Netgear DGN2200 Won't Check For Firmware Upgrade - No Connection To Internet?
Dec 20, 2012
My Netgear DGN2200 (Name NetgearCS) won't check for firmware upgrade because it says no connection to internet so unable to connect to the Netgear Servers - Yet this laptop I am currently using (wireless connection is turned off on laptop but not router) is wire connected to this same Netgear router and I have internet connection because I am able to post this enquiry. Note the Netgear DGN2200 router gets its internet connection from my Sky Router and is connected by wire to this Sky Router. FYI my iPhone is connected wirelessly to this Netgear DGN200 router (NetgearCS) and is able to connect to the internet. Do you know why my Netgear DGN2200 cannot check for firmware updates?
View 1 Replies
ADVERTISEMENT
Jul 9, 2012
I have a Netgear DGN2200 router/modem and have been having this problem for a while now. Every so often the internet will cut out for roughly 30-60 seconds. There doesn't seem to be any pattern to the connection losses and they can happen at any time in the day (overall it seems to occur every hour and a half, although it can vary). When the internet connection is lost, the little "!" triangle appears at the bottom right. I still have wireless access to the router itself. It also occurs on both my wired computer and the wireless computer. On the Netgear itself, the internet light will either flash rapidly green, or sometimes turn red for a short while. The Netgear is plugged via a splitter into the telephone socket. the old neatgear we had did the exact same thing before it finally died and no longer worked at all. Hence why we replaced it with this one. I also rang AOL about the problem, who said that there may be a problem with the line and that we should ring BT about it. We had the line checked and apparently the line was fine and was not the cause of the problem. Things I have tried include changing the router channel and I have tried changing the splitter in case that was faulty. Do you think it could be a DSL problem on AOL's end? It's possible that the drops coincided with a free upgrade they gave us for faster internet, although time-wise I'm not entirely sure.
View 6 Replies
View Related
Dec 16, 2011
I recently purchased the netgear n300 ADSL2+ modem router. I have tried all day to get it to work, but I have not have any success.
ISP: Verizon (Now frontier I think)
DSL light will be solid green, along with the port, wifi, etc... But the internet one stays solid red.I've tried changing dns settings and things, but to no avail. Though I am able to login to the router, and I can get internet if I directly connect to the modem.
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersRobert>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Robert-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid[code].....
I noticed in the router settings that the internet port had no ip address, as in it was just 0.0.0.0.
View 19 Replies
View Related
Aug 25, 2012
I currently have a Netgear dgn2200 n300 wireless router (acts as a modem, you know all in one thing), and I have configured the settings on it so I can have an open nat type/port forwarded for gaming and so on. I have my xbox and the desktop connected to it via ethernet and my ipod and laptop connected wireless.
The problem is that the internet just drops out for a couple of mins every hour or so whether I or whoever is on it or not. I have tried changing the cables and filter for the phone line but nothing has seemed to work. Occasionally when the internet drops out it doesn't come back on so I have to unplug the router and so on to get it to work.
It's just starting to get annoying getting disconnected so often especially when the router cost like $200 and is supposed to be good for gaming and stuff, and I can't seem to find out why or isolate the problem. My internet download speed is fairly quick (I can get 1.5mb/s say when downloading a movie/hd youtube) and I get 70 GB a month.
View 5 Replies
View Related
Feb 2, 2012
I want to ban a Mac address on this wireless router. [URL]... I haven't really done much in the gateway besides changing password and SSD.
View 4 Replies
View Related
Sep 9, 2012
I am having trouble with my modem/router the netgear dgn2200 n300. I bought it to replace my older netgear modem/router (same model v2 to v3).The problem is I just keep getting disconnected say every hour or so when I am using the internet and sometimes it can disconnect me 2-3 times in half an hour. I have removed the filter/splitter and plugged the dsl cord from the netgear straight into the wall bypassing the filter and I still get disconnected.When I am online I receive great connectivity and I consider the bandwidth to be just fine for my needs.My question is what do I have to do in the settings of the router or in my internet properties for it to stop disconnecting me as it gets frustrating. I will take any advice except for "get a new router" or "do an isolation test" blah. Simply because 1. It happened with my old router and with my netcomm modem. 2. I have already done an isolation test and somethings not configured properly I think so, I am no networking wizard.
