Cisco Wireless :: Power Injector For WAP 4410N
Jun 28, 2011I need a power Injector compatible for WAP 4410N.
View 3 Replies
ADVERTISEMENT
Cisco Wireless :: 1252 - WCS Reports AP Draws Low Power - With Correct Power Injector
Jul 21, 2011I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
Cisco Wireless :: Power Injector Compatible With 541n AP?
Aug 2, 2011if the Cisco Power Injector (AIR-PWRINJ3=) is compatible with the 541n AP ? I find info about compatility with other AP models but didn't find any related with this SMB model.
View 2 Replies View RelatedCisco Wireless :: Power Injector For 1310 Bridge
Apr 11, 2013We have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
View 1 Replies View RelatedCisco Wireless :: Cannot Find Power Injector For Wap2000
Jan 12, 2011Not long ago i was bought Cisco wap2000 access point for small business, and now the problem is to find power injector for this device. I am already tried to use AIR-PWRINJ3, but access point did't turn on.
View 7 Replies View RelatedCisco Wireless :: 1602i APs - Power Injector Or Adapter?
Jan 28, 2013We are planning a wireless network using the 1602i APs. Some of our APs might or might not be within the 100m limit from the switches, so we'll be running them as repeaters instead. Right now, we are planning on buying power injectors for everything, but I can't seem to find an answer to this question:
If I'm running an AP as a repeater (no ethernet running back to a switch), can it still receive power from a power injector and a short ethernet run between the injector and the AP? Or will I need to use a power adapter?
Cisco Wireless :: Power 1552e With Proper Poe Injector?
Oct 13, 2012Can I power the 1552e with the proper poe injector if I am not using the ethernet port for backhaul? I want to get power thru poe but use a fiber for backhaul.
View 4 Replies View RelatedCisco Wireless :: WAP4410 Doesn't Just Make A Universal Power Injector
Oct 10, 2011Contrary to the information contained in the link above, these two parts do not play well together. I purchased both and plugged them in and no go. It doesn't even light anything on the WAP. It worked fine when it was on its own 12V DC adapter but not plugged into this injector. What I don't understand is why Cisco doesn't just make a Universal power injector that is essentially a 1 port switch and is 802.3af or 802.3at compatible. Its maddening. It looks like I'm going to have to get an SD208P and waste 6 ports just to get one with the correct POE for the WAP4410.
View 2 Replies View RelatedCisco Wireless :: Normal Boot Time For Aironet 1130AG With Power Injector?
Jun 1, 2012I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
View 5 Replies View RelatedCisco Wireless :: Aironet 1410 Bridge Power Injector Coax Cable Length Limits?
Apr 19, 2011how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies View RelatedCisco Wireless :: Wireless Power Injector For Aironet 1250
Sep 3, 2012I have a cisco wireless power injector for Aironet 1250 but I called Cisco and was told this can't be found in the system.
View 9 Replies View RelatedCisco Wireless :: Does 4410N Support 802.1x Using EAP
Aug 22, 2010The documentation for the 4410N states it supports 802.1x however, all I see is to configure 802.1x using mac address or using uername and password.
Does the 4410N support 802.1x using EAP? If so how is it configured?
Cisco Wireless :: WAP4410n With POE Injector
Nov 14, 2011We are looking at purchasing two of the WAP4410n Access Points to add wireless in one building, and possibly replace Wireless G in another. In our building already configured, we have POEs set up and this has worked to centralize everything that has to be monitored. We would like to do the something with the WAP4410n. With the access points we already have, they are Pre POE so there was only one device that would work. With These they are standard POE, Does that mean I can use any POE Injector that is using this standard?
Also, are problems that first existed these access points being worked out or been fixed? I want these to be minimal attention required since I am the IT person here and I don't work in this building, I work in the other building which is walking distance but I do want to avoid problems if possible.
Cisco Wireless :: How To Configure 3 X 4410N To Extend Wi-Fi
Oct 18, 2012I would like to configure 3 Access Point (WAP4410N) to extend the wifi in my house. I try it to do several configuration but it doesn't work.
In this configuration, the wifi devices disappears and re-appears constantly. I lose the IP addresses and they all come down only every 5 seconds. I made screen shots of the 3 terminals in the word document attached below
Cisco Wireless :: Access Via SSH On WAP 4410N Only Works Via Web GUI?
Jul 17, 2012I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.it is necessary to reset the table mac and other resources that are not possible via WEB GUI..I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.It has some important information about this topic, it is necessary to reset the table mac and other resources that are not possible via WEB GUI.
View 1 Replies View RelatedCisco Wireless :: 802.11N / WAP 4410N Serving At 5Mbps
Oct 31, 2010I installed one of these on a small network. It's going through a mini-switch 5 port netgear to a larger 16 port netgear. Users are only able to get (4Mbps, 5Mbps) down on a file transfer. Shouldn't I be able to get closer to 80 Mbps on a 100Mbps network when connected on 802.11N?
View 10 Replies View RelatedCisco Wireless :: WAP4410N POE - Injector Or Splitter
Apr 13, 2011Can the WAP4410N accept a 48 VDC input from an IEEE 802.3af POE injector or is a splitter required on the AP end to drop the 48 VDC to 12 VDC and utilize the DC input connector on the back of the AP? I would prefer to use only the injector at the switch if the AP can accept the 48 VDC at the ethernet port.
View 3 Replies View RelatedCisco Wireless :: AP541N What POE Injector Are Supposed To Be Used
Jan 30, 2011AP541N wireless AP, what POE injector are you supposed to use?The web site states any enterprise class af POE injector will do, but the AP1131 POE injector does not work with the AP541N.
