DGL-4300 - Router Ping Higher Than Built Pc Serving NAT And DHCP
Feb 22, 2011
"In the past I have noticed if I have one of my rigs running NAT and DHCP that my ping response times are lower compared to my router DGL-4300, when playing games. Is this due to the PC hardware being superior or is it a software/firmware thing?
Or is there a router out there that will perform better ping response time wise/ lag than my DGL-4300?"
Is this due to hardware or is it software/firmware? My NAT and DHCP box was a windows server 2003 configured with just those roles and my pings were in the 20-30 and I could host/join games no problem and no lag, but when I play through the Dlink DGL-4300 my pings would be 70-90 and some games I had lag issues and host/ join issues, sometimes it would work sometimes not.
View 11 Replies
ADVERTISEMENT
Aug 22, 2011
Usually, when I connect to nearby game servers I would have 10 - 60 ping. However, recently my NETGEAR CG814WG stops working randomly (The lights are all on, I can connect to it, but there's no internet connection) and I have to reboot it. (I had this router for a bit longer than a year, by the way)Currently I get around 80 - 300 ping connecting to servers in sydney. Ping directly from my router:
Ping statistics:
Pings sent: 25 (4 per second); Replies received: 25 (4 per second)
Bytes sent: 1600 (266 per second); Bytes received: 1600 (266 per second)
25 replies passed verification (0 failed)
Min time: 10 ms; Max time: 400 ms; Avg time: 132 ms; Total time: 6090 ms
When I reboot the router it has low ping (~30) for a minute or two but then the ping increases.
View 1 Replies
View Related
Jan 27, 2013
i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 13 Replies
View Related
Jul 18, 2012
I have several Cata 3500XL switches connected to one 1 HP L3 switch which is connected Sonicwall router. Vlan1 has subnet of 10.10.0.0/24 and Microsoft DCHP server lays inside VLAN1.
Now i want to add VLAN11 (192.168.10.0/24) as second data VLAN but DHCP requests should go to microsoft DCHP server.
This is what i did:
Configured VLAN11 IP on each cisco switch
IP default gateway with IP from other subnet (i guess this is bad since maybe it should be IP of VLAN11 on HP L3 switch?)
Trunk ports are configured to pass everything on cisco switches
On VLAN11 i configured IPhelper IP to be MS DHCP server on each Cisco switch
I haven't tested this yet but i have problem in process.I can't ping VLAN11 IPs between switches (i configured VLAN1 and VLAN11 with IP). When client plugs computer to a port that belongs to VLAN11 will i be sure that client will get IP from the 192.168 range or there is possiblity that he gets IP from the management VLAN range?
View 4 Replies
View Related
Oct 11, 2012
i've got a Dell laptop and a few months ago i started experiencing higher ping on some games and some spikes on the internet, at first i blamed my isp but this has continues since then and my brother has reported no spikes or ping increases in the last weeks. I experience a 120 ping on speedtest.net (on average) to servers that i used to get up to 20 ping on and i experience 200 ping on league of legends servers that i used to get 100~ ping on.My laptop is running on windows 7, using panda antivirus and spybot search and destroy (i uninstalled mcafee).
View 2 Replies
View Related
Apr 10, 2012
We have Four 2960S Switches in Stack. We have created Multiple VLANs. While Pinging from Member PC to Member VLAN IP on Switch, we are getting Higher TTL response & Some ping breaks for One Particular VLAN. While pinging from Member PC to Member PC, we are getting Normal Ping Response.
View 5 Replies
View Related
Mar 28, 2012
I was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
View 1 Replies
View Related
Mar 28, 2012
My WRT610N media server is not serving up large, MKV files (>1GB). I have a 500 GB Maxtor connected with external power.The media server serves smaller files just fine (although they are not MKV files). The disk is formatted as NTFS. I can access the large, MKV files via mapping network drive, so I know they are present on the disk and they are intact; but they media server does not show them.
View 1 Replies
View Related
Jan 1, 2013
I can't connect with my D-Link router 4300 to the modem. It's like my router doesn't recognize the internet connection of my modem because there is no available connection at all, for every single PC in my home ! When I connect a cable to my PC, it works. I can't see the problem because I can't even connect to http://192.168.0.1/. I tried many variations but nothing. It all started because I changed the WPA security to WPA2. Then it restarted my router and nothing worked after. I tried several times to reset my router with the reset button, but nothingHere is the ipconfig[CODE]
View 1 Replies
View Related
Jun 6, 2011
We have 10M internet link and the router is 2620 we want to change it to a higher up......which one would be the best one?
