Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120703 Rel.29030
ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version :
ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : 5.0.0
ISP : Beam Telecom
I recently bought this device in hurry . My ISP has directly connected RJ45 cable to my laptop .So i need to use this device for sharing internet to my wireless devices .IS it possible to convert Rj45 to Rj11 if so let me know the process .I have seen interenet about converting lan port to wan for TD-W8960 device . but GUI administration is quite different for my device .
Region : Kazakstan
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120207 Rel.10587
ISP : Megalne
I have two comps in LAN (Ethernet) - one (Comp1) in WinXP, another (Comp2) in Win7. IPs for both comps are assigned by DHCP. Internet is available for both Comps and for assigned wireless units. So the router is configured almost well. But I lost my home net: can't see or ping anything in LAN. Setting of static IPs (192.168.1.4 and 192.168.1.6 are permitted)
Model : TD-W8951ND
Hardware Version : V3
Firmware Version :
ISP : BSNL DATAONE
my tablet show wifi status connected ... signal quality... but cant access internet ...
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : Latest
ISP :
In trying to make sure it was NOT wide open to the internet (amongst many other problems of setting it up, which I ,may address later if I can actually connect to the thing ever again) I told it to only accept connections from a range of address inside the LAN. Now it wont accept anything except telnet from the LAN.Short of wiping out 6 hours of trial and error configuration and resetting it, are there any other options I can exercise via the telnet interface?
Region : Malaysia
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : V5
ISP : Streamyx
TD-W8951ND V5 No longer have Mac Spoofing support.i just bought this modem since my old one is faulty. and i realize that my modem is V5 my previous modem is V4 and there is Mac Spoofing support there.
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
My router TD-W8951ND remembers only a dozen of latest logs. Previous, older logs disappears. Why? Is there any way to force router to keep logs from, for example, the last 12 or 24 hours?It is important to me because i have some problems on my adsl line and i want to know what happens with connection while I am not in home or when I sleep.If it will be necessary I am able to log onto my router using Telnet, just give me required commands to fix this problem with logs.
Region : India
Model : TD-W8951ND
Hardware Version : V5
Firmware Version :
4 lan ports problem in my modem. Able to get internet through wifi but unable through lan ports.checked in 2 pcs and 1 laptop
Region : India
Model : TD-W8951ND
Hardware Version : V4
ISP : MTNL
I m using TD-W8951ND wifi router with MTNL connection. The LAN connection with PC works just fine but i m not able to connect my iphone or ipad with the router. I have reset the router many times and also retored my iphone but still no luck. Pl tell me what are the settings needed for wifi connections.. Currently i have set the wireless mode to 802.11 b+g+n. Setting it to just 802.11 b sometimes connects with the iphone but never with ipad.
-Region : Poland
-Model : TD-W8951ND
-Hardware Version : V5
-Firmware Version : 5.0.0 Build 120522 Rel.23978
-ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
Region : Poland
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120522 Rel.23978
ISP : Orange/TPSA
On my router TD-W8951ND constantly there are the same type errors, while using computer conected to the router:
Code:
2/16/2013 17:24:8> netMakeChannDial: err=-3000 rn_p=80544b08
2/16/2013 17:24:13> Last errorlog repeat 2 Times
[Code].....
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : TD-W8951ND_v5_120522
ISP : N/A
The wireless adapter settings page has an entry for 'PIN' and 'PBC' for WPS.Selecting either always results in the client station requesting the routers pin, indicating that the pushbutton selection is not working properly.The router was doing this with the version of hardware that it was shipped with. i have downgraded to 120522 and the router is behaving exactly the same.Has anyone successfully configured the router for pushbutton connection? do not suggest that we use the pin setting as we have a requirement for dumb devices to connect to wireless and they only support pushbutton connection.
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 22.05.2012
ISP :
I have a TD-W8951ND v5 on the latest firmware.
I recently broke my broadband data cap which surprised me as I had not been using the internet much.
I only have tablet which I switched off having first checked the router to make sure there were no other wireless connections and adding MAC address filtering to be sure no one else was stealing my bandwidth. With just my router connected to the ISP, my ISP has recorded 170MB of downloaded data in 3.5 hours. Switching off the router stops the traffic being recorded (as you would expect), but when switched back on the large data transfers start up again.
I have plugged in an older router (not wireless) and no traffic is generated, so it seems to be the TP-Link router rather than my ISP or ADSL circuit that is at fault.
Region : Australia
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N_V4_130205_Beta
ISP : TPG
I have an Optus Home Zone (mobile cell tower) that requires ports open.
Port
123 UDP
500 UDP
4500 UDP
I have assigned the Home Zone a Static IP outside the DHCP range and set the above Ports on the NAT, Virtual servers to that IP address.
I have used nmap to scan the ports and it provides open/filtered status for all of them.
Here is the kicker for me, i use a DGN3500 netgear (which keeps dropping WiFi hence its replacement) and enter the ports and it works straight away. Un plug and put the Tp-Link and nothing.
I use Eset Smart Security, could that be the problem?
Region : CzechRepublic
Model : TD-W8901GB
Hardware Version : V3
Firmware Version : 100820
ISP : Vodafone
I have a question. Is possible for my model 8901GB v3.4 set IP adrress reservation ? I didnt find how to do it.
