D-Link DIR-655 :: Sometimes Not Serving Pages On Wired Connection After Firmware Upgrade
Jan 4, 2013
I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages. This shows up as a DNS error, stating the DNS lookup failed. If I wait a bit and reload the page, it will sometimes resolve itself. If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue). This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on). I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.
My security setup, if for any reason it matters, is WPA2 with MAC address filtering.
View 4 Replies
ADVERTISEMENT
Apr 2, 2012
Last week I upgraded the firmware to 1.13NA and ever since, the wireless network has been slooooooow (wired is fine). If the laptop/ipad/phone is in the same room as the router, things are fine. Anywhere else in the house, the speed drops off to almost nothing even though the signal strength is very good. For example: Under the "Speed" section of my "Wireless Network Connection Status" on my laptop, I'm seeing 150.0Mbps in the same room as the router, 25.0 Mbps in the hallway and 1.0 Mbps about 5 steps further away. All the while, the signal strength is showing Excellent.Speakeasy speedtest: Wired 23.36 Mbps, wireless at the end of the hallway, .12 Mbps.
Hardware version: A1
Firmware version: 1.13NA
Cicso Cable modem DPQ3212
View 5 Replies
View Related
Feb 22, 2011
I tried to upgrade the firmware of my RV042 router. I downloaded the file (RV0XX-v4.0.0.07-tm-20100819-code.bin) and check the cheksum. When I try to upload it, I have the message "413 Request Entity Too Large". How can I do ? Should I unzip the .bin file (it's about 30Mo) ?
View 1 Replies
View Related
Mar 13, 2011
I have been reading posts on this board that state that after upgrading the firmware on a router that you must re-set the router and re-configure your connection. I have just downloaded and installed the latest firmware update for the BEFSX41 (1.52.16.4). When the installation was complete, my network connection dropped out. I then got a "searching for ip address" icon in my notification bar. The connection then completed and my network seems to be running as it should. When I check the set-up screen for the router, it shows the new firmware version. Do I still need to re-set the router? I'm a bit confused by all of this. I have Comcast cable for my isp.
View 2 Replies
View Related
May 10, 2013
I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine. Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
View 1 Replies
View Related
Mar 19, 2011
BEFSX41 Firmware Version to upgrade, version 1 or 2?
I've been using this router since 2006, upgrading the firmware to version 1.52.15 when released in 2007. At that time I think I selected the edition 1 rather than edition 2. Basing decision on the fact that the device had no indication of which model version was correct indicated on the manufacturing labels on the bottom. So I assume edition 1.
Is there any way to tell which hardware release I really have? Maybe by MAC address, or Serial number?
Have not had any problems with the 1.52.15 firmware version, however, I have seen numerous log entries for the following:
2011-03-20 11:45:23 ii=MAX_HTTPSESS2011-03-20 11:45:33 ii=MAX_HTTPSESS2011-03-20 11:45:39 ii=MAX_HTTPSESS
and
2011-03-20 10:53:09 UDP from 202.103.52.147:5060 to nnn.nnn.nnn.nnn : pppp(my ip address & port) followed by 2 to 10 of the following entries:2011-03-20 11:01:33 500 _upnp_Disable
the sending URL indicated as a PRC (Chinese) university with negative traceroute results, nothing really alarming as nothing is getting inside the firewall. Just packets dropped from the senders IP. I am keeping track of the pattern and activity levels.
Will probably just block the whole addy range at the router firewall and PC firewall. AT&T is totally ineffective in blocking this sort of back alley activity.
I've seen only one brief and somewhat dated reference to the "ii=MAX_HTTPSESS" entry and will tackle that issue after updating the firmware to 1.52.16, I haven't found any authenticated tech references for this. I can only make some educated guesses on tweaking HTTP settings.
View 2 Replies
View Related
Jun 6, 2009
I'm trying to upgrade the firmware of a BEFSX41 wired router from version 1.43.3 (apparently the first revision after the original realease) to 1.52.15 (the latest I found), but I can't get it to finish. I'm using a Mac with all the latest versions of OS, Safari, and Firefox. When I use Safari to initiate the upgrade, it get's to the point where it says "Please wait ! Setup will take a few minute _____" and nothing else happens after that, even after waiting 30 minutes or more. When I use Firefox it gets to the same "Please wait" message, then a few minutes later Firefox displays an error message "Connection Interrupted: The connection to the server was reset while the page was loading. The network link was interrupted while negotiating a connection.
View 9 Replies
View Related
Jan 23, 2013
I have one of the network every where routers by Linksys, model NR041. I realize this is an older model but it has been good for me ever since I ought it and I am wanting to find a recent firmware upgrade for this. Is anyone aware of a newer firmware upgrade & if so, where can I find it?
View 1 Replies
View Related
Mar 20, 2013
My BEFSR41 Ver4.2 cannot startup after upgrade firmware to Ver.2.00.4 Build 5. I am sure the upgrade is completed, but the Power light keep blinking after restart. All devices cannot get IP address. The manage page (192.168.1.1) cannot be access even I input a IP address of my NIC manually.