View 1 Replies
View Related
Nov 7, 2011
My internetprovider increased speed from 25 Mbps to 40 Mbps. Providermodem direct to pc via LAN gives indeed speed 40 Mbps. However through router lanport or wireless no higher speed. How comes?
View 2 Replies
View Related
Oct 31, 2010
I installed one of these on a small network. It's going through a mini-switch 5 port netgear to a larger 16 port netgear. Users are only able to get (4Mbps, 5Mbps) down on a file transfer. Shouldn't I be able to get closer to 80 Mbps on a 100Mbps network when connected on 802.11N?
View 10 Replies
View Related
Jan 4, 2013
I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages. This shows up as a DNS error, stating the DNS lookup failed. If I wait a bit and reload the page, it will sometimes resolve itself. If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue). This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on). I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.
My security setup, if for any reason it matters, is WPA2 with MAC address filtering.
View 4 Replies
View Related
Aug 28, 2012
My parents Windows 7 PC has suddenly stopped being able to connect to the Internet. Using the "Diagnose problem" feature in the Manage Network Interfaces panel results in a message claiming that it cannot reach the DNS server and that the connection needs to be reset. Doing so has no effect. It is connected to a DSL router via an ethernet cable.The NIC is set to dynamically receive its IP and DNS settings via DHCP which it obtains from the DSL router. Executing ipconfig from a DOS prompt shows that this is occurring as expected, with an assigned IP of 192.168.2.10. The gateway and dns are set to the IP address of the router, which is 192.168.2.1. Note that I can't even ping the router at 192.168.2.1.I also tried static settings in the available range and tried using open DNS IP addresses.
They also have a laptop which connects to the same router wirelessly using DHCP and it is working fine. Using this laptop, I can log into the router and see both it and the problem PC in the list of connected devices, each with the dynamically assigned IP addresses as seen using ipconfig on each. Unplugging the ethernet cable shows the connection status changing in the list of connected devices in the router. From the laptop, I can ping the router and running ipconfig shows that it obtains the same gateway and dns as the PC and the next available IP - 1292.168.2.11.So this leads me to believe the following:
1- The router, NIC and cat 5 ethernet cable are working fine at the hardware level.
2- The DNS settings in the router are fine, as the laptop works
Perhaps coincidentally, the same day it stopped working they received one of those bogus "This is Microsoft calling" calls claiming their PC was infected, but they had heard of the scam and hung up. Naturally, I started suspecting a virus, but a full system scan using McAffee produced nothing. If it was a DNS changing virus, would I not still be able to ping the router using the IP address?
View 9 Replies
View Related
Aug 23, 2011
A Windows Server 2008 r2 with 2 internet ports. One (IP: 10.0.96.132) connected to company intranet and one (192.168.10.1) as DHCP server connect to several PCs (192.168.10.**) through a switch.The problem is the PCs (192.168.10.**) can ping the DHCP server (192.168.10.1) , while DHCP server (192.168.10.1) can not ping (192.168.10.**).How to configure the server so that all these PCs can access the intranet?
View 4 Replies
View Related
Dec 24, 2011
I have more than 10 PC om my Workgroup, using DHCP on network, but I have one PC alwaws got wrong IP (auto from dhcp), and can't connect even using static IP (status connect, but can't ping to gateway and other IP)Here "ipconfig /all" on one of PC that work. [code]
View 5 Replies
View Related
Jan 21, 2011
My old office uses Cisco 861 as a VPN router, with the WAN side setup to receive a dynamic IP assigned by Time Warner cable. Now we switched to a new office, with TowerStream which provide 4G SLA'ed 10Mbit service with static IP, and I get a Cat 5 ethernet down from it.
So all I did, was to go my "interface FastEthernet4", and typed ip address 173.243.123.123 255.255.255.252.Changed speed to "speed 100" and "full-duplex" (as instructed by the ISP).
I also did "ip default-gateway 173.243.123.124", which is the default gate way assigned by the ISP.I also typed "ip name-server 64.17.123.123" to setup the new DNS, am I doing anything wrong? I can't even use the router to ping google, but if I connect the laptop directly to the outside line, then it works, so I know the outside line is good.