Region : Ireland
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N
ISP : Vodafone Ireland
I am having a rather annoying problem. I run a small hotel (just 3 floors) and my modem gives a strong enough signal to provide wireless access to everybody in the house however I'm finding that a lot of people, whilst they can connect to the modem, cannot browse online. Connection just times out when they open their browsers.Recently a guest gave me his laptop and asked me if I could do anything with it. I'm by no means an expert when it comes to this kind of thing so I chanced my arm by putting his MAC address into the CP's Wireless/MAC Filter page. He connected immediately and was able to go online much to my relief.
Thing is, I don't want to have to do this for every guest that comes through my door! Is there any way everybody who has a laptop can connect without me manually entering their MAC addresses? MAC restrict mode is set to 'disabled' but I thought that would allow everybody unrestricted access?
I need a new ip address form my provider.I now that thy work with the mac address,How van i cahnge that in my dlink 655
View 5 Replies View RelatedI have 3 Dcs-3420's on the same network same static ip setup and they never have issues. Im testing 1 942L, I've upgraded firmware to1.11, but periodically the camera loses its ip address which is weird because it is set static. My wireless is set to Mac address security. Now camera is outside in a shaded area, over night the camera worked all night, this morning it has reset three times. Additionally, each time it resets/losses ip address it also loses the manually set time.
View 1 Replies View RelatedI am having a problem which I can't seem to find a way around. I have a DIR-615 E3 that I'm unable to get IPv6 to work properly on.I'm connecting to IPv6 over PPPoE, and I'm unable to change the 'IPv6 LAN Address' to an IP my provider has given me. They've provided a native address in the 2607:: range, however on the router it's stuck at a 6to4 IP which is NOT what they've given me (2002:CEF8:8B79:: IP).
I'm thinking of buying a new router that either has better IPv6 support, or one that supports OpenWRT and working my way through that.
My old modem from Roadrunner (Time Warner) died and the service man replaced it with a Arris TG852 modem/router. then my problems began. I would like to have the Arris modem act like a modem and not a router. The network governed by the DIR works fine but none of the clients can connect to the internet. Below are the steps I have tried.in both steps below, The DIR is connected to the Arris using the Ethernet not the Wan port.
1. I tried disabling DHCP on the Arris router and setting a static IP address for the DIR router. This worked for a bit and then quit. Some of the computers said there were duplicate IP addresses on the network. If fact the same IP address showed up in the DNS list of the Arris and the DIR routers.. even though the Arris router had DNS disabled.
2. After reading other forums. I enabled DHCP on the Arris and set it to passout IP address between 192.168.0.2 and 192.168.0.99. I then setup the DOR to pass out addresses between 192.168.0.100 and 192.168.0.200. then moved the DIR into the DMZ of the Arris. Still no access to the internet.
Using Android phone and have to set up Port Forwarding to access the cameras. I have to change the IP Address to a static one instead of the one issued by the Router. How do I change the IP Address of the camera to one outside the DHCP range?
View 14 Replies View Relatedi have TP link router model no TD W8951ND.. i can access internet but wifi disconnects in every 5 mins.. i have to connect again but as soon as i got connection after 5 or 10 min it disconnects again..
View 1 Replies View RelatedI have a TP-LINK TD W8951ND wireless Modem+Router which contains one RJ11 (phone line) port and four RJ45 (Ethernet) ports along with wireless N support.
Now for some reason, my TP-LINK modem doesn't work with my ISP, whereas the modem provided by my ISP works. If I wish I could get the basic modem provided by my ISP which contains one RJ11 port and one Ethernet port.
So can I link both the modems? I mean will this configuration work: Connect telephone cable to basic modem provided by ISP. And then connect the Ethernet port of basic modem to the Ethernet port of TP-link modem. And then connect remaining Ethernet ports to PC and laptop and simultaneously use WIFI.
Will it work or should I have to replace my TP-Link Modem+Router?
I now have a tp link td w8951nd.
The problem is, I wanted to log into the router to reconfigure some of the settings and to see if I have the option of using a VPN, only the router will not let me connect. I pinged the router and established that the installation engineer had changed the default LAN ip but whenever I try to navigate to this ip address by. Browser (Firefox) says unable to connect.I have tried a wired connection and rebooting procedures.
I need assistance regarding changing of DYNAMIC WAN IP to desired WAN IP to connect my e-mail server of my office, Problem is :i have a dynamic WAN IP at my home internet router , and my e-mail server at office only allows assigned WAN ips to connect , I want to connect from my home, i know the WAN ips which are allowed to connect my e-mail server and i want to change my dynamic wan ip virutally to desired WAN ip for incoming and outgoing traffic from my wireless router, What I need to do :I need to change my dynamic WAN IP to an static desired ip at my wireless router?
View 4 Replies View RelatedHow do I change my cisco wireless from a dynamic setting to a static settings.
View 1 Replies View RelatedI have a couple of Linksys WRT54GS V7 routers, they work fine, with the exception that when I login to the web interface, I select the drop down box for DHCP to change it to a static IP, the page refreshes, but comes right back to the same screen with DHCP selected again, I can change the time zone with no issues, I entered the Static DNS info. I've tried a couple of different PC's with a couple of different IE versions. I already updated to the newest firmware, firmware is 7.50.8, I've also factory reset it a couple of times, and I've just run into a brick wall. I've setup hundreds of these routers before so it's not like I don't know how.
View 3 Replies View RelatedRegion : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
Region : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
[code]...
