I have the latest firmware 1.9 I think. Periodically (every other day) nothing can connect to the wireless. I have to power down the device (which usually means the whole network cabinet since that is easiest then flip it back on.) I don't know if this is part of the problem but I have 5 wireless devices that try to connect depending on the time of day. However once this happens none can connect.
View 13 RepliesTime for me to update my router. I have been using a Dlink DGL-4300 for 8 years now and never had a problem with it until now. It can't stream HD wirelessly, so I need to get an N router. What's the cream of the crop these days?
I was thinking of going with the DIR-825 or the DIR-835. How have Dlink's router quality faired over the past few years?
My parents house is basically an old ranch style home that was added on to with a 2 story + basement. So I can only guess at the materials between where the signal is weak and where I have installed a DGL-4300 (Dlink Wired and Wireless gigabit router). It resides in the basement which is directly under the 2 story part of the house and everything on any floor of that section seems to get a good signal.
Admittedly I haven't done a lot of extensive testing since I really don't have much stuff that has wireless connectivity, and the one laptop they have is fairly stationary sitting right on top of the wireless router 2 floors up.....signal strength is always good to it.
However the older section of the house gets a pretty weak wireless signal and now with everything being wifi ready I am going to see about solving it. For instance, I've had a hell of a time connecting an older Zune 2.0 8gb version to the wireless network anywhere in the house, I just assumed it was broken or puking on the wireless security which is some version of WPA I can't recall atm if it's one in particular or set to both. But I temporarily disabled all security to see if it would connect and the router saw the device connect with a 20% signal strength for a bit, then the Zune started puking on connecting ..again.
I figured small device, it might even be broken. But I know the signal strength to the older section is not going to be very stellar anyway because the signal on a direct path has to pass through concrete walls and then a concrete foundation......plus it has cordless phone systems to compete against in that same space is has to travel. And anything the kitchen appliances and such might be interfering with it since it's potentially in the way as well.
So, any low cost solution (less than $50 dollars) I can hook into the existing wired network and will play nice with the existing Dlink router as it's going to remain the boss since it was fairly costly and works fine. To work as an extension of the same wireless network.....
I really don't have a problem with updating firmware, connecting into the device to configure it...or even putting new software on it if the directions are decent. The only thing I really care about is that it is cheap, has the capability to fit my bill. I'd guess it'd need to cover a 50 foot circular span with a strong signal and maybe 75 feet out with a medium strength to make sure there's no too weak spots or close up any potential dead spots due to materials used in construction. Oh and it has to be very stable or be pretty stable and have a remote reboot that'll clear up issues, I used to have a linksys router I had to reboot probably once a week to keep it working but it had to be power cycled. It was in the basement, near the patch panel the house has and it got old enough that I got the Dlink to replace it even though it was still functioned besides the freezing/sluggish performance issues requiring power cycles.
Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : ISP :Is there a way to disable the router DLNA media server? Media service is stopped in the config page. I've never used it so ideally it wouldn't appear in a PS3, Smart TV, etc.
View 1 Replies View RelatedRegion : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : V1_121225
ISP : Cogeco
I bought the 4300 a week ago - and just recently discovered that you cannot turn off the wi-fi radio using a schedule.
I thought this was "wireless router 101" - since my last three routers had this feature... apparently not with TP-Link.
Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Optus
I note that my 4300 never uses two channels in 2.4 GHz wireless n mode as reported by Inssider. I can see a few other routers on Inssider, one of which uses channel 11+7 ALL the time, though it's not a TP-Link router. Mine sometimes will connect to two channels, thus enabling 300 Mbps, but then quickly drops to 1 channel. I believe this is a firmware fault as I only have 3 or 4 routers in the area of my house and I can't believe this would generate sufficient interference to force the router to run at a lower speed. If the router does behave this way by design, then TP-Link should stop advertising it as a 300 Mbps router as it will almost never operate at that speed.
Well, I've been using my DGL 4300 as a switch, but now I need to use the wireless capabilities it has. I tried going to 192.168.0.1 but it timed out. I pushed down the reset button in the back and hold it for 15 seconds, tried the IP again and nothing but timeout. I unplugged the power cable, held down the reset for 15 seconds, plugged back the power, and still nothing. I've tried various methods, various IP's, and nothing.
View 1 Replies View RelatedI currently run everything in my house off a D-Link GL-4300 plus a couple of their green switches. If I were to replace one of these switches with an additional router (with Gigabit of course, and wireless N- preferably dual mode), could I successfully add the N capabilities, along with extending the A/B/G range?
