Wireless Access Always Needs To Reset
Oct 27, 2011
My wireless works fine when I am at home, but when I go into a cafe where there is wireless I need to go through the whole troubleshooting process (takes 3-5 min) to reset the wireless adapter (I think those are the words). In one particular location called Popovers I can seem to get access at all anymore. Whats strange is that whenever I go through that troubleshooting process in other locations, I always get the following message at some point : Cant connect in Popovers When I look at the Windows diagnostic
View 1 Replies
ADVERTISEMENT
Apr 16, 2013
I have the WAP11 serial number G3110320414 that does not have a reset switch in the back. How do I get back to factory settings?
View 3 Replies
View Related
Feb 19, 2013
cant physically access my wireless linysys router but want to reset it????
View 1 Replies
View Related
Jan 30, 2013
I have a Cisco aironet 3502i access point which I am using with a 5500 Wireless Controller. I was configuring the AP for flexconnect and accidentally enabled PPPoE authentication - but never set configured login details for PPPoE. Now when the AP boots up it tries to use PPPoE but fails - it never even looks for an IP address. I have no way to get the AP connected to the controller again.I tried logging into the AP via console, the AP gives me output but I never get a login, even when I hold down the Mode button during startup.I also tried holding the Mode button and waiting for the AP to boot with its default IP (10.0.0.1) and connecting to the AP via telnet, but I was unable to connect or even ping with my PC on the same network configured as 10.0.0.2.What can I do to set this AP back to defaults, to become a normal DHCP client, and reconnect to the wireless controller where I can reconfigure it?
View 9 Replies
View Related
Dec 19, 2012
I got a refurbished E1000, has been great.
Using it w/ my HP laptop since July, just got Mac book and was trying to use w/ that addition laptop but could not find router password, also 192.168.11 would not let me access w/ password: admin, so I reset the router and renamed it. NOW my HP laptop shows my router connected, BUT will not access internet.
View 3 Replies
View Related
Apr 18, 2012
I just bought an E4200 and it was working perfectly, very easy to install, all that it promises. Then I had an energy peak. For some reason, don't ask me why, I did RESET the router not thru the web nor thru Cisco Connect, but pushing the reset button at the back. I can't access the router anymore ! It keeps asking for a password that is never accepted. I have uninstalled cisco connect and tried again. Nothing. The router is not found. Keeps asking for a password. I tried everything: blan+admin, admin+admin, the password I used to have (provided at the cisco connect uninstall).It seems that the RESET never worked. The router is working thru cables, meaning when I can connect to the internet wired. But the router is never found wireless.How could I update the firmware if the router is not recognized (or if I don't have a username+password) ?
View 9 Replies
View Related
Apr 21, 2013
I have just moved and my ISP is the same ( Comcast) but I'm in a different region of the country. The former service (modem) was a cisco (1 port) that I connected my EA 2700 Cisco router to and it worked like a charm. My IP phones came right up as well. Now I have an modem/router combo (provided by my ISP) and when ever I attempt to connect to my VPN it will give me an error and not connect. I was told by my ISP that I could bridge the router and try that way.Do I need to set up all over again? or have the settings remained. Also I am unable to access my router with admin/password. How do I reset the password?
View 1 Replies
View Related
Jan 13, 2013
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies
View Related
Sep 26, 2011
I had to reset my windows xp back to factory settings so i lost all my files but the important thing is that i cant get internet access. I have a modem and router and it does say on the computer that they working but still have no access. I tried to feasting everything and still nothing. I'm not sure what else i should do. Did my files get corrupted?
View 2 Replies
View Related
May 5, 2012
I have an old WAP54G v3.1 and I want to access the menu but cannot, the IP must have been changed and even resetting does not let me in. What can I do?
View 4 Replies
View Related
Apr 27, 2013
I have a problem with my SG200, maybe more than one.
I tried to update to 1.3.0.59 this morning. It succeeded and the switch was restarted. After the restart I could no longer log into the switch. I tried to reset the switch but it still will not let me log in. I also tried to log into the switch using the forllowing method but I still cannot log in. I unpluged everything, held the reset for at least 30 seconds, waited 3 minutes, plugged a computer in and set it up to see the switch. All worked there and the login page appeared. It still would not take my login dredentials nor wold it that the default credentials. I has access through the switch but connot configure anything.
View 4 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Dec 10, 2012
Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies
View Related
Dec 12, 2012
I have reset the modem but after resetting it I can't go for internet anymore with computer or wifi . And after that I notice that my wifi is not under any security which is free for all.can I know how to fix this problem ?the main problem is mostly that can't go internet after reset it
View 2 Replies
View Related
Nov 23, 2012
After reset to factory settings of my Acer 6930 I have lost my internet access.Tried wi-fi and ethernet but neither find my router.
View 6 Replies
View Related
Jul 22, 2010
My computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies
View Related
May 27, 2011
I access my home computers via teamviewer or logmein. My router is a Wag320n
Sometimes my internet connection is lost and if I'm home, I just reset it and the internet is on again.
