Wireless :: No Internet Connection After Reset Router?
Jan 29, 2011
normally insert the D-link CD in my computer and then follow the steps. this time in the step that all connectivity was being checked the message appeared that one of the cables (ethernet or the other one) is not connected whereas I am quite sure that they are properly connected and nothing at least as far as I know is wrong.after several times, I could connect to the wirelss connection but actually there was no internetwhen I also tried with cable directly from wall jack to my computer it was also the same case.
I've just managed to reset the WRT 300N to default settings and have setup the internet connection etc and home network ... BUT no matter how I've fiddled with the wireless settings I cannot get any of the laptops or mobile phones to connect wireless to the network.The Windows software on the laptops 'finds' the router OK but for some reason the router seems unwilling to supply an IP address.I've checked ALL of the settings that I can think of, and all are correct ... well, all are exactly the same as my old router which worked perfectly.
since last nite my router E1200 has been having speed up and down problems.first it goes to 150mb/s then back down to 1 for a few minutes, usualy its stuck at 72mb/s which is a far cry from its rated 300mbps but qi'd rahter have that than 1-2mbps.i'd be happy with 150mbps but that only lasts 5mins then goes down to 1-2mbps and i have to reset my connection.
I have a Linksys WRT54GS (v5) router. I noticed that my firmware was outdated and tried to upgrade it tonight. During the upgrade progress, the browser reset the connection and now cannot access my router configuration pages.I did a hard reset. Then I did the 30-30-30 reset.
The reset worked but no matter what I do, I cannot navigate to any readable page within the router. I get the log in box and successfully log into the router. However, the configuration page(s) are all jumbled and devoid of useful information. It almost looks like a web page that needs flash to be enabled. Lots of colors and boxes but no text or links to other configuration pages
I know it's an old router but it has served me well. I would love to reinstall the old firmware (or new!) and copy my saved configuration file back to the router.Is there a way to access the configuration via a command line interface?
Every night I turn everything off via power strip, including the router. Before I turn off the router, my roku connection is good.In the morning, the roku will work for about 20 minutes, then disconnects, and then I'm unable to find the router.I'll then need to reset my router's settings (I have the WRT54GS), and then uplug, and replug the router.It's important that I unplug the router every night.Is there a way to configure the settings so I don't have to reconfigure the settings every morning?
I was in the Wireless tab>Basic Wireless Settings and then I clicked the "Reset Security" button. I don't know what that did but I've been completely shut out of my connection ever since and I don't know how to fix it. I tried doing the install sequence of the router just now (Clone MAC address, then release and renew DHCP, power cycle modem, router, and PC) but it still didn't work.
i was having issues with one of my devices after a power outage. all my other devices worked (laptops, xbox, iphones, etc)i thought doing a reset on the router would get the odd device working again but all it did was mess up my internet. i don't have the key or cd any longer from when i set it up.
Using it w/ my HP laptop since July, just got Mac book and was trying to use w/ that addition laptop but could not find router password, also 192.168.11 would not let me access w/ password: admin, so I reset the router and renamed it. NOW my HP laptop shows my router connected, BUT will not access internet.
I cant remember my password and i lost my cd installer. someone hacked my internet line< I want to change my password but cannot get through the router mainframe.How can I access my router?
I was trying to set up an ad hoc network and toyed around with some of the wireless network settings. The network I was trying to set up didn't quite work out so I tried to set it back to how they were but forgot how they were. Is there a way to delete the Wireless Network Connection and let it create a new one or is there a "standard" setting for this to strictly find a wireless network and connect to it?
Yesterday I had to move the computer desk to paint the wall behind it,which included unplugging the router and modem.There are four computers in the house,three on wireless, and after I hooked everything back up the pc in my room and the hardwired one reconnected to the router and internet just fine.My brother's pc and my laptop though can't seem to connect, they attempt to connect but just say they can't connect.
I work at the Staples Easy Tech center and the resident tech there told me to do an IP flush or some such thing, but my google fuu is weak and this "ipconfig /release" and "ipconfig /renew" refuse to do anything without a connection to the network.I proceeded to hardwire my laptop and even then it says no internet connection and doesn't recognize the network. I already power-cycled the router.Maybe power-cycle the modem?Reset mac addresses?
my laptop only connects to the internet when the router is off, then switched on. If the router is on when I turn my laptop on it won't connect, but it always connects when I do it the other way around. Other devices (like phones) connect to the internet via the same router flawlessly, it's just the laptop that, for some reason, needs to be on first.
