D-Link DIR-615 :: Connection Reset Message After Changing ISP?
Jan 30, 2011
I just changed my internet provider from DSL to cable. When I hooked up the DIR-615 I had some difficulties. At first my computers would all connect to the router but there was no internet connection. I had to download the latest firmware and install it. After the install succeeded, everything seemed to be okay. However, I now occasionally get the message that the connection to the server was reset while the page was loading. Also, the little world symbol on the router constantly flashes at a rapid rate. Before the switch, neither of these two things happened. When I check the download speed it seems fine. The cable modem is an Arris and also handles my telephone service.
View 10 Replies
ADVERTISEMENT
Mar 5, 2012
I'm fine tuning some of our ASA logging config, and am having an issue with one particular syslog ID.The message is: syslog 106100: default-level informational (enabled)and the log settings are:
Syslog logging: enabled
Facility: 20
Timestamp logging: enabled
Standby logging: disabled
Debug-trace logging: disabled
[code]....
This ACE log entry is generated by explicit deny any any statements at the end of all the ACLs, e.g.access-list inside_access_in extended deny ip any any log interval 600 Based on the config, I would expect to see this being logged to the syslog server, but not to the local buffer, but am still seeing them locally in the buffer:
Feb 22 2012 10:58:20: %ASA-4-106100: access-list inside_access_in denied udp INSIDE/HOSTABC(52629) -> OUTSIDE/HOSTXXX(162) hit-cnt 5 300-second interval [0x3baecf1e, 0x0]
It also still shows these as level "warning", %ASA-4-106100, instead of the default %ASA-6-106100 I've tried removing and re-applying the config at different levels but it still reports in the buffer log as level "warning", %ASA-4-106100 This also doesnt affect every 106100 log that is generated. Most messages are generated at the correct level 6 severity but some seem to randomly log at level 4. There doesn't seem to be any pattern to this. The same access-list line can produce severity level 4 and 6 106100 messages.
View 2 Replies
View Related
Oct 30, 2011
Here's the current scenario:
[LAN] <---> ASA 5520 <---> Cisco 2911 <---> [Internet] <---> Server A
|
|
[DMZ]
Whenever I access a website running in "server A" (only HTTP traffic) everything works fine. The problem is that when I try to access a different service on the same server but listening on port 2000/tcp I get the TCP Reset-O message on the ASA and the workstation's browser says that "Internet Explorer cannot display the webpage".
A weird thing: if I access this service from a machine on the DMZ, it works fine. From the LAN (Inside) it does not work. The main difference is that from the LAN to OUTSIDE the ASA does NAT. From the DMZ to OUTSIDE it's just routed. I did another test from the LAN and the captured traffic is attached. I've been messing around with protocol inspects and firewall + NAT rules on the ASA but no luck at all.
View 5 Replies
View Related
May 11, 2010
Ever since setting up this router it has been giving me problems on my laptop, connected wirelessly. At random intervals, throughout the house, an error saying "Connection was reset" comes up in firefox when browsing the web. I've tried resetting the router twice, and updating my network adapter's(Intel 465AGN) drivers. Neither of these worked. No settings on the router were modified, other than enabling the Qos engine. Signal quality isn't the problem either as it is full at all times. On my other computers, three connected through wireless and one through wired, there have been no problems at all and they perform very well.
View 2 Replies
View Related
Jan 29, 2011
How to change the security key. How does one go bout that? Did not see that within the manual for some strange reason.
View 1 Replies
View Related
Feb 27, 2012
We are trying to change our already wireless router to a new wireless router. Changing from a lynksis wrt54g to a d-link DIR-815.We tried using the quick router setup wizard they provided but it wasn`t able to connect to the internet to continue, then we tried manual setup (going on the web-based connection thing) since the wizard stopped working and we tried a manual setup.
View 3 Replies
View Related
Feb 23, 2013
[CODE]My current problem is the internet just isnt working right. It is slow, choppy at times or doesnt load all items on a page. If it doesn load a page sometimes I click on the stop X, followed by refresh and the page pops right upSometimes if I dont get a complete page a refresh will fix it. It is just a pain to work with.There is an Network Connection icon in the right corner of the task bar. It is two small blue screens. It keeps changing from a red x, an exclamation point, and three blue balls or nothing. If I rest on the icon it flashes the status of the network:[CODE]
View 12 Replies
View Related
May 2, 2012
I was told that i need to disconnect from my wireless and hard-wire the connection directly from my modem. My wireless connection is downstairs in the basement. Do i need to call a professional to do this or is this something i can do from home?
View 1 Replies
View Related
Dec 10, 2011
I have a new SMART T.V. I have no trouble hooking up wirelessly to my N300 router, I can get on the internet without any problem. Then I added a wireless speaker system, now the T.V. won't hook up to the router any more. My question is, how do I change channels on the N300 DIR 615 router so that I can get away from the interference caused by the wireless speaker system?