But when I am away and the internet connection is lost, I can not access my computer. If only I could reset it, I would be able to access the computers I am trying to find a solution to do this.
Practically when the internet connection is lost, the modem does not get an IP from the ISP right? And when this IP is not assigned, there is no way of connecting to the router itself right? Is there a way of pinging or resetting or accessing a modem that is connected to he phone line? I think it is impossible. Or maybe it is possible via some MAC address search or sniffer or I don't know.
Another option would be to somehow have the modem reset, let's say every hour automatically so that the max time I would not be able to accss my computers remotely would be 1 hour.
View 3 Replies
View Related
Nov 5, 2006
I have taken over maintenance of a customer site from another service provider. I need to reprogram several WAP54G units. I have reset the units with the reset button. However, this does not reset the admin password back to admin.
View 9 Replies
View Related
Mar 8, 2011
I've got a 1941W, and we don't have the password for the access point. I've got access to the router, but not the access point.It's not the default password (cisco) and it's setup to use username/password (rather than just password).How do i reset this device? I'd like NOT to lose the config if possible.
View 1 Replies
View Related
Feb 21, 2012
I have a Motorola SBG901 router. Typing ipconfig showed that 172.18.8.1 is the Default Gateway and this is the URL I always used to access the router login page.
I reset the router today by holding the reset button. Now typing the URL 172.18.8.1 does not work. The router user guide says to go to 192.168.0.1. I have tried this but it also does not work. For both I just get the "problem loading page" in Firefox.
The Internet works fine both with an ethernet connection and wirelessly. My only issue is that I cannot access the Motorola router login page. I could access it fine this morning before I reset the router.
View 6 Replies
View Related
Jan 24, 2013
I reset unplug did everything according from cisco.com it didn't work.Can not go to 192.168.1.245. What next I need to do to make it work.
View 3 Replies
View Related
Mar 23, 2013
I was having some connectivity issues with my network of WAP54G's, so I had a technician come to have them looked at. The technician turned out to be completely clueless, and he messed up one of the APs in the process. He changed its IP address and apparently updated its firmware, but he didn't write the new address down, so now I can't access its administrator panel. I've tried to retrieve the IP address using the setup CD that came with the AP, but it doesn't even see the AP in my network. I've tried to factory reset the AP by holding the reset button for 10, 30 and 60 seconds and unplugging the power cord, but to no avail. It still doesn't bring up the admin panel when I enter the default IP in the browser. I think I've tried everything I could find on the Internet about this problem that didn't involve cracking the AP open, but none of it has worked.
View 4 Replies
View Related
Dec 16, 2012
I have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period...
View 9 Replies
View Related
Mar 18, 2009
I have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...
Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period.
View 10 Replies
View Related
Nov 24, 2008
I just purchased a WAG54G2, setup was simple and easy. After being on for about 16 hours if I login to the device all the settings appear to have been reset to default, although the access point and wireless are still working. After another few hours the internet access stops and device appears to have been reset. No power spikes or reliability problems with power. Contacted Linksys support on three different occasions and they don't have any suggestions that work. Tried a "hard reset" but problem still occurs. No firmware upgrades are available for this device.
View 9 Replies
View Related
Apr 4, 2011
How do you reset a 1252ag access point that has the mode button disabled?
View 2 Replies
View Related
Apr 10, 2012
I have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone
-HP Mediasmart Windows Home Server
-Desktop
-Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP
2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
View 9 Replies
View Related
Nov 5, 2012
Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q
Last reset from power-on
1 Virtual Ethernet interface
52 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
[code]....
View 1 Replies
View Related
Aug 3, 2012
I had some issues with network and I thought that reseting the modem might work. So I did it, I pushed the reset button thingy, but now I can't connect wireless. There is no network offered in "Wireless network connections", like the reset deleted it. What can I do about this?
View 2 Replies
View Related
Oct 10, 2011
I need to reset my wireless password because I forgot it
View 1 Replies
View Related
Aug 24, 2012
I have the latest firmware 1.9 I think. Periodically (every other day) nothing can connect to the wireless. I have to power down the device (which usually means the whole network cabinet since that is easiest then flip it back on.) I don't know if this is part of the problem but I have 5 wireless devices that try to connect depending on the time of day. However once this happens none can connect.
View 13 Replies
View Related
Sep 6, 2011
My linksys router reset itself. Yes it reset itself. It resets to default paramaters. I had to change the router parameters in the webpage with the wired connection to the router. That works fine, but after a day or say it comes back to default again. I am going crazy, I am sure nobody is pressing the little button on the router. Do I have virus or something or maybe the router is going bad. It's a WRT54G.
View 2 Replies
View Related
Mar 27, 2011
I was trying to set up an ad hoc network and toyed around with some of the wireless network settings. The network I was trying to set up didn't quite work out so I tried to set it back to how they were but forgot how they were. Is there a way to delete the Wireless Network Connection and let it create a new one or is there a "standard" setting for this to strictly find a wireless network and connect to it?
View 14 Replies
View Related