View 14 Replies
View Related
Nov 19, 2012
I have a desktop and a laptop connected to one router, my desktop is connected via ethernet wire and my laptop is connected via wireless.
Here's the problem, on my desktop under "Network" in the Windows Explorer, I can see my laptop's name as well as my desktop's name. But when I want to go into my laptop it says "Windows cannot access \<laptop name>".
But, if I go onto my laptop and do the same thing, it works perfectly, no errors, no problems. Both of them have their IPs automatically assigned as well as the DNS server address. Both have File Sharing enabled and both have Network Discovery enabled.
My desktop has Windows 7 64-bit and my laptop has Windows 8 Pro 64-bit. I have tried disabling both firewalls, no luck. I used to be able to connect to my laptop, but now I can't. But I can connect to my desktop through my laptop. My router is a NETGEAR DGN2200
View 3 Replies
View Related
Apr 29, 2012
I am trying to connect a 2nd PC to my Netgear Router DGN2200. The first PC is working normally with full internet capability. I have tried connecting the second with an Ethernet cable but it wont recognise it .
View 7 Replies
View Related
Oct 9, 2012
I cant work out how to get my Netgear DGN2200v3 to port forward.Portforward.com describes how to port forward for a Netgear DGN2200 but NOT for the DGN2200v3.The difference between the DGN2200 and the DGN2200v3 is that when I log into the router and go to port forwarding/port triggering there is no box to fill in the server IP address. It just says service name, service type, starting port, ending port.
View 1 Replies
View Related
Oct 30, 2012
Modem is a Netgear dgn2200
On the modem page with all the settings Under basic settings For connection it says Always Connected The box underneath says idle timeout 5 (that's in minutes)
I am unable to change that number or even get a cursor to appear in that box (I want to change it to a 0 - my internet connection has been dropping out when going idle). I can't right click or anything. That is using Firefox. When I say dropping out, I mean, the 3 computers on the network become unuseable - nothing works and things don't appear to be connected to the internet even though my green ADSL light stays on like it's connected - it is not.
I tried the same modem page in IE, and that box with the 5 in it is still showing 5, but this time it's just grayed out - again, can't be changed. The firmware updates are all upto date (apparently - according to it's check)
View 1 Replies
View Related
Dec 24, 2011
how can i connect a Net gear DGN2200 wireless modem router to a D link DGL4500 wireless router ??
View 1 Replies
View Related
Apr 2, 2012
I have a netgear DGN2200 router with a USB port built in. I also have a WD External Hard drive, When using the hard drive plugged directly into my laptop I get transfer speeds of roughly 20 mb/s,However when I plug the hard drive into the router and transfer wireless i only get 1.2 mb/s.Also I'm looking to get a USB > Ethernet adapter, would this increase transfer speeds wirelessly?If not how do I go about increase transfer speeds?
View 6 Replies
View Related
Jun 15, 2013
I want to public to the internet a web + ftp server, all running in the same machine that now is a performance pc, in the future will be a qnap nas ts-220. I don't need extreme performance so my ISP gives me only 12 Mb down and 0,8 Mb up. I will use the nas as download station, ftp server and a web server when I'll public a personal site.
this is the config:
-modem/router adsl2+ that connects to the internet. ISP gives me dynamic ip! it has 192.168.0.1 ip and I think it cannot be changed.
-a firewall hardware zyxel usg 100 with all active UTM services. it has default ip 192.168.1.1. the netgear in the "attached devices" see the zyxel as 192.168.0.2, the same ip zyxel says to the wan1 port.
-a pc or, in the future, a nas that now has automatically assigned ip 192.168.1.34.
I must use a free or paied service as dyndns or something else. If the solution to retrieve everytime the dynamic ip is to set the ddns only in the router/modem netgear then it can only use dyndns.org or .com or .it with the dns of the associated ddns service. For example: if I set a dyndns.it account in the netgear I must set also the dns provided by dyndns.it because if I set google dns or something else the service cannot work.At the moment I tested only with a filezilla server running on the pc directly connected to the netgear, no zyxel in this test.