View 3 Replies
View Related
Apr 8, 2012
I need to change my DCS-942L camera settings remotely when I am not connected to my home wireless network. When I am at home, I just type in the local IP address of the camera (192.168.0.100) into my browser to access the firmware. How can I do the same when I am away from home and obviously not connected to the local WiFi?
View 1 Replies
View Related
Apr 29, 2011
I recently set up my DIR-615 on my wireless netbook. Everything worked fine and I could get online. But then when I changed the password on the router, it bumped me off and now says Internet isn't available. My phone can connect to Internet but not my netbook anymore. When my netbook tries to troubleshoot it keeps saying "problems with router and adapter."
View 1 Replies
View Related
Sep 29, 2011
I have a Linksys e2000 wireless router, my laptop connects fine, but as i keep hovering my mouse over the wireless icon in my system tray, it keeps changing Mbps from 130 at its highest going down into double digit Mbps, then back up to 130. Why wouldn't it stay connected at 130 all the time?Someone said to try lowering the beacon interval, fragmentation threshold, RTS threshold, and mtu size, but will doing that decrease the speed of my connection to the router?
View 5 Replies
View Related
Jul 30, 2012
Our ISP provider made our internet connection a dial up. Last time it automatically connects to internet without putting those username and password. So after they changed it only our server pc have internet. Others don't have. The technician from the isp provider keep telling that the switch(but he keeps telling us its a router dunno why) need to be configure but switches dont need to be configure right?
View 3 Replies
View Related
Sep 6, 2011
I am a newbie regarding mobile IP.the meaning of the phrase "changing the link-layer point of attachment to the Internet, yet without changing its IP address".
View 1 Replies
View Related
Jul 17, 2011
I have a DIR-825 router connected to my cable modem. The 2.4ghz constantly goes down but not the 5.0ghz. Our wireless devices will see the connection but we are unable to connect.We only have one device that uses the 5.0 and multiple devices that use the 2.4 and none of them can connect.I am currently running firmware 2.02. I also notice that the time changes and I have to reset the time/date.I have tried rebooting the device, resetting the router, changing the network key, updated the time/date, renewed the DHCP...I don't know why it keeps going down, why the time/date keeps changing, and why I cannot get the 2.4 working.
View 13 Replies
View Related
Mar 22, 2012
I have a new router. this seems to be a very simple problem relating to the most basic configuration options.
Hardware Version: A1 Firmware Version : 1.01NA
go to SETUP -> "NETWORK SETTINGS"
change "Router IP Address" to 192.168.73.1
change "DHCP IP Address Range" to: 192.168.73.10 : 192.168.73.200
Save Changes Wait for reboot. change my client system's local IP address... so that I can reconnect. direct web browser to http://192.168.73.1/
seen: login page has a select-box for a userid, but no text inside. there is no prompt to ask me to login. I press enter (or whatever... I login). every form interface on all web pages looked at have no labels on text boxes.
I did a view source... and used web-dev tools to look at the page. it looks like the apparent js function, show_words(), is not defined.
change ip address and dhcp address range back to default save changes. wait for reboot. reverse changes to local system things are back to normal. login page has useful text. after logging in, there is something to read.
looking at source again. I see, now, that the js function "show_words" is defined in a file called public.js.
View 5 Replies
View Related
May 16, 2010
Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password
newpassword
confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
View 4 Replies
View Related
Jul 12, 2011
Does 6rd working on the DIR-601?
For example if I enter the Comcast 6rd parameters:
6rd IPv6 prefix 2001:55c:: /32 6rd border relay IP address 69.252.80.66
I then click on "Save Settings". Now I get a pop up message that says "Invalid IP address" I'm running firmware 1.02NA
View 7 Replies
View Related
Oct 5, 2012
There are a lot articles on the web about changing a wireless connection's password or security key. Pretty simple. But my computer does not remember the change and when trying to reconnect it still has old password and fails.
View 1 Replies
View Related
Jun 15, 2011
I recently bought a tenda w548d Version 2.0 Adsl2+ Modem router. it worked fine with its default settings and wired connection was ok when i chose DSL uplink while installing its driver from CD. But it couldn't connect wireless. There were strong signals but connected computer couldn't get access to the internet. so i tried using ethernet uplink instead of DSL uplink while reinstalling the software Since then the light of ADSL never lights, even it never blinks. now the software on the cd can connect to the router. i cannot access its settings using IP address in browser, the page wouldn't load. I am so worried. Can i revert the setting back to dsl uplink?I can connect to the internet very smoothly using my old router so you can't blame my phone line or lan wire. I have tried reset the new router many times but still the ADSL light never lights up. And the ADSL light is ok because when i turn the router on, it lights with all the others.
