i have TP link router model no TD W8951ND.. i can access internet but wifi disconnects in every 5 mins.. i have to connect again but as soon as i got connection after 5 or 10 min it disconnects again..
View 1 Replies
why does my internet disconnect every 10 minutes with a hard wire modem,an then start working for 12 to 24 hrs.
View 1 Replies View RelatedI have a D-Link 655 and I want to restrict my guest zone more.
1. Is there a way I can make devices disconnect if they're not active after 30 mins?
2. Is there a way that I can restrict my Guest Zone to ONLY use b and g NOT n?
I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
i'm using 2960 cisco switch and every department has a switch same model, i have noticed that every 10 to 15 minutes my network is disconnected for atleast 10 seconds and all client conneted to the server was disconnected also.
View 26 Replies View RelatedI have a TP-LINK TD W8951ND wireless Modem+Router which contains one RJ11 (phone line) port and four RJ45 (Ethernet) ports along with wireless N support.
Now for some reason, my TP-LINK modem doesn't work with my ISP, whereas the modem provided by my ISP works. If I wish I could get the basic modem provided by my ISP which contains one RJ11 port and one Ethernet port.
So can I link both the modems? I mean will this configuration work: Connect telephone cable to basic modem provided by ISP. And then connect the Ethernet port of basic modem to the Ethernet port of TP-link modem. And then connect remaining Ethernet ports to PC and laptop and simultaneously use WIFI.
Will it work or should I have to replace my TP-Link Modem+Router?
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version :
ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : 5.0.0
ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
Region : Kazakstan
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120207 Rel.10587
ISP : Megalne
I have two comps in LAN (Ethernet) - one (Comp1) in WinXP, another (Comp2) in Win7. IPs for both comps are assigned by DHCP. Internet is available for both Comps and for assigned wireless units. So the router is configured almost well. But I lost my home net: can't see or ping anything in LAN. Setting of static IPs (192.168.1.4 and 192.168.1.6 are permitted)
I have not yet hooked up my router, N150. What I would like that after I hook the router up and then deside I don't want to use it. How do I disconnect it and go back to using my DSL modem and being connected to the internet?
View 3 Replies View RelatedModel : TD-W8951ND
Hardware Version : V3
Firmware Version :
ISP : BSNL DATAONE
my tablet show wifi status connected ... signal quality... but cant access internet ...
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120703 Rel.29030
ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : Latest
ISP :
In trying to make sure it was NOT wide open to the internet (amongst many other problems of setting it up, which I ,may address later if I can actually connect to the thing ever again) I told it to only accept connections from a range of address inside the LAN. Now it wont accept anything except telnet from the LAN.Short of wiping out 6 hours of trial and error configuration and resetting it, are there any other options I can exercise via the telnet interface?
Region : Malaysia
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : V5
ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
My router TD-W8951ND remembers only a dozen of latest logs. Previous, older logs disappears. Why? Is there any way to force router to keep logs from, for example, the last 12 or 24 hours?It is important to me because i have some problems on my adsl line and i want to know what happens with connection while I am not in home or when I sleep.If it will be necessary I am able to log onto my router using Telnet, just give me required commands to fix this problem with logs.
Region : India
Model : TD-W8951ND
Hardware Version : V5
Firmware Version :
4 lan ports problem in my modem. Able to get internet through wifi but unable through lan ports.checked in 2 pcs and 1 laptop
Region : India
Model : TD-W8951ND
Hardware Version : V4
ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
Region : UnitedStates
Model : TL-MR3020
I'm using a 3020 to bridge 3/4G to the ethernet port on my computer. Things work fine until I also join wireless hosts (like an iPhone or iPad). The routing of traffic to both the ethernet and wireless hosts seems to cause the 3/4G router to lose the signal and disconnect all hosts. I'm using a Verizon LG USB wifi device that is on the compatible list of 3/4G devices. I'm using the latest version of the firmware on the 3020 (I believe the date is Sep 2012).
-Region : Poland
-Model : TD-W8951ND
-Hardware Version : V5
-Firmware Version : 5.0.0 Build 120522 Rel.23978
-ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
On my router TD-W8951ND constantly there are the same type errors, while using computer conected to the router:
Code:
2/16/2013 17:24:8> netMakeChannDial: err=-3000 rn_p=80544b08
2/16/2013 17:24:13> Last errorlog repeat 2 Times
[Code].....
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : TD-W8951ND_v5_120522
ISP : N/A
The wireless adapter settings page has an entry for 'PIN' and 'PBC' for WPS.Selecting either always results in the client station requesting the routers pin, indicating that the pushbutton selection is not working properly.The router was doing this with the version of hardware that it was shipped with. i have downgraded to 120522 and the router is behaving exactly the same.Has anyone successfully configured the router for pushbutton connection? do not suggest that we use the pin setting as we have a requirement for dumb devices to connect to wireless and they only support pushbutton connection.
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 22.05.2012
ISP :
I have a TD-W8951ND v5 on the latest firmware.
I recently broke my broadband data cap which surprised me as I had not been using the internet much.
I only have tablet which I switched off having first checked the router to make sure there were no other wireless connections and adding MAC address filtering to be sure no one else was stealing my bandwidth. With just my router connected to the ISP, my ISP has recorded 170MB of downloaded data in 3.5 hours. Switching off the router stops the traffic being recorded (as you would expect), but when switched back on the large data transfers start up again.
I have plugged in an older router (not wireless) and no traffic is generated, so it seems to be the TP-Link router rather than my ISP or ADSL circuit that is at fault.