The config is:
netgear with ddns service provided by dyndns.it, activated with the username and password, in the wan I setup the dmz as 192.168.0.2, in the adsl settings setup the dyndns.it IPs. in the services of the netgear also provided a custom service with ports from 60000 to 60050 and created two rules one for outbound and one for inbound where I let data pass from the wan to the server in the lan 192.168.0.2.
filezilla running on the pc with windows 7 x64 with lan ip 192.168.0.2 mask 255.255.255.0 as th3 netgear and gateway of course the netgear 192.168.0.1. dns servers same as provided by dyndns.it. filezilla configured with only one anonym user without password for testing, default listening port is 60000, passive mode active with range 60000-60050 and for retrieving IP I set default, no Dyndns.it host cause it will not work.
So configured it works fine!problem is when I connect the zyxel between the netgear and the server.how change the default ip of zyxel? in configuration - ethernet - lan port is correct to set there the default and static ip to 192.168.0.3? there are many options! same as dmz you can set there the static ip and what ip?also when you want to public a server zyxel don't say nothing about port-forwarding. it says only create two address objects one with ip of the netgear and one with the ip of the dmz port then create a rule in the firewall section where you set wan to dmz and destination and origin ip selecting the two address objects previously created then you are ok...no, really no! and the ip of the firewall rules in the netgear? which ip do you must set? 192.168.0.2? or 192.168.0.5 if you set it up in the dmz port of the zyxel? no, it is a conflict so you must set another ip.to set correctly the server to be visible in the internet with the netgear + zyxel usg 100?
View 5 Replies
View Related
Apr 2, 2012
Last week I upgraded the firmware to 1.13NA and ever since, the wireless network has been slooooooow (wired is fine). If the laptop/ipad/phone is in the same room as the router, things are fine. Anywhere else in the house, the speed drops off to almost nothing even though the signal strength is very good. For example: Under the "Speed" section of my "Wireless Network Connection Status" on my laptop, I'm seeing 150.0Mbps in the same room as the router, 25.0 Mbps in the hallway and 1.0 Mbps about 5 steps further away. All the while, the signal strength is showing Excellent.Speakeasy speedtest: Wired 23.36 Mbps, wireless at the end of the hallway, .12 Mbps.
Hardware version: A1
Firmware version: 1.13NA
Cicso Cable modem DPQ3212
View 5 Replies
View Related
May 7, 2012
My Linksys WAG200G worked like a charm in these 4 years, never had connection problems... the firmware was 1.00.09 One week ago i updated the firmware to last version (1.01.09) and now i have slow connection problems, sometimes it doesn't load web pages... I tried to hard reset and I tried to downgrade to different firmwares found on the web (1.01.01 and 1.01.05)What should I do? Is it possible to find the original 1.00.09 img?
View 1 Replies
View Related
Nov 22, 2010
I've been using the WAG54G2 for some time now, recently I set up a range extender and had some issues so one thing I tried was to upgrade the firmware. It was very unclear on this website where to find it (specifically for the G2). I went here but there were 2 files, Annex A or B? [irl].... The instructions are also very unclear on this. But more frustratingly the zip file just contains an ".img" file - no ".bin" as the instructions say. So i tried the manual firmware upgrade using this file and shortly after the message "...whatever you do - do not close the browser or restart the router during the upgrade..." (or similar) the router crashed, so I had to restart it and the browser. Now I think I may have introduced an error as the once perfectly-performing router occasionally drops the internet connection for a few minutes. With my work I need 100% uptime.
View 3 Replies
View Related
Jan 4, 2013
I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages. This shows up as a DNS error, stating the DNS lookup failed. If I wait a bit and reload the page, it will sometimes resolve itself. If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue). This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on). I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.
My security setup, if for any reason it matters, is WPA2 with MAC address filtering.