View 2 Replies
View Related
Feb 5, 2011
I have a Dir-655 A3 with the firmware 1.32NA. I cannot get the new firmware 1.35NA to take. The router seems to go through the motions of the upgrade, but at the end, when I log back on, the firmware still says 1.32NA & all custom settings remain.I have upgraded the firmware on this router before and I know that when its upgraded, the router is basically reset to factory settings. All the settings have been backed up and I am attempting this upgrade via a wired connection.
View 2 Replies
View Related
Mar 28, 2012
I have a DIR-655 Rev A4.I followed this forum in the past when there were many problems with firmware upgrades beyon 1.21. Because of this I never upgraded and was told to be satisfied that I can still stay with 1.21 as upgrades caused problems for a number of people.Everything still seems fine with 1.21 except the Shareport utility often does not pickup the printer connection upon booting to Windows Vista. I can always work around this by Disable and then Enable. It will then always find the printer. It is a minor annoyance however.Should I still stay with 1.21 or is upgrading to 1.35 NA recommended ? If I upgrade to 1.35 NA is there a downgrade path back to 1.21 if the upgrade does not work well ?
View 12 Replies
View Related
May 14, 2011
Have the DIR-655 Hardware Version A1. Firmware 1.00NA dated Feb 2010. When I try to upload ANY firmware update from the DLINK site, it says that it is not for that device or is corrupt.
View 5 Replies
View Related
Nov 2, 2011
I have the DIR-655 . I decided to do a firmware update to Firmware Version: 1.35NA and now I having a problem connecting remotely from outside the network to a computer on my LAN. I use a software called Radmin to connect to one of my LAN computers behind the DIR-655 router and now since I did the update I cannot connect because the router is blocking the request, here is the router log info
[code]...
View 2 Replies
View Related
Aug 5, 2011
I have a DIR-615 Ver. C1 f/w3.00. We have been having trouble with the the signal becoming weak or non-existent, so I decided to see if a firmware upgrade would solve the problem. I have attempted to upgrade to DIR615C1C2_FW301B11.bin and to DIR615C1_FW313NAB09.bin with the same result for both of them - with several attempts for each.
The message I get is: "The uploaded firmware file may not be correct. You may have uploaded a file that is not intended for this device, or the uploaded file may be corrupted.
If the uploaded file is correct, it is possible that the device may be too busy to properly receive it right now. In this case, please try the upload again. It is also possible that you are logged in as a 'user' instead of an 'admin' - only administrators can upload new firmware.
The Gateway will not be reprogrammed."
I have disconnected all other devices to reduce traffic, I have attempted the upload multiple times for 3.01 and 3.13NA, I am logged in as the admin, and I believe the files are proper for this hardware version.
Is there something I am missing that prevents me from performing a firmware upgrade?
View 8 Replies
View Related
Jun 25, 2012
Well this one should be in the "Firmware DOs and DONTs" post. I updated to FW 1.11 over wifi and apparently this will corrupt the camera so it needs serviving. Would have been nice to know that before I did it. Since the upgrade from 1.02 1030 I get this note:The throughput of the SD Card on your camera is not currently enough for recording. We suggest you to reformat the SD Card or replace it with a higher class one.
View 12 Replies
View Related
Nov 3, 2010
I wanted to upgrade to the latest firmware (2.03NA). Something went wrong and now the router comes up with the orange light flashing. So the system is in emergency firmware upgrade mode. I set my IP to 192.168.0.2 and connect to the web interface at 192.168.0.1. I see a page with "Firmware Upgrade System" and "Version 1.0.0.2". So far so good. I can now select the firmware and click "send". But then nothing really happens. I can wait for a couple of minutes and then run into a timeout. I tried different browsers (Linux: Firefox, Chrome, etc). I even tried it Windows 7 with IE 8 and I get the same result. It seems that the cgi (192.168.0.1./cgi/index) is not really doing anything?
View 12 Replies
View Related
Feb 6, 2011
I hope that we can get this DIR-825 back from the dead. I did the first portion of the 2.05NA upgrade while wired into LAN1 on the unit, after the reboot the power light went Amber and the unit would no longer respond to pings. I have searched around for various reset methods but have not been able to find a guide or a definitive current D-Link tech manual on how to fix a bad flash. I have tried pinging/arping/web browsing its default IP and the IP I had it set to to no avail.
View 2 Replies
View Related
Jul 17, 2011
I would upgrade the firmware before deciding to replace router with a new one. I noticed there have been several updates to the firmware since I originally installed the router with the current available firmware version of 1.35NA.
View 12 Replies
View Related
Feb 8, 2013
Region : Romania
Model : TL-WR740N
Hardware Version : V3
Firmware Version : 3.8.2 Build 080628 Rel.37228n
ISP :
I have a problem with my tplink router. In first of all I can't find my model in this forum. I have TL-WR641G [108M] and I cant upgrade my firmware.
