Linksys Wired Router :: Wrvs4400n Firmware Upgrade With VPN?
May 10, 2013
I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine. Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
View 1 Replies
ADVERTISEMENT
Feb 22, 2011
I tried to upgrade the firmware of my RV042 router. I downloaded the file (RV0XX-v4.0.0.07-tm-20100819-code.bin) and check the cheksum. When I try to upload it, I have the message "413 Request Entity Too Large". How can I do ? Should I unzip the .bin file (it's about 30Mo) ?
View 1 Replies
View Related
Mar 13, 2011
I have been reading posts on this board that state that after upgrading the firmware on a router that you must re-set the router and re-configure your connection. I have just downloaded and installed the latest firmware update for the BEFSX41 (1.52.16.4). When the installation was complete, my network connection dropped out. I then got a "searching for ip address" icon in my notification bar. The connection then completed and my network seems to be running as it should. When I check the set-up screen for the router, it shows the new firmware version. Do I still need to re-set the router? I'm a bit confused by all of this. I have Comcast cable for my isp.
View 2 Replies
View Related
Mar 19, 2011
BEFSX41 Firmware Version to upgrade, version 1 or 2?
I've been using this router since 2006, upgrading the firmware to version 1.52.15 when released in 2007. At that time I think I selected the edition 1 rather than edition 2. Basing decision on the fact that the device had no indication of which model version was correct indicated on the manufacturing labels on the bottom. So I assume edition 1.
Is there any way to tell which hardware release I really have? Maybe by MAC address, or Serial number?
Have not had any problems with the 1.52.15 firmware version, however, I have seen numerous log entries for the following:
2011-03-20 11:45:23 ii=MAX_HTTPSESS2011-03-20 11:45:33 ii=MAX_HTTPSESS2011-03-20 11:45:39 ii=MAX_HTTPSESS
and
2011-03-20 10:53:09 UDP from 202.103.52.147:5060 to nnn.nnn.nnn.nnn : pppp(my ip address & port) followed by 2 to 10 of the following entries:2011-03-20 11:01:33 500 _upnp_Disable
the sending URL indicated as a PRC (Chinese) university with negative traceroute results, nothing really alarming as nothing is getting inside the firewall. Just packets dropped from the senders IP. I am keeping track of the pattern and activity levels.
Will probably just block the whole addy range at the router firewall and PC firewall. AT&T is totally ineffective in blocking this sort of back alley activity.
I've seen only one brief and somewhat dated reference to the "ii=MAX_HTTPSESS" entry and will tackle that issue after updating the firmware to 1.52.16, I haven't found any authenticated tech references for this. I can only make some educated guesses on tweaking HTTP settings.
View 2 Replies
View Related
Jun 6, 2009
I'm trying to upgrade the firmware of a BEFSX41 wired router from version 1.43.3 (apparently the first revision after the original realease) to 1.52.15 (the latest I found), but I can't get it to finish. I'm using a Mac with all the latest versions of OS, Safari, and Firefox. When I use Safari to initiate the upgrade, it get's to the point where it says "Please wait ! Setup will take a few minute _____" and nothing else happens after that, even after waiting 30 minutes or more. When I use Firefox it gets to the same "Please wait" message, then a few minutes later Firefox displays an error message "Connection Interrupted: The connection to the server was reset while the page was loading. The network link was interrupted while negotiating a connection.
View 9 Replies
View Related
Jan 23, 2013
I have one of the network every where routers by Linksys, model NR041. I realize this is an older model but it has been good for me ever since I ought it and I am wanting to find a recent firmware upgrade for this. Is anyone aware of a newer firmware upgrade & if so, where can I find it?
View 1 Replies
View Related
Mar 20, 2013
My BEFSR41 Ver4.2 cannot startup after upgrade firmware to Ver.2.00.4 Build 5. I am sure the upgrade is completed, but the Power light keep blinking after restart. All devices cannot get IP address. The manage page (192.168.1.1) cannot be access even I input a IP address of my NIC manually.