View 7 Replies View RelatedI've had a D-Link DGL-4300 for the past four years now (at least) and in the past month, the WiFi signal it sends out just isn't 'good'. What I mean is, the first time this happened in November, one day all the WiFi enabled devices in my home were connecting just fine. Then quite literally the next day, each device detected a signal in the area, yet they simply couldn't connect. I've refreshed each device (iPhone, laptops, consoles) yet they cannot actually connect to the network even though they pick up the signal.
At first I reset the router and that seemed to work, but only for a day or two before the problem started up again. So then I upgraded to the last (and latest) firmware D-Link has on their site and it looked like the problem was solved for good. But unfortunately, this has started again in the last couple of days. D-Link doesn't provide any tech support for my router because it was discontinued in 2009 so I'm stuck.
I can't connect with my D-Link router 4300 to the modem. It's like my router doesn't recognize the internet connection of my modem because there is no available connection at all, for every single PC in my home ! When I connect a cable to my PC, it works. I can't see the problem because I can't even connect to http://192.168.0.1/. I tried many variations but nothing. It all started because I changed the WPA security to WPA2. Then it restarted my router and nothing worked after. I tried several times to reset my router with the reset button, but nothingHere is the ipconfig[CODE]
View 1 Replies View RelatedI have a double Nat problem with my modem acting as a router while it is connected to my router. This is a problem for me because I like to game online and a double Nat makes this difficult. I know the process of setting my modem in bridge mode but I have a few questions before I do so.
1. If I bridge my modem will this cause me to lose connection, if so then how do I get myself back online?
2. While bridging the modem does my router have to be set to any type of special configuration, if so then what do I do?
My router is a Linksys EA2700 and my modem is a Sagemcom 4300.
"In the past I have noticed if I have one of my rigs running NAT and DHCP that my ping response times are lower compared to my router DGL-4300, when playing games. Is this due to the PC hardware being superior or is it a software/firmware thing?
Or is there a router out there that will perform better ping response time wise/ lag than my DGL-4300?"
Is this due to hardware or is it software/firmware? My NAT and DHCP box was a windows server 2003 configured with just those roles and my pings were in the 20-30 and I could host/join games no problem and no lag, but when I play through the Dlink DGL-4300 my pings would be 70-90 and some games I had lag issues and host/ join issues, sometimes it would work sometimes not.
I am about to re-install Windows ME on an old Dell Dimension 4300. The computer is connected to the internet via a 2Wire 3600HGV DSL modem/router.
Do I need a software firewall? Or is the router sufficient? Is antivirus software necessary if I don't download anything? It will be part of a local LAN, so I don't want to jeopardize any of the other PCs on the home network.
NOTE: I'm looking to run some older (non-DOS) computer games that don't run well (or at all) on XP and newer systems.
NOTE 2: When I say 'secure', I'm not looking to actively browse the web on the machine. I was curious as to what risks I be facing if I simply had this PC connected to my local network (and thus the internet).
Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies View RelatedI have the WAP11 serial number G3110320414 that does not have a reset switch in the back. How do I get back to factory settings?
View 3 Replies View RelatedMy wireless works fine when I am at home, but when I go into a cafe where there is wireless I need to go through the whole troubleshooting process (takes 3-5 min) to reset the wireless adapter (I think those are the words). In one particular location called Popovers I can seem to get access at all anymore. Whats strange is that whenever I go through that troubleshooting process in other locations, I always get the following message at some point : Cant connect in Popovers When I look at the Windows diagnostic
View 1 Replies View RelatedI had some issues with network and I thought that reseting the modem might work. So I did it, I pushed the reset button thingy, but now I can't connect wireless. There is no network offered in "Wireless network connections", like the reset deleted it. What can I do about this?
View 2 Replies View RelatedI need to reset my wireless password because I forgot it
View 1 Replies View RelatedMy linksys router reset itself. Yes it reset itself. It resets to default paramaters. I had to change the router parameters in the webpage with the wired connection to the router. That works fine, but after a day or say it comes back to default again. I am going crazy, I am sure nobody is pressing the little button on the router. Do I have virus or something or maybe the router is going bad. It's a WRT54G.
View 2 Replies View RelatedI was trying to set up an ad hoc network and toyed around with some of the wireless network settings. The network I was trying to set up didn't quite work out so I tried to set it back to how they were but forgot how they were. Is there a way to delete the Wireless Network Connection and let it create a new one or is there a "standard" setting for this to strictly find a wireless network and connect to it?
