if ALL 3 access points are powered down at the same time? i.e. If only one access point is powered down will the repeaters automaically roam to another access point o.k.?
In our office, we have 3 Cisco Aironet 1140s and they are configured as follows:
* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
how to have the Repeater connect to Access Point A only?
Bought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedWe have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies View RelatedI have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid. I have enble both dott11Radio interfaces on each access point. The problem I am having is that they do not associate. I have not configured them for any encryption or security. I just want to make sure the connect before I add any other configuration. Is there anything else that I need to configure to make them associate.
View 1 Replies View RelatedAs per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.
I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
I'd like to give my DIR-655 (rev. A4, firmware 1.32) to my brother for use as a repeater, to work with the weak signal in his apartment. But I don't see any way to configure the device to join an existing wireless network. Am I wasting my time?
View 7 Replies View RelatedI have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
I have a WAP54G as my access point, currently it is connected with my BEFSR81 router. I am thinking of changing the access point to a WAP610N for the house. I know that this would work but I was wondering if the WAP54G could be used as a repeater for the outside (I know a lower speed). I know they are two different channels but I wanted a larger range for my wireless. I am on Windows XP, SP2, using Firefox. Can this be done?
View 4 Replies View RelatedI have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?
View 1 Replies View RelatedI want to extend the range for a Linksys router WRT160N. I don't have the possibility to use an access point with a wired connection. I read on this forum that can be used WAP4410N configured as repeater, without wired connection. Can someone who has used this solution to confirm that it works? What configuration should be done on the router WRT160N to permit wireless signal to be repeated by WAP4410N?
View 5 Replies View Related