View 2 Replies
View Related
May 12, 2013
I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
View 3 Replies
View Related
Jan 4, 2013
I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages. This shows up as a DNS error, stating the DNS lookup failed. If I wait a bit and reload the page, it will sometimes resolve itself. If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue). This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on). I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.
My security setup, if for any reason it matters, is WPA2 with MAC address filtering.
View 4 Replies
View Related
Mar 14, 2009
I'm trying to upgrade the firmware on my BEFSR81 v3 cable router (firmware version 2.45.xxx) on a Mac. I accessed the interface via Safari browser, followed the instructions, got a message saying not to interrupt the process, but it never completed. So I tried it again (downloaded another copy of the firmware update), and same thing. No choice but to interrupt it. My internet connection seems to be working fine, but now I can't access the router via the browser. I don't think the firmware actually updated.
Should I power down the router and then reset it?
View 3 Replies
View Related
Feb 20, 2011
I recently updated the firmware on my BEFSR81 v3.1 but would now like to revert to the previous version.
Where I can find the earlier version? I've got 2.51.4, build 006 Aug 21 2009 and need the one before.
It's not a critical problem, but more of an annoyance. I power everything here off one big switch which goes off overnight. Before the update I'd just switch it all on in the morning and everything would, after a minute or so, work fine. Now, however, I have to power up the router a minute after the modem or it just sits there doing nothing. That's OK when I'm here, but if it's just the wife she can't reach the back to do it.
View 1 Replies
View Related
Sep 22, 2011
I was in the process of upgrading the firmware on my Linksys WRT54G router when a connection interruption occurred. Now, the router will not boot up and I cannot communicate with it.Is there a way to reset the firmware?
View 2 Replies
View Related
Oct 5, 2011
i have a linksys wrt54g ver6 router. i want to upgrade the firmware. so i went to dd-wrt.com typed in my router. then i found it on there list, selected it and upon reviewing it, it sucked ram 8mb flash 2mb. looking through the linksys versions, ver2 was the best one ram 32mb flash 8mb. so can i use ver2 firware on my ver6 router?
View 1 Replies
View Related
Mar 25, 2007
I would like to upgrade the firmware for my WRT54GS V2.1 router however, I only see versions 1.0, 1.1, 2.0, 3.0, etc.. There is no 2.1 listed, so does this mean I can use the v2.0 firmware?
View 3 Replies
View Related
Aug 4, 2012
I just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
View 9 Replies
View Related
Oct 18, 2012
The file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies
View Related
Feb 24, 2013
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies
View Related
Apr 17, 2013
[code]...
This is new EA6500 and The firsttime Setup My EA6500，Download New Ver Linksys Smart Wi-Fi Router Setup,he say Your router was not successfully set up.
View 2 Replies
View Related
Jul 2, 2012
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
View 2 Replies
View Related
Jul 27, 2008
I have a WRT110 wireless router which disconnects suddenly and continuously. In addition, its performance is really poor. The current firmware installed is 1.0.03. I found a new firmware for this model (1.0.04.10) but when I try to install it, I choose the .bin file downloaded from Linksys TechSupp website, click on the "Start Upgrade" button, but I always get the following message "Please designate the path to the firmware".
View 9 Replies
View Related
Jul 31, 2011
I had issues with my router incorrectly resolving URLs. For example, going to facebook.com would gtive me a "wiki does not exist" message. Pinging facebook.com would give me an IP that belongs to wikipedia. The answer was SUPPOSED to be upgrading to v3.0.03.I upgraded and now my router WILL NOT connect to my DSL modem. Oh, it says it's connected and shows the correct IP address for my DSL modem but the gateway is showing 0.0.0.0. Direct connection to my PC works just fine.I have cycled the power on both the router and the DSL modem several times. The DSL modem is working just fine. I have done several IP release/renew on the router. I have reset the router. To no avail. This firmware update (which completed successfully) seems to have killed my routers ability to communitcate with the internet.