View 14 Replies View RelatedI've been having this problem the past 2 days. around 7-7:30pm my motorola sbg6580 will reboot itself every 15m or so the rest of the night.I've checked all my line they are in good condition, I've done the whole pull out all the cords let it sit for 1 minute, I've factory reset it.called the cableone tech support and it even reset while i was on the phone with him. I have a tech coming out tuesday but if it's something i can troubleshoot and fix now i'd rather have that.
View 2 Replies View RelatedI want my wireless to be secure.
View 1 Replies View Relatedcant physically access my wireless linysys router but want to reset it????
View 1 Replies View RelatedI am wondering how to reset the password for my wireless router? I am finding it hard to set up a new pc each time because it seems the password is always wrong. I want to set it to something I will easily remember.
View 2 Replies View RelatedI am needing to reset my password for wireless router. I do not have the previous password
View 1 Replies View RelatedReset wireless network password
View 1 Replies View RelatedI need to reset my 615 remotely. I will have someone on the other end push the reset button. I will then need to have them login to the 615 wirelessly. I'll establish a remote control session to their computer, and then I'll reconfigure the router settings. I know how to reconfigure the router just fine.
1) How long do you press the reset button, the manual says 10 seconds, is that correct?
>> 12 SECONDS
2) Once reset, is wireless turned on by default? I hope so, but the manual shows ENABLE WIRELESS unchecked... is that the default setting? Do I HAVE TO CONNECT VIA LAN CABLE TO "ENABLE WIRELESS" first?
>> YES
3) is the default ssid = "dlink" (no quotes)
>> YES
4) is the SSID invisible by default, or is it visible immediately after RESET?
>> IT IS VISIBLE AFTER RESET
The person on the other side can't access the router with a LAN cable, so once reset, the only way to get into the router will be via wireless; that's why I want to be sure I can do this before we do the reset.
How to reset the Dot11Radio?I have also try to config the power level but it prompt me that the selection is invalid. [code]
View 10 Replies View RelatedI'm very new to WCS and the bloke that configured the bludger has left the company. I'm trying to get into it but I don't have the correct username/password combination.
My query is: How does one do a password reset on a WCS server? Or failing that, is there a way I can ascertain the current unknown password?
I have access to the actual server itself, but not the WCS application. Searching around Cisco.com shows that apparently there is a utility that can be used to reset usernames and passwords however I can't seem to find it. The WCS version is: 4.2.62.11
I'm having a little issue with some Cisco Aironet1242ag WAP's. I receive a call at least twice a month stating that some of the WAP's are not giving out internet connection. What I always do is go to my patch panel and disconnect those WAP's not working and connect them back again so they can power cycle. These WAP's are connected to a Cisco3750g. Once the WAP's boot up, the users can connect to the WAP and connect to the internet.
I don't know if these WAP's are filling up with some information that causes the access points to not connect to the WAN.
normally insert the D-link CD in my computer and then follow the steps. this time in the step that all connectivity was being checked the message appeared that one of the cables (ethernet or the other one) is not connected whereas I am quite sure that they are properly connected and nothing at least as far as I know is wrong.after several times, I could connect to the wirelss connection but actually there was no internetwhen I also tried with cable directly from wall jack to my computer it was also the same case.
View 4 Replies View RelatedI just moved into a new place and I've been having a lot of trouble with the wireless connection. There are 4 other people sharing the wireless and none of them seem to have problems, and my phone connects fine, but my laptop will randomly lose internet access while still detecting the network. When I run the troubleshooter it says it has reset the wireless adapter, and the connection will work again, but sometimes only for a few minutes before it craps out. I don't have access to the wireless router itself, so doing anything with that will require asking the landlady (who doesn't speak English well). I had access fine for the first two days after I moved in. I did install a couple of programs after that: 7-Zip and Flash Player 11.2 (since the newest Flash version crashes my Firefox). I don't know if that could have anything to do with it.
I'm running Windows 7 64-bit on an Asus laptop. After searching around the forum a bit, I followed the instructions in this post and will paste the results here. I don't know if the ping address starting with 206 might be invalid since the post is from several years ago.
C:UsersLindsay>IPCONFIG /ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : Lindsay-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]...
I am the owner of an Asus N53SV series laptop running windows 7 home premium. I factory reset my PC in order to have a "fresh" new year, but now I can only connect to the wireless internet in my house using the ethernet cable. When the cable is unplugged, no networks show up for my laptop. I tried going to this link: ASUSTeK Computer Inc. -Support- Drivers and Download N53SV I downloaded the first wireless driver listed...and it gave me an error that just said "error azureware wireless lan driver"....not a very informative error.
View 13 Replies View Related