I installed one of these on a small network. It's going through a mini-switch 5 port netgear to a larger 16 port netgear. Users are only able to get (4Mbps, 5Mbps) down on a file transfer. Shouldn't I be able to get closer to 80 Mbps on a 100Mbps network when connected on 802.11N?
View 10 RepliesMy WRT610N media server is not serving up large, MKV files (>1GB). I have a 500 GB Maxtor connected with external power.The media server serves smaller files just fine (although they are not MKV files). The disk is formatted as NTFS. I can access the large, MKV files via mapping network drive, so I know they are present on the disk and they are intact; but they media server does not show them.
View 1 Replies View RelatedThe documentation for the 4410N states it supports 802.1x however, all I see is to configure 802.1x using mac address or using uername and password.
Does the 4410N support 802.1x using EAP? If so how is it configured?
I need a power Injector compatible for WAP 4410N.
View 3 Replies View RelatedI would like to configure 3 Access Point (WAP4410N) to extend the wifi in my house. I try it to do several configuration but it doesn't work.
In this configuration, the wifi devices disappears and re-appears constantly. I lose the IP addresses and they all come down only every 5 seconds. I made screen shots of the 3 terminals in the word document attached below
I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.it is necessary to reset the table mac and other resources that are not possible via WEB GUI..I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.It has some important information about this topic, it is necessary to reset the table mac and other resources that are not possible via WEB GUI.
View 1 Replies View RelatedI'm trying to find the maximum number of mac filters that are supported on the Cisco 4410N access point. The datasheet says that it supports mac filtering but does not indicate the maximum number of filters.
View 3 Replies View RelatedI’m planning to use Cisco 4410N AP for my new office. I have 20 offices in 1st floor (20 * 15 FT floor size). I want to know is it possible to cover the entire floor using one 4410N AP?
View 3 Replies View RelatedHave a Linksys E-3000 router and a WAP-4410N which I wish to configure as a repeater to extend network coverage. E-3000 IP has been changed to 10.10.1.1. How do I do it ? What do I connect to what in order to configure the WAP-4410N to new settings? It will of course be located remotely from the router. At this time network consists of a main PC and 2 wireless laptops. I have read the manual and it doesn't answer the above described situation.
View 7 Replies View RelatedI have a big problem with my cisco wap4410n .. I have upgrade the firmware of this AP to V2.0.3.3 for supporting multiple SSID after my upgradation is finished ..one time I can able to access the administration page But when I connected to another system the same AP I cannot able to connect through ethernet .The network connection in the system shows connected for one second and not connected for the next second its simultaneously repeating the same ..and still not connecting ..i changed my ip setting to default ie 192.168.1.xxxx and again to old config 192.169.3.xx any way the same instance is showing ..
In the WAP the power led, wireless led , are connected good but the Ethernet led is blinking off on stage.I have many times hard reset the WAP but off no use the same happens .i could not able connect to WAP.This may be the worse case ever seen in wap4410n …
We are on our 2nd 4410N. we monitor the AP with software that graphs the signal strength. the first 4410N would completely dissappear for about 3 to 5 seconds every few hours, that would disconnect users and annoy them greatly. a few weeks after we bought it, we sent it back to Cisco who sent us a new replacement. we have been monitoring the new one and several times an hour strength strength drops about 50DB for about a minute. monitoring is done from about 15 feet away from the AP.
View 1 Replies View RelatedWe installed a new WAP 4401n to extend a network and plugged it into a D-Link mini swtich (5 ports). In about 2 minutes we got no activity on the switch. We pulled power on the mini-switch, waited a couple minutes and re-powewred. No activity. Looks like we blew the switch. Put another mini-switch in and it did the same thing in about 4 minutes.
The WAP4401n is a PoE ready AP. We are checking right now on whether it's a cable wiring problem or an AP problem.I believe we are using the RJ-45 data cable that came with the AP.
I wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies View RelatedI have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View Related"In the past I have noticed if I have one of my rigs running NAT and DHCP that my ping response times are lower compared to my router DGL-4300, when playing games. Is this due to the PC hardware being superior or is it a software/firmware thing?
Or is there a router out there that will perform better ping response time wise/ lag than my DGL-4300?"
Is this due to hardware or is it software/firmware? My NAT and DHCP box was a windows server 2003 configured with just those roles and my pings were in the 20-30 and I could host/join games no problem and no lag, but when I play through the Dlink DGL-4300 my pings would be 70-90 and some games I had lag issues and host/ join issues, sometimes it would work sometimes not.
I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages. This shows up as a DNS error, stating the DNS lookup failed. If I wait a bit and reload the page, it will sometimes resolve itself. If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue). This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on). I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.
My security setup, if for any reason it matters, is WPA2 with MAC address filtering.
i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
I have several Cata 3500XL switches connected to one 1 HP L3 switch which is connected Sonicwall router. Vlan1 has subnet of 10.10.0.0/24 and Microsoft DCHP server lays inside VLAN1.
Now i want to add VLAN11 (192.168.10.0/24) as second data VLAN but DHCP requests should go to microsoft DCHP server.
This is what i did:
Configured VLAN11 IP on each cisco switch
IP default gateway with IP from other subnet (i guess this is bad since maybe it should be IP of VLAN11 on HP L3 switch?)
Trunk ports are configured to pass everything on cisco switches
On VLAN11 i configured IPhelper IP to be MS DHCP server on each Cisco switch
I haven't tested this yet but i have problem in process.I can't ping VLAN11 IPs between switches (i configured VLAN1 and VLAN11 with IP). When client plugs computer to a port that belongs to VLAN11 will i be sure that client will get IP from the 192.168 range or there is possiblity that he gets IP from the management VLAN range?
How does the implementation of encryption wep wpa etc in hardware cisco wap4410N ?
View 1 Replies View RelatedI've looked over all the spec sheets and hunted around, can't seem to figure out if the RV016 or RV082 support PoE. what Cisco product would be best to inject PoE on a small business network. I have 1 RV016, and I'm looking to deploy a RV082 and WAP4410N, with the 4410 being the only device on my network that would need PoE, I'd rather not have to buy a dedicated PoE Switch or Hub just for that one device.
View 5 Replies View RelatedI have a Netgear WNR3500L wireless router. I assume it's v1 because on the back it doesn't have "v" anything. Firmware version V1.2.2.44_35.0.53NA.When I connect using g I get 22+Mbps download speed. When I connect using n I get 10 Mbps. I've tried using both WPA2 only (laptop reports 130 Mbps connection I believe) as well as the combo WPA+WPA2 (laptop reports connection of 117 Mbps).Broadband download results don't change - they stay at the 10 Mbps level. I've fiddled with some of the settings on my laptop's wireless card - but the results are the same.For now I'm just trying to figure out where I should focus my investigation and fiddling efforts - on the laptop or on the router.
View 5 Replies View Relatedi have a Netgear N600 Wireless ADSL2+ router on wireless a/b/g/n dual band and all that but what i want to know is will i get better performance if i use a WirelessN card over G on a 10 - 15mb/s connection gaming wise and will it b a great increase over the G causeif its not a HUGE increase then i wont waste my money on a newer card?
View 3 Replies View RelatedMy Acer Aspire 5610Z laptop will automatically connect to public hotspot wireless network but when I attempt to connect to a wireless network at home, set up using a Netgear modem, I only ever get 'local' internet connection only. My wife's HP laptop has no problem making the home wireless connection.
View 6 Replies View RelatedI am running windows vista and have installed the software and windows sees the adapter and states it is working but when it searches for available networks it can't find any. How can I download the driver and install it?