Why can't I connect to the internet? I wasted several hours already trying everything in my book to trouble shoot a supposedly very simple configuration change. Do I need to change something related to NAT when changing to Static IP? My NAT was working just fine before when under DHCP.
The below is my full config (some IPs changed to preserve anonymity):
=============================================
Building configuration...
Current configuration : 16628 bytes
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
[code].....
View 29 Replies
View Related
Jan 28, 2013
I connects to the wireless box and has full signal but an exclamation mark is present.I have run some tests and the IPv4 and IPv6 say they have no internet access.I also run a full test and everything passed except the ping test which failed and it said: no response:default gateway response: dhcp server it suggested disabling security firewall but i'm not sure if that's the correct thing to do or even how to do that!
View 7 Replies
View Related
Jan 10, 2013
I need another set of eyes on my config. I am trying to set up my router for a basic connection for the time being. I set my gig 0/0 port to dhcp I see traffic being sent and recieved but I can not ping 8.8.8.8. I am connected to a basic comcast modem from 0/0 I have also tried setting gig 0/0 to 100 full. I do have IP routing enabled. I believe I have my acl's configured correctly. I am wondering at this point if I need a static block of IP's from comcast.
hostname vpn-router-2901
username ****** password *****
enable secret *****
[Code].....
View 14 Replies
View Related
Mar 2, 2011
Well, I've been using my DGL 4300 as a switch, but now I need to use the wireless capabilities it has. I tried going to 192.168.0.1 but it timed out. I pushed down the reset button in the back and hold it for 15 seconds, tried the IP again and nothing but timeout. I unplugged the power cable, held down the reset for 15 seconds, plugged back the power, and still nothing. I've tried various methods, various IP's, and nothing.
View 1 Replies
View Related
Sep 8, 2012
Time for me to update my router. I have been using a Dlink DGL-4300 for 8 years now and never had a problem with it until now. It can't stream HD wirelessly, so I need to get an N router. What's the cream of the crop these days?
I was thinking of going with the DIR-825 or the DIR-835. How have Dlink's router quality faired over the past few years?
View 9 Replies
View Related
Aug 24, 2012
I have the latest firmware 1.9 I think. Periodically (every other day) nothing can connect to the wireless. I have to power down the device (which usually means the whole network cabinet since that is easiest then flip it back on.) I don't know if this is part of the problem but I have 5 wireless devices that try to connect depending on the time of day. However once this happens none can connect.
View 13 Replies
View Related
Dec 28, 2012
I have no problems when the computer is connected to a router. That's how I'm posting here now. But my router is old and has no QOS. So the sound quality is choppy when I connect the phone to the router. So I tried connecting the phone directly to the cable modem, with the computer using the phone's router for internet. The phone's sound quality is great that way. But then the computer won't connect to the internet.When I hover over the network icon in the systray, it says "Local Area Connection 4 is now connected. Speed: 1.0 Gbps" The phone's router is a gigabit connection. So I think that tells me that the computer is seeing the phone/router and the cables are okay.I just tried to Repair through the network icon. It fails because it can't renew. I checked Window's Event Viewer to see what kind of error that might have created. This is the error:[CODE]
View 16 Replies
View Related
Jun 28, 2011
How to bypass router to modem when the router has a built in modem? So my wireless router has a modem built into it, or is it the other way around: modem with built in router. I'm not sure...But anyway, because I am having such difficulties with the ps3 online, I have been told by many people to try bypassing the router straight to the modem.
View 2 Replies
View Related
Oct 19, 2012
I currently run everything in my house off a D-Link GL-4300 plus a couple of their green switches. If I were to replace one of these switches with an additional router (with Gigabit of course, and wireless N- preferably dual mode), could I successfully add the N capabilities, along with extending the A/B/G range?
View 7 Replies
View Related
Dec 27, 2011
I've had a D-Link DGL-4300 for the past four years now (at least) and in the past month, the WiFi signal it sends out just isn't 'good'. What I mean is, the first time this happened in November, one day all the WiFi enabled devices in my home were connecting just fine. Then quite literally the next day, each device detected a signal in the area, yet they simply couldn't connect. I've refreshed each device (iPhone, laptops, consoles) yet they cannot actually connect to the network even though they pick up the signal.