View 4 Replies
View Related
Jan 1, 2013
When I attempt to upgrade the firmware, I receive error code 0x82BF010E. It wont allow me to complete the firmware upgrade on my Mac OS X (10.7.5)
View 3 Replies
View Related
Jun 16, 2011
PS Linksis Online Support said they do not have old firmware andgives me some phones to call .. Others have written about the same problem, saying that prior toupgrade with new firmware to be flash with 2.0.14.I need firmware - version: 2.0.14, where to find it?
View 9 Replies
View Related
Dec 22, 2011
My Linksys WRT54G router has been dropping out lately and I've been recommended to update its firmware as it is very out-of-date. Well, everytime I try to upgrade the firmware to it, I get an error message that says "the connection to the server was reset while the page was loading." I'm trying to upgrade the firmware through the router's site 192.168.1.1 under the adminstration tab
View 2 Replies
View Related
Feb 10, 2012
I am trying to upgrade the firmware, your web site requires the version number, my version is V8, your site offers up to 7.2 ?
View 2 Replies
View Related
Aug 24, 2012
I have a wrt54g (8.1) that was acting a little funny so did some googling and followed the instructions to install new firmware. First the installation failed, double checked to make sure I downloaded the correct file (FW_WRT54G_8.1.09.02_US_20071227.bin), did a reset and power cycle. Checked the information again and everything on the router setup completely disappeared.
View 8 Replies
View Related
Jan 9, 2012
There is no “firmware” number after the model and I believe this router has never had a firmware upgrade. However, if I try to download any of the 3 upgrades from the Linksys support site I get the message “firmware not available, sorry for the inconvenience.” Since the suggested solutions to so many problems posted in the forum is to first upgrade the firmware, I find this response with no explanation quite annoying. I am having problems replacing my current hardwired Linksys two port router with the WRK54G wireless 4-port router. Questions regarding that problem I will post under a different topic. For now, how I can get the firmware upgrade for the WRK54G?
View 5 Replies
View Related
Feb 12, 2011
I'm havoing probems with my network "stuttering" and wanted to update the firmware. The RVO82 is currently running v2.0.0.19-tm and I have downloaded the latest; V 4.0.0.0.07-tm and tried to upload it to the router using both Safari and Firefox but the update won't take. I have followed the instructions to go to a fixed ip of 192..168.1.50 and have a connection directly to the router( bypassing the switch) but cannot get it to update.
View 1 Replies
View Related
Jul 15, 2011
recently i have updated my firmware, once it said update complete, my internet shut down. I can get on the internet now, but i cant use my router. I have to run my ethernet through my modem now. I have tried resetting it many many times.
View 6 Replies
View Related
Mar 25, 2009
I am going to this page: [URL] but I can see nothing regarding firmware. The "Download software" link takes me to a page that has QVPN, TFTP utilities, etc, but no firmware.
View 4 Replies
View Related
Mar 5, 2010
A router newbie here. Running XP Pro with Comcast Cable. Want to install a BEFSR41 V2.1 as firewall, and add a second PC later.
Q. Which firmware version is the most up to date?
Q. How do I install the firmware?
Q. Will I need to manually enter any Comcast information?
Q. Is there a step by step installation tutorial?
View 9 Replies
View Related
Jan 29, 2011
I corrupted my BEFSR41 firmware v4.2; is there a way to recover?
View 1 Replies
View Related
Jan 23, 2011
I have what I believe is an original (V1) version of the BEFSR41 gateway/router. The label underneath the device only shows the model number with no version information. Current firmware version on the device is 1.46.02, dated Aug 03 2004.
Can I confirm (1) that I indeed this router is at hardware version 1? If that is the case it appears from your web site that version 1.46.02 is in fact the current and only firmware version for the device and that there are no firmware version upgrades available.
The DHCP software current does not have IP address reservation, which I am interested in adding if possible via firmware upgrade. If not then I have to consider whether I want this feature bad enough to replace the router.
View 4 Replies
View Related
