-Region : Poland
-Model : TD-W8951ND
-Hardware Version : V5
-Firmware Version : 5.0.0 Build 120522 Rel.23978
-ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version :
ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : 5.0.0
ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
Region : Kazakstan
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120207 Rel.10587
ISP : Megalne
I have two comps in LAN (Ethernet) - one (Comp1) in WinXP, another (Comp2) in Win7. IPs for both comps are assigned by DHCP. Internet is available for both Comps and for assigned wireless units. So the router is configured almost well. But I lost my home net: can't see or ping anything in LAN. Setting of static IPs (192.168.1.4 and 192.168.1.6 are permitted)
i have a PPPOE type of connection for my modem and just now my router is blinking both lights Orange and blue at the same time....but the internet is still connected..
View 14 Replies View RelatedModel : TD-W8951ND
Hardware Version : V3
Firmware Version :
ISP : BSNL DATAONE
my tablet show wifi status connected ... signal quality... but cant access internet ...
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120703 Rel.29030
ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : Latest
ISP :
In trying to make sure it was NOT wide open to the internet (amongst many other problems of setting it up, which I ,may address later if I can actually connect to the thing ever again) I told it to only accept connections from a range of address inside the LAN. Now it wont accept anything except telnet from the LAN.Short of wiping out 6 hours of trial and error configuration and resetting it, are there any other options I can exercise via the telnet interface?
Region : Malaysia
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : V5
ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
My router TD-W8951ND remembers only a dozen of latest logs. Previous, older logs disappears. Why? Is there any way to force router to keep logs from, for example, the last 12 or 24 hours?It is important to me because i have some problems on my adsl line and i want to know what happens with connection while I am not in home or when I sleep.If it will be necessary I am able to log onto my router using Telnet, just give me required commands to fix this problem with logs.
Region : India
Model : TD-W8951ND
Hardware Version : V5
Firmware Version :
4 lan ports problem in my modem. Able to get internet through wifi but unable through lan ports.checked in 2 pcs and 1 laptop
Region : India
Model : TD-W8951ND
Hardware Version : V4
ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
On my router TD-W8951ND constantly there are the same type errors, while using computer conected to the router:
Code:
2/16/2013 17:24:8> netMakeChannDial: err=-3000 rn_p=80544b08
2/16/2013 17:24:13> Last errorlog repeat 2 Times
[Code].....
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : TD-W8951ND_v5_120522
ISP : N/A
The wireless adapter settings page has an entry for 'PIN' and 'PBC' for WPS.Selecting either always results in the client station requesting the routers pin, indicating that the pushbutton selection is not working properly.The router was doing this with the version of hardware that it was shipped with. i have downgraded to 120522 and the router is behaving exactly the same.Has anyone successfully configured the router for pushbutton connection? do not suggest that we use the pin setting as we have a requirement for dumb devices to connect to wireless and they only support pushbutton connection.
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 22.05.2012
ISP :
I have a TD-W8951ND v5 on the latest firmware.
I recently broke my broadband data cap which surprised me as I had not been using the internet much.
I only have tablet which I switched off having first checked the router to make sure there were no other wireless connections and adding MAC address filtering to be sure no one else was stealing my bandwidth. With just my router connected to the ISP, my ISP has recorded 170MB of downloaded data in 3.5 hours. Switching off the router stops the traffic being recorded (as you would expect), but when switched back on the large data transfers start up again.
I have plugged in an older router (not wireless) and no traffic is generated, so it seems to be the TP-Link router rather than my ISP or ADSL circuit that is at fault.
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version : 6.0.0 Build 120213 Rel.30335
ISP : ETAPA
I am writing in from Cuenca, Ecuador. I have a TD-W8901G Wireless ADSL2+ Modem Router. I have accessed the interface using the default ip address:192.168.1.1.When I select Interface Setup from the menu, it only shows Internet and LAN as the only 2 options. Wireless is no longer there. It just disappeared! The LED indicator light for WLAN is also "OFF." When you try the Quick Start wizard guide, it cannot complete the setup because there is an IP address error.
I have changed the firmware 2x since, trying to remedy this, I have also tried factory resets at least 3x. Nothing has worked up to this point.
Region : France
Model : TD-W8151N
Hardware Version : V3
Firmware Version : latest
ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
Region : Sweden
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0_1.1_up(120926)
ISP : HessleholmNetwork
My TD-W8968 has begun to freeze up. It had been running for about two hours before this happened. It's a "slow" process that starts with the web interface being unavailable, i'm unable to connect to the modems web interface.And at about the same time it becomes impossible to connect new devices to the wireless network. Right about this point i did a speed test over the modem and performance was abysmal.It was so slow that my web browser believed that it was offline! But i was able to re run the internet speed test once more before it totaly locked up! At this point it was impossible to use the TD-W8968.