At first I reset the router and that seemed to work, but only for a day or two before the problem started up again. So then I upgraded to the last (and latest) firmware D-Link has on their site and it looked like the problem was solved for good. But unfortunately, this has started again in the last couple of days. D-Link doesn't provide any tech support for my router because it was discontinued in 2009 so I'm stuck.
View 8 Replies
View Related
May 6, 2011
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
[Code].....
View 3 Replies
View Related
Aug 24, 2011
I recently built a new computer, this computer is running Windows 7 (64 bit), playing games such as World of Warcraft I get from 250-350 ms Latency, on my old Windows XP built hooked to the same router gets about 80ms stable.
View 3 Replies
View Related
Mar 1, 2011
My parents house is basically an old ranch style home that was added on to with a 2 story + basement. So I can only guess at the materials between where the signal is weak and where I have installed a DGL-4300 (Dlink Wired and Wireless gigabit router). It resides in the basement which is directly under the 2 story part of the house and everything on any floor of that section seems to get a good signal.
Admittedly I haven't done a lot of extensive testing since I really don't have much stuff that has wireless connectivity, and the one laptop they have is fairly stationary sitting right on top of the wireless router 2 floors up.....signal strength is always good to it.
However the older section of the house gets a pretty weak wireless signal and now with everything being wifi ready I am going to see about solving it. For instance, I've had a hell of a time connecting an older Zune 2.0 8gb version to the wireless network anywhere in the house, I just assumed it was broken or puking on the wireless security which is some version of WPA I can't recall atm if it's one in particular or set to both. But I temporarily disabled all security to see if it would connect and the router saw the device connect with a 20% signal strength for a bit, then the Zune started puking on connecting ..again.
I figured small device, it might even be broken. But I know the signal strength to the older section is not going to be very stellar anyway because the signal on a direct path has to pass through concrete walls and then a concrete foundation......plus it has cordless phone systems to compete against in that same space is has to travel. And anything the kitchen appliances and such might be interfering with it since it's potentially in the way as well.
So, any low cost solution (less than $50 dollars) I can hook into the existing wired network and will play nice with the existing Dlink router as it's going to remain the boss since it was fairly costly and works fine. To work as an extension of the same wireless network.....
I really don't have a problem with updating firmware, connecting into the device to configure it...or even putting new software on it if the directions are decent. The only thing I really care about is that it is cheap, has the capability to fit my bill. I'd guess it'd need to cover a 50 foot circular span with a strong signal and maybe 75 feet out with a medium strength to make sure there's no too weak spots or close up any potential dead spots due to materials used in construction. Oh and it has to be very stable or be pretty stable and have a remote reboot that'll clear up issues, I used to have a linksys router I had to reboot probably once a week to keep it working but it had to be power cycled. It was in the basement, near the patch panel the house has and it got old enough that I got the Dlink to replace it even though it was still functioned besides the freezing/sluggish performance issues requiring power cycles.
View 3 Replies
View Related
Jun 28, 2012
I've been getting internet from a SMC8014WN Wireless Cable Modem gateway and I've been having sporadic connection issues ever since. I use Wireless USB Adapters on my own computer to connect to it from across a hallway and into another room and the connectivity is not very consistent. [URL]No matter what adapter I use (I have many) I sometimes get "now connected" messages and when I'm playing games like TF2 my connection either spikes, or drops and comes back (I'll get DC warnings and the game will freeze, and then come back in)
View 2 Replies
View Related
Apr 3, 2013
I have a Cisco 1801W router, running a DSL connection with wireless connectivity for a school. This is configured on the fastEthernet0 interface on the 192.168.1.0 network (the router is 192.168.1.1).
I was wondering if it is possible to get the built-in switch (fastEthernet 1-8 interfaces) to be used as a part of the same network (192.168.1.0/24).
Fastethernet0 is connected to the school's main switch (24 port), but we could use a few more ports. I'd love to use the 8 ports on the router.
View 1 Replies
View Related
Jul 9, 2012
I have a double Nat problem with my modem acting as a router while it is connected to my router. This is a problem for me because I like to game online and a double Nat makes this difficult. I know the process of setting my modem in bridge mode but I have a few questions before I do so.
1. If I bridge my modem will this cause me to lose connection, if so then how do I get myself back online?
2. While bridging the modem does my router have to be set to any type of special configuration, if so then what do I do?
My router is a Linksys EA2700 and my modem is a Sagemcom 4300.
View 1 Replies
View Related
Sep 12, 2012
I just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
View 4 Replies
View Related