View 2 Replies
View Related
Jan 23, 2013
When I change a setup setting and click save settings, most of the time it gets stuck on the "saving..." notification window and eventually I get a "Internet Explorer cannot display the web page" notification. However I have found that if I repeatedly try it eventually it will accept the change. This never happens using the wizards only making manual changes. I am running the camera with a Wi-Fi connection. I am not sure this is a router or camera firmware bug (running V1.12)
View 4 Replies
View Related
Sep 1, 2011
Smart Link 56K Voice modem is installed. When I send fax message it rings at the other end but the message does not get transmitted. I get a message "No answer" similarly when for incoming fax there is ring but message is not transmitted.
View 1 Replies
View Related
Jun 11, 2011
How i can change my ip address without changing my internet connection??
View 3 Replies
View Related
Dec 31, 2008
I purchased a WRT110 wireless router several weeks ago. Used it with my WPC55AG with no problems at all. I liked the wireless-N, so I decided to upgrade to a wireless-N notebook card and purchased a WPC100. I can always connect to the router with 100% signal strength. However, when trying to access the Internet, sometimes I can connect to websites, but I regularly get an error message that Internet Explorer cannot connect to the internet, even though the signal strength is still 100%.
Tried going back to my WPC55AG and do not get any connection error messages. Tried connecting to my router with my PSP and do not get any connection error messages. Connected to another wireless router that didn't have WPA or WEP using my WPC100 and didn't get any connection error messages..
View 5 Replies
View Related
May 24, 2012
I have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
View 8 Replies
View Related
Feb 17, 2013
-Region : Poland
-Model : TD-W8951ND
-Hardware Version : V5
-Firmware Version : 5.0.0 Build 120522 Rel.23978
-ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
View 2 Replies
View Related
Mar 15, 2011
DIR-655 RevA4 - upgraded to 1.35NA, which is shown on http://192.168.0.1/
When I try to re-log in as Admin, I get a message of invalid password. I have unplugged to reset, but still cannot get back in.
View 3 Replies
View Related
Aug 27, 2012
I recently changed my graphics card (geforce 9100 to radeon hd 7750) because i wanted to enjoy some simple gaming and my previous graphics card (geforce 9100) wasnt capable of doing so. (This is my pc : HP Pavilion p6100 Desktop PC series*-* HP Pavilion p6130y Desktop PC Product Specifications - c01748306 - HP Business Support Center ). Before changing the card i uninstalled all nvidia related drivers (both in control panel and device manager) because i heard thats what youre supposed to do.
I successfully changed my graphics card (i think...) i can run all the games that i couldnt run before but.. I am having trouble connecting to the internet after changing the card. it seems like my computer isnt recognizing the inernet network. i know the network is fine because im writing this w/ my itouch which is connected to the network wifi. When i right click the red X icon w/ two computers and click "connect to a network" , it says "windows cannot find any networks" and i have no network options to choose from. Is it because i uninstalled drivers related to the network connection..?
View 2 Replies
View Related
Sep 17, 2011
i got an error while connecting to my PIX (515e) via ssh connection there is an error message appears (The server has disconnected with error, server message reads: Internal Error) and at the console session at the time time, the following message appears also (process_create: out of memory)
View 1 Replies
View Related
May 7, 2011
My roommate has just gotten a second hand laptop and he's trying to connect it to the Wireless network so that he can browse the internet from his room.However, although all the settings are correct, attempting to connect to the network loops.It comes up showing the Wireless Networks available, I select the network and click connect, it then asks for the encryption key. I enter the key and hit connect again, it comes up with the 'Connecting' pop-up and then loops back to the Available Networks screen again.There are no error messages, it just goes back to the starting screen and it hasnt connected.The Laptop in question is a Lenovo T60 with a Intel PRO/Wireless 3945ABG card.The router is a TP-Link TD-W8960N.
View 5 Replies
View Related
Apr 15, 2013
I have a Dell Studio 17 with a wireless internet problem. The wireless internet just stopped working with a message error "modem has been removed". When I try to plug in to a hard wire connection I can connect, but the 3G network want allow me to go on online without the above error messageand a message asking me to select the service you want to connect too, yet it still tells me that I am connected.
View 1 Replies
View Related
Apr 5, 2013
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Virgin Media Limited
when I forward ports I get the following error message:
Things to note:I have the web GUI running on 8080, because I run a file-server on port 80.
I am using a Virgin media branded router in 'modem mode', this would not cause issues.
I did not do anything to change anything, I went to add an additional port to forward and it didn't work.
I am on a Dynamic IP
After it stopped forwarding, I upgraded firmware to: 3.13.26 Build 130129 Rel.59449n.
View 11 Replies
View Related
Jan 22, 2013
my cable company tells me my router is not refreshing ?? even after i disconnect - reconnect ..the power is the button on top with the circling arrows for refreshing it .. i do have a static IP if that makes a difference .
View 8 Replies
View Related