View 1 Replies View RelatedI have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies View Relatedoutput are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies View RelatedWe have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
i am placing a formal request to Cisco and to the firmware development team to create a new-and-improved firmware release for the WET200 wireless Ethernet bridge, a product that is still being produced, shipped, and sold. I purchased the product about one-and-a-half years ago and have enjoyed its performance. There have been, however, some flaws with the device, namely the following:While configured to use WPA2-based security, DHCP-related traffic is not passed from a router/gateway's DHCP Server to connected devices on the WET200. Current firmware release notes indicate this was a known issue and was, supposedly, fixed; however, due to the level of problems customers are reporting, it appears this may have only been resolved, if at all, with security configurations of WPA, WEP, or OPEN. It has not been fixed for customers using WPA2-based security.When I originally purchased the WET200 and configured it to use WPA2-based security, while it, initially, did have a few problems connecting to my router/gateway, it, eventually, did connect and stayed connected for, approximately, one year. However, in September of 2009, it suddenly lost connectivity with my router/gateway and has not been able to establish a connection since, even after reinstalling the latest firmware revision and after several soft and hard resets of the device. I tested the WET200 with another router/gateway, only to experience the same issue. Other devices are connecting to my router/gateway, but, not the WET200. The last firmware update for the WET200 was dated back in July of 2008. Currently, it is January 2010 and since these issues have been known for quite some time, it is unacceptable that the firmware for this device has not been updated in such a long time, especially when there are known issues with the WET200's firmware. Such lack of support is forcing me and my clients to stop using these Cisco-based products and purchase competing hardware, something I would prefer not to do; however, without better support, I and my clients do not have a choice. Expecting me and my clients to use an inferior form of security on the WET200, such as WEP and/or WPA, until a firmware update is issued is unacceptable, especially when that update has not been released in over one-and-a-half years. Such lack of support is especially unforgettable when my clients and I are looking to purchase new networking equipment. In the past, I would not have hesitated to purchase a Cisco-based product; now, with this experience in mind, I am finding it very difficult to recommend to a client that he or she should invest their organization's finances into Cisco-branded equipment. Proper, professional, timely, support of your hardware is expected of your customers, especially if you wish them to remain loyal customers. I have noticed that other similar devices, albeit, higher-end devices, have had their firmware updated, more recently, compared to the WET200. I assumed this meant that the firmware development team was updating all firmware on such devices. So far, I have been disappointed in the lack of firmware updates for the WET200. While I understand the possible desire to update the higher-end products, first, as a professional whose job is to research, recommend, purchase, install,configure, secure, and maintain both the enterprise-level and small business-level devices, I highly encourage Cisco not to overlook their small business products when the firmware development team is updating firmware for any Cisco products. Deficiency in the support of one strata of Cisco-based products is reflective upon the support of any Cisco-based product and is not easily forgiven by Cisco customers, such as myself, when new and additional hardware needs to be purchased.
View 15 Replies View RelatedDue to lack of wires we decided to extend our network by using WET546 bridge by linksys. Ideally we looking to create topology like this:
(Computer)--eth--(WET546)---wireless----(AP/WLC2100)---(router)---(Internet)
WET546 successfully authenticates and looks pretty healthy on controller (see below) , however neither of computers plugged to WET546 was unable to obtain ip address from dhcp server , nor working with static ip. I was under impression what it might be related to some default policies on WLC2100. Logs (warning) on WLC2100 looks clean.
This is the first time I am trying my hands on wireless gears. I have 2500 WLC and 1142 AP (which I converted from Standalone to LAP).I have a layer 3 POE switch where i am using port 1 for the WLC which is a trunk port.
Port 2 is for the AP using access vlan 111
Port 3 is trunk port going to a router where i am running dhcp server for the VLANs which are as follow:
VLAN 110 -Corp Wireless (10.1.110.0/24)
VLAN 111 - AP-Mgmt (10.1.111.0/24)
VLAN 999 - Guest (10.1.101.0/24)
I wanted to block the traffic from the Guest VLAN 999 but when i apply the ACL on the Guest Interface created on the WLC, I dont see any pings going across and neither I see any hit counts on the deny statement as if the ACL is never applied.
Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies View Related