View 4 Replies
View Related
May 8, 2012
I have a Linksys WRT54GS (v5) router. I noticed that my firmware was outdated and tried to upgrade it tonight. During the upgrade progress, the browser reset the connection and now cannot access my router configuration pages.I did a hard reset. Then I did the 30-30-30 reset.
The reset worked but no matter what I do, I cannot navigate to any readable page within the router. I get the log in box and successfully log into the router. However, the configuration page(s) are all jumbled and devoid of useful information. It almost looks like a web page that needs flash to be enabled. Lots of colors and boxes but no text or links to other configuration pages
I know it's an old router but it has served me well. I would love to reinstall the old firmware (or new!) and copy my saved configuration file back to the router.Is there a way to access the configuration via a command line interface?
View 4 Replies
View Related
May 21, 2011
How do I check to see if my firmware needs updating? I want to connect it to a motorola 2210-02.
View 4 Replies
View Related
Jan 31, 2012
After upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies
View Related
Jan 12, 2012
how can i check if my netgear N300 adapter wna3100 is compatible with apple tv device I was told that I needed a dual band router to play HD movies from itunes (ipad)
View 2 Replies
View Related
Jan 23, 2013
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225
ISP : Rogers
Ever since upgrading my firmware from 120426 to the latest(121225), one of my computer(windows xp, TP-link Nano) is frequently losing internet connectivity.I purchased the router a month ago and firmware 120426 was the version that came installed. The router would stop working about 3-4 times a week, requiring me to reboot it. Because of this I did some research online and found out about version 121225 which supposedly should improve performance and stability. After the firmware upgrade today I noticed that one of my computer is having a lot of trouble maintaining internet connectivity for more than 30 minutes. When checking wireless connectivity it would say that I am connected and that the signal strength is excellent. I'm also able to ping 8.8.8.8 but not www.google.com(I've tried ipconfig /flushdns and it doesn't solve the problem). I also have trouble accessing or pinging the router(192.168.0.1) with this computer.
View 3 Replies
View Related
Aug 14, 2012
I bought a Netgear wnr2000v3 about a year ago and everything was running fine for months. There are 8 devices connected to the router, 3 directly connected, 2 over wifi and 3 passing a switch.
Now, since approx. a month, it happens like once a week that the connection to the modem crashes and I'm unable to access the internet for about 3-4 hours anymore. I'm still able to connect to the router, where it is stated that there's no internet connection. When I connect a pc directly to the modem, everything is fine, so there doesn't seem to be any problems with my ISP.
I updated to the last firmware, tried it out with only 1 device connected to the router, reset factory defaults, rebuilt the physical setup.. Is there a way to gain access to internal log files?
View 1 Replies
View Related
Aug 17, 2011
I use the internet wirelessly via a Netgear JWAGR614 (I guess this is the Japanese-market version of the WAGR614), which works fine with my old laptop, a Toshiba Dynabook running Windows Vista. When I use it to connect with my new laptop, however (also a Dynabook, using Windows 7 32-bit), the connection to the router will freeze every few minutes. (It still claims to be connected, but no data seems to get through.) It will then come back after about 20 seconds, or faster if I disconnect and reconnect manually.The connection of my other PC is not affected during this time, it is still transferring data normally even while the new PC cannot.
View 6 Replies
View Related
Nov 23, 2012
I've been living in the basement of my house. Our router and modem is upstairs and we have a 20 mb/s connection, but I just ran a speedtest from my room and it shows me that my connection is only at 2.47 mb/s, which is really weird. The router is nearly just above my head on the floor above me, so I can't see the problem.
View 3 Replies
View Related
Jan 20, 2011
I live in a college dorm that has pretty lousy internet. There is no WiFi, just 2 ethernet ports per room I own multiple wireless devices, so wifi is basically a must, but with a wireless router the connection is too slow to even play xbox live. A friend of mine mentioned that I could input multiple ethernets into my wireless router, so I was kind of hoping that was somehow possible, even though I am pretty skeptical. I have a Netgear WPN824N router
View 1 Replies
View Related
Jul 16, 2012
Internet connection seems like it drops and comes back up every couple of seconds. Not just little drops, wont load a web page and lag me out of games drop. Usefully only for a few hours at most. But its been a full day this time. Ive been searching all all over the place and nothing is working. So with that I have a Netgear WNA3100 picking up wireless from my land lords up stairs. Not sure their router Id but Im pretty sure the problem is on my end. Ive downloaded and reinstalled updated driver, and I have "excellent" connection all the time, according to windows and netgears software. Ive tried pinging and I only lost one packet once (at yahoo.com) out of probably 100 pings, literally Ive been sitting here for a while, to the ip and some sites.