I recently bought a new laptop (Asus U47VC) and i am having internet connection issues. When I am at my mother's place or at school, I have no problem connecting to the internet wirelessly. However, at my father's place, my internet stops working every couple hours and will be unable to connect to the network until i reset the router and modem. Once the reset is complete, I am good for another couple hours. All the other devices ( laptops, iphones, etc.) do not have this problem and the connection is never an issue. I have read that this could possibly be a problem regarding IP addresses but I do not quite understand how to fix this.
I have a router that needs to be reset to get the internet speed back to a usable speed. It is a fairly old router (D-LINK DSL 2730B) and it does get quite annoying. There is allot of devices connected, which may affect the speed, but I am sure it shouldn't change upon reboot. I literally reboot every hour or 2 during peek periods.
I'm having issues accessing facebook from my system, it worked untill a few days back where its not opening and gives a message "The connection to the website was reset". I have tried every trick in the book. I'm on Windows XP Pro.
1. I tried accessing the site from IE6 opera and mozilla still no luck.
2. I disabled my firewall and antivirus
3. Zonal Alarm and avira
4. I also uninstalled both and tried nothing worked.
5. Im able to ping the site and also did a tracert.I also flushed the dns and winsock.
I have a different problem, after i succesfully erased the spyware protection virus, i cant get in the internet anymore :( it always says "the connection was rest" on firefox and it wont load any site in IE either. what to do
We have a site to site VPN tunnel that consists off a Cisco 877 at a remote site and a Cisco ASA5510 at the Head Office.
Remote Site 192.168.100.0/24 > Head Office 192.168.0.0/24
telnet 192.168.0.36 25 works telnet 192.168.0.34 443 works telnet 192.168.0.202 21050 fails ping 192.168.0.202 works
The VPN tunnel is working in No NAT mode and allows IP any from each subnet. AD replication works fine across the VPN tunnel and so does telnet from the remote subnet to an exchange/web server at the Head Office.
The device on 192.168.0.202 is listening on the required port as we can telnet to it locally. The device does have a different gateway, but a route statement is in place to use 192.168.0.2 as it's default gateway for 192.168.100.0/24 traffic.
What doesn’t work is a connection to the phone system, we get the following in the logs:
6 Jun 09 2011 22:20:20 302013 192.168.100.1 60759 192.168.0.202 21050 Built inbound TCP connection 5799085 for outside:192.168.100.1/60759 (192.168.100.1/60759) to inside:192.168.0.202/21050
I receive the following error message:The connection was reset The connection to the server was reset while the page was loading The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.I am unable to connect to Facebook on my home computer, but can visit any other site with no problems. I can access Facebook from my work computer. I am using Firefox on both. I only use wifi as I only have a laptop and my router is in my office. I can access Facebook on my phone with my wifi enabled. I have not tried a direct wired connection (will try that next and let you know what happens) as I don't use my office, because it's currently full of junk.
Clearing the cache and cookies Reinstalling Firefox Updating Firefox Changed Firefox proxy settings to "no proxy" Resetting my wireless router Checking the Hosts file for facebook entries (there are none)
And still no access. The only way I have been able to access Facebook is by turning the firewall off on my wireless router (Belkin Wireless G). I don't want to have to turn the firewall off just to go on facebook. I am the only person in the house who uses a computer and the internet. So settings have not been changed, because I am the only person with access to change them (password protected wireless network as well).
I just changed my internet provider from DSL to cable. When I hooked up the DIR-615 I had some difficulties. At first my computers would all connect to the router but there was no internet connection. I had to download the latest firmware and install it. After the install succeeded, everything seemed to be okay. However, I now occasionally get the message that the connection to the server was reset while the page was loading. Also, the little world symbol on the router constantly flashes at a rapid rate. Before the switch, neither of these two things happened. When I check the download speed it seems fine. The cable modem is an Arris and also handles my telephone service.
I just purchased a Vizio Dual-Band HD wireless internet router, completed the steps on the quick start guide and I can get internet connection using my desktop but I cannot get internet connection using my MacBook. I went to [url]... and in the top right corner, it says "Offline" on the router. How do I make it say "Online"?
my router has intermet but i cannot get a connection to my computerbut its not just my computer my bfs computer our PlayStation nothing can connect to it right now i tried going in network and settings and diagnosing it and i tried unplugging the motem amd all the wires nothing is working. Two of the lights on the motem are green one is orange the wirless is lighting up blue. This is not the first time either....it came back after a while last time but now its not.