My D-link router won't give me a break. Every 10 or 20 minutes it resets, severing the internet connection. This is extremely annoying, especially when I'm playing online games or downloading something. Simply put, the three lights suddenly turn off, then they start turning on again one after the other. I don't want any of the automated answering machines with their usual 'help', like "download update", "contact your ISP","disable your firewall".
View 2 Replies View Relatedrouter started disconnecting clients every few minutes
View 2 Replies View RelatedI have a dlink cable modem and dlink dir-655 router. When the router is first turned on or a setting is changed any/all of the computers here can connect to the Ultima Online game server for login but within a few minutes most will not be able to. Its as if they are being refused a connection to login.owo.com (I think that is where they connect to). 1 maybe 2 computers can still connect but its fickle and can't know which 1 or 2 it will be or for how long.any computers already connected to a game server are fine its just the ones trying to login after the router has been running for a few minutes. My first assumption 2 days ago when this happened with my dlink gaming router was that the router developed a problem but now with a new router its still happening. The problem started when I re-enabled the wireless on my gaming router and when I noticed the problem I re-disabled the wireless but the problem persists. A new modem (the DIR-655) did not work...
View 10 Replies View RelatedI have a Sky [Sagem] F@ST2504N Wireless Router and Sky is my ISP. I have been using powerline adapters to extend my network into a room upstairs that is a WIFI deadzone. I would like to use a router to turn this into a wireless signal in the upstairs room. i.e. Primary (SKY) Router -> power line in -> powerline out (Upstairs in deadzone) -> Secondary (TP-Link) Router..I have got a TP-Link 150mbps wireless N ADSL2+ Modem Router (Model No.: TD-W8951ND) .I am plugging this in and configuring it from factory settings via the web setup. How to configure the new router?
View 4 Replies View RelatedEvery few hours, the WAN just shuts off. If you were connected to it when this happens, you cannot reconnect until you have reset the router; you can't even find the SSID. If you were not connected when this happens, you can connect just fine. This happens with all devices in the house, my laptop, my DAP-1522, my cell phone, and my brother's Mac (SMH, sometimes I think we aren't related...). I am running version 2.00NA on B1 firmware.
View 3 Replies View Relatedwhen i playing Online games it suddenly disconnect from the game while the other customer is just browsing and nothing happen to them... i try all the online game and same thing happens...
View 14 Replies View RelatedIf you are using DAP-1522 A1 and set to 5GHz 802.11 n bridge mode but disconnect randomly. Don't bother to do any troubleshooting because DAP-1522 A1 only support 802.11 draft n and incompatible with 802.11 n. If unit still under warranty then call D-Link and request unit replacement and ask for hardware reversion B1.
A1 - Ralink RT2880+RT2850 chips
[URL]
B1 - Ralink RT3662 chip
[URL]
I buy this model is QOS, I just read a lot of DIR-655 streamengine article, it's hardware-base QOS router, can operate under heavy p2p application, it's why I am here.The wireless Client is ACER AS1810TZ laptop, the wireless card is Intel wifi link 1000, I have already disable power saving option. AS1810TZ worked fine with my old 802.11G router linksys WRT54GS and Buffalo WRH-HP-54G.The dir 655 seems fine when I just surfing web and download some files with IE, but when I check the statistics, I see a lot of wireless error and tx packet/ rx packet dropped, the percent I calculate is about 0.5%, I am wondering if it's normal phenomenal?When I download several bit torrent files With XUNLEI simultaneously, total 6 files, after 3 minutes, lot of session be created, the router slow down the download and finally crashed, wan be reset and wireless connection lost. router can recover after 1 minutes and try to continue the BT download again, but failed again. [code]
View 14 Replies View RelatedRegion : UnitedStates
Model : TD-W8968
Hardware Version : V4
Firmware Version : 1.1.1 Build 120912 Rel.67406
ISP : centurylink
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 1.1.1 Build 120912 Rel.67406
ISP : centurylink
First a bit of background. At the end of December, my centurylink modem finally had enough problems with disconnects(was 6 or 7 years old), and Centurylink sent out a new router/modem. The new modem/router, a Zyxel, worked great, and all was good in my house hold. Then I got the bill and found out that unlike the previous modem they had sent me, this one I was paying a lease payment for. At which point I returned the Zyxel which gave us the best service we'd ever had, and bought this TD-W8960N. The reviews were glowing, setup was easy, but we started rather quickly to have disconnects. A call was made to Centurylink and they confirmed service was working, and since the modem/router was not theirs, referred us back to you. I called and after considerable time on the phone, all I was basically told to do was a hard reset to the modem. When the unit finished booting back up, internet was restored. Of course it was restored everytime we reset it for a while. At that point I was told that since the unit was working, that there was nothing left to be done. Since that time, it has disconnected us from time to time, and then in the last 2 days, sometimes it won't stay connected for more than a couple of minutes. My wife is very unhappy-she is a gamer, and a disconnecting internet is very very bad for an online gamer.
It seems that the further it gets away from a hard reset,the more it disconnects. After 6 soft resets (unplugging) today, I had to do another hard reset to get back on to register here and post this message. Is this a known problem for this unit? Is there a fix for this unit? Or, do I just need to return it to Newegg and try another manufacturer?
Again, the "leased" Zyxel gave us no problems for the month or so that we used it.
Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : starhub
1) Always auto disconnect (limited access),
2) My smart phone Motorola MB860 (android 4.0.4) Can connect but can access internet.
3)Always connect to 2.4GHz ,never see connect to 5GHz.
4)Wireless connection 15-20 Max Mbps Only ,LAN can up to 50 Mbps .