My current firmware is:
Firmware version: 3.8.2 Build 080628 Rel.37228n
Hardware Version: WR641G/642G v3 081520C2
I tried to download the latest firmware from this page (V4) [URL] I press browse button from web interface, I select wr641gv4-en-up.bin and I press Upgrade but nothings happened. I read on other forums this router have 1MB internal memory and wr641gv4-en-up.bin have 1.07MB.
View 3 Replies
View Related
Nov 4, 2012
Region : India
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL EVDO
I have one BSNL EVDO data card which was working fine before firmware upgrade to latest 3.14.2 Build 120822 Rel.57775n. Now it is keep on saying device unplugged after identifying the device. The device is working fine while connected on my laptop.
View 14 Replies
View Related
Feb 18, 2013
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 100722
ISP : Talk Talk
I've downloaded the firmware update 111125 and followed the instructions. The progress bar reaches 100% but the router doesn't seem to restart (judging by the status lights on the front). It does ask me to log back in but when I check the firmware version, it still reads 100722. I also tried factory default settings after the update. Still it reads 100722. I've tried the update 3 times now.
View 3 Replies
View Related
Sep 30, 2012
I up graded to latest f/w. Now I can only log into the unit for about 1 minute before a get a limited connectivity warning, then it boots me out.
View 7 Replies
View Related
Feb 12, 2011
I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies
View Related
Mar 15, 2011
DIR-655 RevA4 - upgraded to 1.35NA, which is shown on http://192.168.0.1/
When I try to re-log in as Admin, I get a message of invalid password. I have unplugged to reset, but still cannot get back in.
View 3 Replies
View Related
Dec 25, 2011
first one had to get rid of because just wouldn't work with a 3CX server, anyway, I have a DIR-655 A4 factory shipped with 1.32NA I am trying to update the firmware to 1.34NA but it will not let me. It keeps saying Code:
View 6 Replies
View Related
May 12, 2013
I have a DCS-942L. Everything was working fine on my setup until I upgraded the firmware the other day. In the mydlink.com website when I logged in that day, it stated a firmware upgraded was needed. So I clicked on upgrade, let it run its thing and then tried to view the playback and now the thumbnails are just black and when I click on one, it looks like it is loading but then shows the quicktime icon with a question mark over it. I upgraded my Quicktime component and that didn't fix it either. So I went into advanced settings, downloaded the new firmware upgrade from there by saving the zip file and uploading it via the advanced settings website, and still nothing. I have another camera, same setup, that I have not upgraded firmware on yet and that playback is working fine.
View 1 Replies
View Related
Apr 29, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
View 2 Replies
View Related
Feb 10, 2013
Region : UnitedKingdom
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3-14-4 to 3-15-4
ISP : Primus Saver
I had it all working fine, then I wanted to upgrade the firmware. The original firmware was 3-14-4. I downloaded and applied the 3-15-4 firmware. Now when it powers on the power light is on all the time. Immediately the sys, 4, 3, 2, 1, Internet, usb and wps lights flash once. Then about 5 seconds later the 4, 3, 2, 1 & Internet lights flash once, then a second later the cycle starts again. When I connect it to the PC it starts to make a connection on the NIC, but then the router resets. Model: TL-WR1042ND, Ver 1.3 . Is there a way to reset the firmware or get it working again?
View 4 Replies
View Related
Apr 14, 2013
Region : Canada
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP :
I'm wondering if I can install this version of the firmware: TL-WDR3600_V1_130320
It says: Notes: For TL-WDR3600(UN) V1 What is that (UN) version exactly ?
View 5 Replies
View Related
Apr 18, 2012
So let me start by saying that i'm stupid, as i did not 1st read the manual properly and thus upgraded my camera WIRELESS.. (when manual clearly states by cable ONLY).
Camera is now DEAD. Only red led light is flashing.
Hardreboot not working (pushing reset, then switching on camera & hold reset for 30 secs)
Is there anything else that i can do myself or is this gonna be a repair job?
View 2 Replies
View Related
Dec 28, 2011
Region : Bulgaria
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel.53137n
ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1. [URL] Are they suitable for my router?
View 1 Replies
View Related
Dec 20, 2012
My Netgear DGN2200 (Name NetgearCS) won't check for firmware upgrade because it says no connection to internet so unable to connect to the Netgear Servers - Yet this laptop I am currently using (wireless connection is turned off on laptop but not router) is wire connected to this same Netgear router and I have internet connection because I am able to post this enquiry. Note the Netgear DGN2200 router gets its internet connection from my Sky Router and is connected by wire to this Sky Router. FYI my iPhone is connected wirelessly to this Netgear DGN200 router (NetgearCS) and is able to connect to the internet. Do you know why my Netgear DGN2200 cannot check for firmware updates?
View 1 Replies
View Related
May 7, 2012
My Linksys WAG200G worked like a charm in these 4 years, never had connection problems... the firmware was 1.00.09 One week ago i updated the firmware to last version (1.01.09) and now i have slow connection problems, sometimes it doesn't load web pages... I tried to hard reset and I tried to downgrade to different firmwares found on the web (1.01.01 and 1.01.05)What should I do? Is it possible to find the original 1.00.09 img?
View 1 Replies
View Related