My main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
Ok starting about an hour ago I seem to be having a problem accessing youtube as well as Facebook & now Microsoft?I have done some searching around and tried a few of the suggestions I found including; trying another browser (happens using both Mozilla and IE), clearing internet cache, unplugging my modem for a minute then plugging it back in, etc, and so far none of these have worked. I did get youtube to work once since then long enough to upload a 10 sec video but once it was uploaded and I tried editing the video details I once again found myself taken to the page that says The connection was reset.
I have been having this problem randomly on and off the last week or so. If I type facebook in any of my browsers it comes back with the connection has been reset. If I use hidemyass I can get onto facebook though. My partner is having the same problem. I haven't got a firewall blocking facebook and it works sometimes and other times it doesn't so I am unsure what the problem is.
Ever since setting up this router it has been giving me problems on my laptop, connected wirelessly. At random intervals, throughout the house, an error saying "Connection was reset" comes up in firefox when browsing the web. I've tried resetting the router twice, and updating my network adapter's(Intel 465AGN) drivers. Neither of these worked. No settings on the router were modified, other than enabling the Qos engine. Signal quality isn't the problem either as it is full at all times. On my other computers, three connected through wireless and one through wired, there have been no problems at all and they perform very well.
Just bought myself an ASA5505 to replace a PIX 501, and having transferred over most of the previous config I've managed to get the two IPSEC VPN tunnels working as before.
Unfortunately when I try and SSH to the ASA the connection just resets instantly even when the tunnel is up. It seems as if the ASA is actively refusing the connection, though the log doesn't state this. I had always presumed that traffic over an established IPSEC tunnel was implicitly trusted and not subject to usual access-list rules.
I am unable to SSH to the ASA from the 10.0.0.x range, but I can SSH to a machine on 10.27.0.4 (so I know the tunnel is up and working)
Config (minus irrelevant sensitive information) is attached for reference.
Also - though I'm not sure how relevant it is given the tunnels appear to work - when I enter the line "crypto map meepnet-map interface outside" in config mode the ASA reports "WARNING: The crypto map entry is incomplete!" even though I have supplied the access-list, peer and transform-set variables.
I'm expecting some problems with ACE. I've configured it to loadbalance between 4 nodes with SSL termination at ACE.
Everything was working fine up to the identification of a problem using firefox browser. With Chrome and IE works fine.
The user is trying to upload a file to one of the 4 nodes. When the costumer click at the send button, the Firefox shows the following message: Connection Reset.
This problem just happens when the user try to upload the file. Whe he's just surfing through the system, works fine.
------ Configuration ------
ACE-01-SJPR/eproc4# sh run Generating configuration.... logging enable
Ok, so I reset the router but i still can't login to the setup using the factory password (admin/admin) (blank/admin) (admin/blank). Now I have an unencrypted network and no access to the setup... I even tried using the setup CD but it doesn't recognize the router.
My EA6500 has been working fine for the last few months but a few days ago i upgraded to the latest firmware 1.1.28.147876 - this was done by an ethernet cable, not by wifi. However i've noticed the router reverts back to the previous fw 1.1.28.146856 when the router is rebooted or factory reset. I've repeated the fw upgrade process and also done a hard reset before upgrading the firmware but no avail. Normally after firmware is 'upgraded' the router reboots and i get the message "firmware successfully installed" but then on subsequent reboots the firmware reverts back. I'm using local router access but even using smartwifi gives the same issue. When upgrading fw, i've tried both options online & manual but again makes no difference.
Don't really fancy calling Linksys support and going through 4 hrs of basic trouble shooting. Or perhaps Cisco have introduced a new automatic firmware downgrade option in their routers?
My linksys router reset itself. Yes it reset itself. It resets to default paramaters. I had to change the router parameters in the webpage with the wired connection to the router. That works fine, but after a day or say it comes back to default again. I am going crazy, I am sure nobody is pressing the little button on the router. Do I have virus or something or maybe the router is going bad. It's a WRT54G.
I am wondering how to reset the password for my wireless router? I am finding it hard to set up a new pc each time because it seems the password is always wrong. I want to set it to something I will easily remember.
