Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
[code]...
Region : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Infostrada
My TD-W8970 freezes randomly, sometimes several times a day, sometimes less, but now the problem it's more frequent and I suppose it could be generated by some internal component that could have a abnormal behavior.Anyway, this happens in different situations, either using all the functionalist, or being only on and in idle state. Last time was few minutes ago, when all the system were shuttled down and only router was on.
Region : Others
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
I just set up DDNS for my home, and also set forwarding port 5000 for my NAS with an specific IP address 192.168.1.xx. Then, I use my office Internet to call DDNS xxx.dyndns.org:5000 to connect the NAS in my home, It is working OK (from outside to home) However, if I call xxx.dyndns.org:5000 by my home Internet, it is not working (from inside home to home). But if I directly call NAS' IP address 192.168.1.xx:5000, it is OK to reach it. So I think, DDNS used behind TD-8970 (inside home) is not working. TD-9870 is not forwarding port.
I don't know what do I miss in setup this WD-8970.
My previous Zyxel wireless router modem can allow me to us DDNS behind it with out any extra setting. Is it possible that there is still some bug in Firmware of this TD-8970?
Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n
ISP : plusnet
I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.
Both tunnels are similarly configured:
Tunnel 1 on my TD-W8970
IPSec Connection Name: Tony1
Remote IPSec Gateway Address(URL): 89.240.xx.xx
Tunnel access from local IP addresses: Subnet
IP Address for VPN: 192.168.1.0
IP Subnetmask:255.255.255.0
[URL]
Region : United Kingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : O2
I have sent the following trouble ticket to TP Link Support hoping they can shine some light/fix a VPN issue I am experiencing with the TD-W8970 router.
Please see the text below.........
I have 2 tunnels set up on my TP Link TD-W8970 and although both of these work for a a while, they both drop out after 24-36 hours for no apparent reason. The tunnels still show as "up" in the router, but I lose PING and connectivity to my remote systems. The only thing that seems to fix this is to reboot the router.
I have tried the tunnels with and without "DPD" (Dead Peer Detection) enabled and the results are the same.
I have 2 other friends who have the exact router with the same firmware (latest version), and they too have the same issue.
There is nothing in the logs showing any disconnection of the VPN, and as I have mentioned, the tunnel still shows as "up" on both ends. Its almost as if the service has stopped running, but I cannot check this.
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Telecom
Below you point out my attenuation values detected on the modem in question:
Line Status:Connected
DSL Modulation Type:ADSL_2plus
Annex Type:Annex A
UpstreamDownstream
Current Rate (Kbps)4768124
Max Rate (Kbps)104811512
SNR Margin (dB)28.412.2
Line Attenuation (dB)17.233.4
Errors (Pkts) 0 0
The part adsl should be revised as the highlighted value and too discordant from the value taken on the same line as route draytek 2800 with attenuation of 24.5 db snr to 16dB, I'd like to find a job in the next firmware dedicated all'ottimizzare driver adsl modem so is worse than 6 years old
Region : UnitedStates
Model : TD-W8970
Hardware Version : V1
ISP : CenturyLink
Just installed new W-8970 via centuryLink ADSL, connected two computers (hard wire) which work fine. I also have it connected by hard wire to my Direct T.V DVR Model HR 24 to run T.V app's such as Pandora music etc. It will only stay connected for 5-10 minutes then drops out, any suggestions other then buying a different brand modem/router.
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
Region : Others
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I am struggling to get a printer added through the print server. The printer is set up in the TP-Link USB Printer Controller and selected as the auto-connect printer. I can scan through the server, but can't add the printer in control panel or see it as a option when printing. The printer is a Samsung SCX-340F.
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : wind infostrada
TD-W8970 Wireless connection problems|
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Wind Infostrada
That's a wonderful router on the paper! Really it has some problems with the wireless connection and the dhcp server. After 2 days of i must forced to reset the router because it refuse any wireless connection while the internet browsing on the other pc connected via ethernet ARJ45 is very slow.To complete the scenario the router doesn't allow any acces to his console page ..so what's the problem?