View 5 Replies View RelatedCisco Wireless :: 4410N Access Point Mac Filter
Mar 10, 2011I'm trying to find the maximum number of mac filters that are supported on the Cisco 4410N access point. The datasheet says that it supports mac filtering but does not indicate the maximum number of filters.
View 3 Replies View RelatedCisco Wireless :: Possible To Cover Entire Floor Using One 4410N AP
Apr 23, 2011I’m planning to use Cisco 4410N AP for my new office. I have 20 offices in 1st floor (20 * 15 FT floor size). I want to know is it possible to cover the entire floor using one 4410N AP?
View 3 Replies View RelatedCisco Wireless :: WAP-4410N Simple Installation Procedure
Nov 19, 2010Have a Linksys E-3000 router and a WAP-4410N which I wish to configure as a repeater to extend network coverage. E-3000 IP has been changed to 10.10.1.1. How do I do it ? What do I connect to what in order to configure the WAP-4410N to new settings? It will of course be located remotely from the router. At this time network consists of a main PC and 2 wireless laptops. I have read the manual and it doesn't answer the above described situation.
View 7 Replies View RelatedCisco Wireless :: WAP 4410n Not Accessible After Firmware Upgraded
May 26, 2011I have a big problem with my cisco wap4410n .. I have upgrade the firmware of this AP to V2.0.3.3 for supporting multiple SSID after my upgradation is finished ..one time I can able to access the administration page But when I connected to another system the same AP I cannot able to connect through ethernet .The network connection in the system shows connected for one second and not connected for the next second its simultaneously repeating the same ..and still not connecting ..i changed my ip setting to default ie 192.168.1.xxxx and again to old config 192.169.3.xx any way the same instance is showing ..
In the WAP the power led, wireless led , are connected good but the Ethernet led is blinking off on stage.I have many times hard reset the WAP but off no use the same happens .i could not able connect to WAP.This may be the worse case ever seen in wap4410n …
Cisco Wireless :: 4410N Constantly Dipping Signal?
May 20, 2012We are on our 2nd 4410N. we monitor the AP with software that graphs the signal strength. the first 4410N would completely dissappear for about 3 to 5 seconds every few hours, that would disconnect users and annoy them greatly. a few weeks after we bought it, we sent it back to Cisco who sent us a new replacement. we have been monitoring the new one and several times an hour strength strength drops about 50DB for about a minute. monitoring is done from about 15 feet away from the AP.
View 1 Replies View RelatedCisco Wireless :: WAP 4410N Wipes Out Mini Switch
Sep 28, 2010We installed a new WAP 4401n to extend a network and plugged it into a D-Link mini swtich (5 ports). In about 2 minutes we got no activity on the switch. We pulled power on the mini-switch, waited a couple minutes and re-powewred. No activity. Looks like we blew the switch. Put another mini-switch in and it did the same thing in about 4 minutes.
The WAP4401n is a PoE ready AP. We are checking right now on whether it's a cable wiring problem or an AP problem.I believe we are using the RJ-45 data cable that came with the AP.
Cisco Wireless :: Bridge Joined By WAP 4410n For Access Point
Oct 21, 2012I wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies View RelatedCisco Wireless :: Radios On 1242AG Stay Down With Injector And Cat6509
Apr 18, 2012i noticed that the 1242AG does not bring up the Radios, when there is a Power Injector connected.I see in the Logs of the AP:
%CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C6509 <Switchport MAC Add>
The Module in the 6500 is a WS-X6348-RJ-45 The Option "Power Injector installed" on the WLC is also enabled, with the MAC Address from the Switchport, but no change.When i disable CDP on the mentioned Switch Port and reload the AP, it comes up and runs fine.
Cisco Wireless :: WAP 4410N Network - Configure One As Access Point And Rest As WDS Bridge / Repeater
Sep 5, 2011I have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedCisco :: Finding PoE Injector For WAP4410N?
Aug 26, 2010I bought 2 WAP4410N wireless routers but it did not come with a PoE injector. We do not have a PoE capable switch. I have a couple of 3COM PoE injectors but am concerned about differing PoE standards could cause the 3Com PoE injector to damage the WAP4410N.
I cannot find a PoE injector on the Cisco website. What is the Cisco part number for a PoE injector for the Cisco WAP4410N or provide assurances about the 3COM PoE that I have for the 3COM 3CRWER100-75 access points?
Cisco Security :: Wap 4410N Implementation Of Encryption Wep
Jun 2, 2011How does the implementation of encryption wep wpa etc in hardware cisco wap4410N ?
View 1 Replies View RelatedCisco Routers :: RV016 / RV 082 / WAP 4410N - POE Support
Jan 20, 2010I've looked over all the spec sheets and hunted around, can't seem to figure out if the RV016 or RV082 support PoE. what Cisco product would be best to inject PoE on a small business network. I have 1 RV016, and I'm looking to deploy a RV082 and WAP4410N, with the 4410 being the only device on my network that would need PoE, I'd rather not have to buy a dedicated PoE Switch or Hub just for that one device.
View 5 Replies View RelatedCisco Switching/Routing :: 3750 - Power Stack Has Unbalanced Power Supplies
Jun 9, 2013I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
Cisco Switching/Routing :: Stack-power 3750x / FRU Power Supply Is Not Responding
Sep 4, 2012After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
Cisco Switching/Routing :: WS-C3560-48PS-S Show Power Inline But No Power Available
Apr 14, 2013We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