This was the,, i don't know,, perhaps the fifth time it happened in a row. It has been running perfect for two months before it began acting up like this.I have done a reset of the modem, didn't solve the problem.I have also done a reflash of the firmware, i've had the latest firmware since i bought the TD-W8968. But the reflash didn't solve it
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
I have a new router. this seems to be a very simple problem relating to the most basic configuration options.
Hardware Version: A1 Firmware Version : 1.01NA
go to SETUP -> "NETWORK SETTINGS"
change "Router IP Address" to 192.168.73.1
change "DHCP IP Address Range" to: 192.168.73.10 : 192.168.73.200
Save Changes Wait for reboot. change my client system's local IP address... so that I can reconnect. direct web browser to http://192.168.73.1/
seen: login page has a select-box for a userid, but no text inside. there is no prompt to ask me to login. I press enter (or whatever... I login). every form interface on all web pages looked at have no labels on text boxes.
I did a view source... and used web-dev tools to look at the page. it looks like the apparent js function, show_words(), is not defined.
change ip address and dhcp address range back to default save changes. wait for reboot. reverse changes to local system things are back to normal. login page has useful text. after logging in, there is something to read.
looking at source again. I see, now, that the js function "show_words" is defined in a file called public.js.
I upgraded then downgraded from 2.00 to 2.03 back down to 2.00, and whenever I'm doing about 600kB/s+ it resets itself. Drops connection drops wireless, wired, and the globe internet icon goes Lambert/orange. I've reset the router to default and it still does that. What could be the cause?
I've done a lot of changing around, disabling unicast, changing from WPA Auto to WPA2, etc etc, I just changed the router to Netgear WGR614 v7 and it works perfectly fine now.
when I connect my DIR-655 to the Motorola SB6141 cable modem I notice that the link speed LED on the cable modem never glows blue indicating a gigabit connection, it only glows amber indicating a lower negotiated speed. I am using a Cat6 cable between the two devices and have also tried a Cat5e cable.
When I try and force the WAN port speed to 1000Mpbs in the router interface the cable modem link speed will not light at all with no connectivity. Only resetting to Auto WAN port speed restores functionality albeit at the lower negotiated speed setting.
I'm running the DIR-655 rev B1 at 2.03NA firmware level.
I did connect the modem directly to my PC that uses an Intel Gigabit ethernet card and still had the lower connection indication (Amber) so it seems that the modem might be faulty.
i have TP link router model no TD W8951ND.. i can access internet but wifi disconnects in every 5 mins.. i have to connect again but as soon as i got connection after 5 or 10 min it disconnects again..
View 1 Replies View RelatedI have a TP-LINK TD W8951ND wireless Modem+Router which contains one RJ11 (phone line) port and four RJ45 (Ethernet) ports along with wireless N support.
Now for some reason, my TP-LINK modem doesn't work with my ISP, whereas the modem provided by my ISP works. If I wish I could get the basic modem provided by my ISP which contains one RJ11 port and one Ethernet port.
So can I link both the modems? I mean will this configuration work: Connect telephone cable to basic modem provided by ISP. And then connect the Ethernet port of basic modem to the Ethernet port of TP-link modem. And then connect remaining Ethernet ports to PC and laptop and simultaneously use WIFI.
Will it work or should I have to replace my TP-Link Modem+Router?
I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
Yesterday, my DIR-600 are working fine, but the led of the power and the WAN are orange, now, only the power led is orange, i can't enter in 192.168.0.1
View 1 Replies View RelatedI have a D-LINK 601 router which has been working fine. I was told by a friend that it is not password protected. I think that I have set it up now with an adm password. The router and the DSL modem is still connected as before, but the Internet LED blinks orange.
View 1 Replies View RelatedThe D-link dir-615 is not working.The modem is working perfect, because its the internet that im using right now (its connected directly to my laptop, so i know its the router for sure) But i want to make the internet on my modem wireless, but the D-link router has the orange globe light turned on (as im typing it still has the light on) and i just dont know whats wrong with it. I have already tried reseting it like 2 times, and it still doesn't work. When i connect my router, all it does is acquire the network address, and it just stays there, so no ip address will be detected... I might just buy a lynksys router, d-link sucks. This router was bought years ago by the way. It hasn't been used since like now.
It isnt the computer, i tried disabling the firewall, and reconnecting, but it just stays in 'renewing ip address' (the same things happen with all of the other computers that try to connect to it in my home) I click on the wireless icon and then on 'support' and next to IP Address it says "Invalid Ip Address"... The globe still remains orange on the router..
Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
The internet connection light is blue, i am assuming this means the device thinks that it is connected. However wired or wireless I can't hit any web pages. When I use the internal tools neither can the device ping any address.
I am using:
Firmware 2.00NA
DSL modem ATT-Yahoo-SBC (Speedstream 4100 using DHCP)
I am planning to upgrade the firmware to 2.01NA and give that a shot.
I reseted my router because I couldn't go in the login so now eveything is green except the earth looking thing next.the power it is orange Cause I really need my internet
View 1 Replies View Related