I try to change any channel for the wireless without no positive result.I bought it on amazon but if this situation will continue without any solution from tp-link i will forced to send it back with a totally negative feedback on the product.
Region : Australia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I am trying to get a windows 7 laptop to connect to a TD-W8970.
Region : India
Model : TD-W8151N
Hardware Version : V3
Firmware Version : 120530
ISP : BSNL
Net is working smoothly from LAN, but no success on wifi. Over wi-fi, I can connect to router but cannot access net.
Model : TD-W8951ND
Hardware Version : Not Clear
Firmware Version :
ISP : Metronet BPL
I connect to the internet by BPL modem on electricity , for using my modem's wireless feature ı have to close DHCP and use modem in bridge mode, otherwise I can't use wireless, And my problem is connecting to the internet with my LG 42LM640S smart tv using wireless, When I talk with LG techinal service they came and try to connect tv to the internet with using their android phone's hotspot feature, my tv connect with phone's hotspot feature to the internet,So they said that "you have to change tp link modem's encoding system?Now it's encoding mode in WPA enconding system :S But whwen ı shut down encoding wireless tv didn't connect again?
Region : Others
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 2.0.0 Build 120427 Rel.09135
ISP : True
I just bought the wireless router as stated in the subject and I cant get 2 of our PC�s to connect wirelessly for some reason. 4 other PC's are fineAll machines running windows 7, but when the authentication type on WPA2-PSK the 2 computers ask for a password which we put in but keeps saying its wrong, but infact its right.I can connect them on WPA-PSK, but then all the computers drop out after 30 seconds.
Region : UnitedStates
Model : TD-W8961ND
Hardware Version : V2
Firmware Version :
ISP : ATT
I want to add more users to my home network and I couldn't, at this moment I only can connect 8 devices (12 devices at least) when I try to connect the next one its impossible, but if I take off one of the connected devices then the router allows to connect the new one.How can I connect more than 8 devices to my router ? (wireless)Also, is there any limits with Wireless MAC Address Filter ? because I can't add more than 8 MAC addresses in my old router I could do that.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : BSNL
I Bought thisTD-W8968 a month back.. It was working alright till a few days back. From the past 3days i'm experiencing internet light and DSL light going off...The DSL light is not constant even for 5min...When the DSL light comes up, the internet light takes almost 5min to comeup or before internet light come up the DSL light goes off.There wasn't problem with my old UT star modem..I already checked,its running fine without disconnection..When i replace it with TD-W8968 router ,the problem continues.. When my internet connection was good...The SNR margin was like 25 for upstream and 31 for downstream...After 2 days it went mad. here are the images shows about current reading..Fluctuates between 0.2 - 100 upstream and 2-35 for downstream
Model : TD-W8968
Hardware Version : V1
Firmware Version : ?
ISP : CenturyLink
I need the setup info to connect the TD-W8968 to CenturyLink.
Region : Indonesia
Model : TD-W8151N
Hardware Version : V3
Firmware Version :
ISP :
Recently I bought TD-W8151N wireless adsl router, I have one desktop computer that connected to TD-W8151N via ethernet and wirelessly to one laptop, IP Addr: 192.168.1.4, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : desktop (LAN connection IP Addr: 192.168.1.3, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : laptop (wireless connection) but I can't ping each other and also can't access the share folders between them., both computers can access internet. Is there anything I missed the configuration setting of the router? Before I use wireless, I connected this 2 computers using cross-type utp cable, and working good.
Region : India
Model : TD-W8901G
Hardware Version : V6
Firmware Version : 6.0.0 Build 120418 Rel.34102
ISP :
Everytime, I turn on the ADSL2+ wireless modem router, it connects to the internet and my laptop gets paired with the wireless network but after 30 mins time, wireless ADSL2+ router restarts itself and goins in a loop for nearly 5 times and then it gets connected to internet but then I cannot connect my laptop to the the router using wireless with error DHCP failed to assign IP but DHCP is enabled in the router. This has started since a month and I had tried several network change settings but nothing has given me a solution. I do use Kaspersky IS through which the connection flows in. My internet setting is set to use Automatic DNS discovery and most time, I get RC 102 DHCP error.
