I'm trying to find the maximum number of mac filters that are supported on the Cisco 4410N access point. The datasheet says that it supports mac filtering but does not indicate the maximum number of filters.
View 3 Replies
I wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies View RelatedI have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedI wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.it is necessary to reset the table mac and other resources that are not possible via WEB GUI..I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.It has some important information about this topic, it is necessary to reset the table mac and other resources that are not possible via WEB GUI.
View 1 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedIf you have MAC filter enabled with the E4200 Firmware Version: 1.0.01 you cannot connect to guest.
View 2 Replies View RelatedI have several laptops at home that connect via wireless connection tot he DIR_655. Using the MAC address of those laptops, I want to prevent them from going to certain websites.Under 'Advanced" and "Website Filter", I addes several domain names (websudoku.com for example). I selected "DENY computersaccess to ONLY these sites". I then saved settings.I then went to "Access Control". I clicked on "Enable Access Control".I clicked on "Add Policy" to cdreate a new policy for one of the laptops.When I boot the laptop and go to one of the websites, it still allows me access. The URL/domain name is correct.
View 5 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
The documentation for the 4410N states it supports 802.1x however, all I see is to configure 802.1x using mac address or using uername and password.
Does the 4410N support 802.1x using EAP? If so how is it configured?
I need a power Injector compatible for WAP 4410N.
View 3 Replies View RelatedI would like to configure 3 Access Point (WAP4410N) to extend the wifi in my house. I try it to do several configuration but it doesn't work.
In this configuration, the wifi devices disappears and re-appears constantly. I lose the IP addresses and they all come down only every 5 seconds. I made screen shots of the 3 terminals in the word document attached below
I installed one of these on a small network. It's going through a mini-switch 5 port netgear to a larger 16 port netgear. Users are only able to get (4Mbps, 5Mbps) down on a file transfer. Shouldn't I be able to get closer to 80 Mbps on a 100Mbps network when connected on 802.11N?
View 10 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I’m planning to use Cisco 4410N AP for my new office. I have 20 offices in 1st floor (20 * 15 FT floor size). I want to know is it possible to cover the entire floor using one 4410N AP?
View 3 Replies View RelatedHave a Linksys E-3000 router and a WAP-4410N which I wish to configure as a repeater to extend network coverage. E-3000 IP has been changed to 10.10.1.1. How do I do it ? What do I connect to what in order to configure the WAP-4410N to new settings? It will of course be located remotely from the router. At this time network consists of a main PC and 2 wireless laptops. I have read the manual and it doesn't answer the above described situation.
View 7 Replies View RelatedI have a big problem with my cisco wap4410n .. I have upgrade the firmware of this AP to V2.0.3.3 for supporting multiple SSID after my upgradation is finished ..one time I can able to access the administration page But when I connected to another system the same AP I cannot able to connect through ethernet .The network connection in the system shows connected for one second and not connected for the next second its simultaneously repeating the same ..and still not connecting ..i changed my ip setting to default ie 192.168.1.xxxx and again to old config 192.169.3.xx any way the same instance is showing ..
In the WAP the power led, wireless led , are connected good but the Ethernet led is blinking off on stage.I have many times hard reset the WAP but off no use the same happens .i could not able connect to WAP.This may be the worse case ever seen in wap4410n …
We are on our 2nd 4410N. we monitor the AP with software that graphs the signal strength. the first 4410N would completely dissappear for about 3 to 5 seconds every few hours, that would disconnect users and annoy them greatly. a few weeks after we bought it, we sent it back to Cisco who sent us a new replacement. we have been monitoring the new one and several times an hour strength strength drops about 50DB for about a minute. monitoring is done from about 15 feet away from the AP.
View 1 Replies View RelatedWe installed a new WAP 4401n to extend a network and plugged it into a D-Link mini swtich (5 ports). In about 2 minutes we got no activity on the switch. We pulled power on the mini-switch, waited a couple minutes and re-powewred. No activity. Looks like we blew the switch. Put another mini-switch in and it did the same thing in about 4 minutes.
The WAP4401n is a PoE ready AP. We are checking right now on whether it's a cable wiring problem or an AP problem.I believe we are using the RJ-45 data cable that came with the AP.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedIs it possible to filter remote access VPN traffic on a PIX 501 (like you can on an ASA?)
View 1 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