View 1 Replies
View Related
Apr 15, 2013
Modem: Netgear
Operating system: windows 7 (32 bit)
internet connection: BSNL
Browser: mozilla firefox
In my system some certain pages are not opening or functioning. for eg yahoo, software downloads, show videos, commercial websites.
View 1 Replies
View Related
Jun 27, 2011
Hardware: DIR-615 @ 3.11NA firmware
Wired:
PC windows 7
PS3
Wireless:
1 DELL windows 7
2 HP windows 7 (HPa and HPb)
3 smartphones
Description:Everything wired always works, the dell wireless always works and HPa always works along with all of the cell phones. HPb will connect to the router always, as in it see's the router and connects using AES security. For between 15-30 minutes everything will work correctly, transfer speeds are fast and everything is working. For no reason the laptop will lose "Internet connection" only, NOT the connection to the router. But all of the over devices continue to work correctly, so i know the router has internet connected.i would have to disconnect from the router and reconnect and that gives me another 15-30 minutes of connection. I have checked a load of stuff, but i cannot figure it out. Here is a netBIOS
C:UsersCat>NBTSTAT -n
Local Area Connection:
Node IpAddress: [0.0.0.0] Scope Id: []
No names in cache
Wireless Network Connection:
Node IpAddress: [192.168.0.15] Scope Id: []
[code]....
View 7 Replies
View Related
May 20, 2011
I recently upgraded my internet speed to 10 MB (used to be 5) but the internet speed in my PC got slower.I ran a speed test and the download rate was 2 MB while on my laptop it was 10 MB. My PC is clean of viruses and its connected to the integrated router via cable.
View 5 Replies
View Related
Aug 4, 2011
I live out in the country at the end of a very long copper cable and my internet connection is never great at the best of times. Also live in an old house with thick walls so the family are always complaining about the poor wireless connection.So I bought a new router, netgear DGN3500, which on the whole seemed pretty good out of the box, but now it is randomly dropping the internet connection. Sometimes this is solved by rebooting the router, but just now this didn't do it and only turning it off completely for 30" and turning it back on again gave me back my connection (DownStream Connection Speed 3680 kbps, UpStream Connection Speed 416 kbps - which is as good as it gets on the end of my phone line).
View 12 Replies
View Related
Mar 22, 2012
I have just picked up an ADSL Netgear N150 DGN1000 router as my old router (just some branded old thing from my ISP has started playing up a bit due to age more than anything else) but for some reason it is not seeing my internet connection at all.I've reset it factory default twice and connect to it wirelessly just fine, including accessing the router's setup pages and whatnot. I was going to update the firmware from in there.. but that needs the connection to the internet as well.
My ISP is BE Unlimited (UK ISP) and their old branded modem connects again immediately when I plug that back in so I know it's nothing to do with any of the cables or filters, etc.One thing I have noticed is that on the box for the new router it does say Orange Retail (another UK ISP) on one of the barcodes but the router itself isn't branded, so I don't see this could be a problem but figured it was woth mentioning.
View 1 Replies
View Related
Jun 8, 2011
I built my first computer today (woot!) but I'm having issues using my netgear N300 usb adapter to access the internet.
I am using a DLink router but for some reason I am getting some weird issues.
First of all, after using the netgear usb adapter, my mac address is something like E0-xx-xx-xx-xx-xx with the xx being the other numbers. Is having a macaddress starting with E0 wrong? All the other 5 devices on my router have mac addresses starting with 00.
Secondly, I am getting a 169.xxxxxx ip address. This is really starting to bother me because I can't set it up using DHCP.
View 8 Replies
View Related