Region : Ireland
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N
ISP : Vodafone Ireland
I am having a rather annoying problem. I run a small hotel (just 3 floors) and my modem gives a strong enough signal to provide wireless access to everybody in the house however I'm finding that a lot of people, whilst they can connect to the modem, cannot browse online. Connection just times out when they open their browsers.Recently a guest gave me his laptop and asked me if I could do anything with it. I'm by no means an expert when it comes to this kind of thing so I chanced my arm by putting his MAC address into the CP's Wireless/MAC Filter page. He connected immediately and was able to go online much to my relief.
Thing is, I don't want to have to do this for every guest that comes through my door! Is there any way everybody who has a laptop can connect without me manually entering their MAC addresses? MAC restrict mode is set to 'disabled' but I thought that would allow everybody unrestricted access?
I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!
View 6 Replies View RelatedRegion : Canada
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 120608
ISP : Distributel
I've just installed this router today, connected physically 2 PCs, a PS3 and a VoIP and everything works fine !
The problem is with the WIFI connection ! my devices see the WIFI network, they connect, but I cannot connect to the internet ...
What settings Should I turn on/off or any config I should tweak ?
Region : India
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : S/N: 12B79605315
ISP : BSNL Data One
I had Purchased a brand new TP-Link WifI Modem Router TD-W8961ND with S/N : 12CB5200872 from [URL] and it got delivered few days back. When I am trying to connect it to the internet the modem is not getting connected nor configured. The Power button light, ADSL Light and internet light are continuously blinking and nothing is getting steady. The modem is appearing to be a damaged piece of modem and it is very unfortunate that we have got a modem from flipkart in an unserviceable condition. It came with a warranty of 03 years and I wanted a replacement so that I can use the modem for connecting internet.
Router Model: TP-Link TD-W8970 port forwarding my modem/router. I previously was able to successfully port forward a Valve Source Server and had other people join on the internet so...(It worked) I recently reformatted and since have had issues.
I'm currently setup with PPPOA and I've added various ports for different programs (a Teamspeak 3 Server[9987] and Minecraft[25565]) either dont work. I used a port checker program and they either say the port is closed or the connection is refused...I've tried using a static IP but I think i configured it wrong becuase i was barely able to get the internet while using it, either way..the ports didn't open.
DCHP is disabled (Tried enabling, didn't work) The above ports are enabled with Windows firewall (inbound+outbound) and Im not using any Anti-virus software to block the ports. Windows 7 64bit, fresh format and ports that wont go through.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
According to inSSIDer the router seems to be using two wifi channels (10+6) and inSSIDer is recommending to move to a standard channel (1,6,11).
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband
Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version :
ISP :
problem with filtering
Region : Syria
Model : TD-W8901G
ver 6.0
54Mbps wireless G ADSL2+:
I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."
I use a wired network connection to my neighbours Vodafone Modem (We share his monthly cost). I also have a TP-LINK 54M Wireless ADSL2+ Router from a previous broadband contract with a landline phone company. Is it possible to reset and configure the TP-LINK Router to act as a relay unit, connected to the network cable, so I can then use my laptop elsewhere in the house?
View 3 Replies View RelatedRegion : Spain
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120524 Rel.05221
ISP :
linksys1.jpg
I have wifi at home this link installed.
192.168.1.1 is a TD-W8961ND
192.168.1.4 is a linksys wrtt54gl
And I have two problems.
1) I can not see any desktops in my local net, and with old router I could see all, for example (diskstation, dm800, etc...) In my macbook air I can not see my NAS Synology and with old router I do.
2) All PCs that are conected to 192.168.1.4 have not IP. and DHCP in TD-W8961ND is activated.
