Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
Region : Australia Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
Region : Italy Model : TD-W8970 Hardware Version : V1 Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
Region : UnitedKingdom Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
Region : Italy Model : TD-W8970 Hardware Version : V1 Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n ISP : Infostrada
My TD-W8970 freezes randomly, sometimes several times a day, sometimes less, but now the problem it's more frequent and I suppose it could be generated by some internal component that could have a abnormal behavior.Anyway, this happens in different situations, either using all the functionalist, or being only on and in idle state. Last time was few minutes ago, when all the system were shuttled down and only router was on.
Region : Others Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP :
I just set up DDNS for my home, and also set forwarding port 5000 for my NAS with an specific IP address 192.168.1.xx. Then, I use my office Internet to call DDNS xxx.dyndns.org:5000 to connect the NAS in my home, It is working OK (from outside to home) However, if I call xxx.dyndns.org:5000 by my home Internet, it is not working (from inside home to home). But if I directly call NAS' IP address 192.168.1.xx:5000, it is OK to reach it. So I think, DDNS used behind TD-8970 (inside home) is not working. TD-9870 is not forwarding port.
I don't know what do I miss in setup this WD-8970.
My previous Zyxel wireless router modem can allow me to us DDNS behind it with out any extra setting. Is it possible that there is still some bug in Firmware of this TD-8970?
Region : Portugal Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom Model : TD-W8970 Hardware Version : V1 Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n ISP : plusnet
I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.
Both tunnels are similarly configured:
Tunnel 1 on my TD-W8970 IPSec Connection Name: Tony1 Remote IPSec Gateway Address(URL): 89.240.xx.xx Tunnel access from local IP addresses: Subnet IP Address for VPN: 192.168.1.0 IP Subnetmask:255.255.255.0
Region : United Kingdom Model : TD-W8970 Hardware Version : V1 Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n ISP : O2
I have sent the following trouble ticket to TP Link Support hoping they can shine some light/fix a VPN issue I am experiencing with the TD-W8970 router.
Please see the text below.........
I have 2 tunnels set up on my TP Link TD-W8970 and although both of these work for a a while, they both drop out after 24-36 hours for no apparent reason. The tunnels still show as "up" in the router, but I lose PING and connectivity to my remote systems. The only thing that seems to fix this is to reboot the router.
I have tried the tunnels with and without "DPD" (Dead Peer Detection) enabled and the results are the same.
I have 2 other friends who have the exact router with the same firmware (latest version), and they too have the same issue.
There is nothing in the logs showing any disconnection of the VPN, and as I have mentioned, the tunnel still shows as "up" on both ends. Its almost as if the service has stopped running, but I cannot check this.
Region : Italy Model : TD-W8970 Hardware Version : V1 Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n ISP : Telecom
Below you point out my attenuation values detected on the modem in question: Line Status:Connected DSL Modulation Type:ADSL_2plus Annex Type:Annex A UpstreamDownstream Current Rate (Kbps)4768124 Max Rate (Kbps)104811512 SNR Margin (dB)28.412.2 Line Attenuation (dB)17.233.4 Errors (Pkts) 0 0
The part adsl should be revised as the highlighted value and too discordant from the value taken on the same line as route draytek 2800 with attenuation of 24.5 db snr to 16dB, I'd like to find a job in the next firmware dedicated all'ottimizzare driver adsl modem so is worse than 6 years old
Region : UnitedStates Model : TD-W8970 Hardware Version : V1 ISP : CenturyLink
Just installed new W-8970 via centuryLink ADSL, connected two computers (hard wire) which work fine. I also have it connected by hard wire to my Direct T.V DVR Model HR 24 to run T.V app's such as Pandora music etc. It will only stay connected for 5-10 minutes then drops out, any suggestions other then buying a different brand modem/router.
Region : Others Model : TD-W8968 Hardware Version : V1 Firmware Version : ISP :
I am struggling to get a printer added through the print server. The printer is set up in the TP-Link USB Printer Controller and selected as the auto-connect printer. I can scan through the server, but can't add the printer in control panel or see it as a option when printing. The printer is a Samsung SCX-340F.
Region : Italy Model : TD-W8970 Hardware Version : V1 Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n ISP : wind infostrada TD-W8970 Wireless connection problems|
Region : Italy Model : TD-W8968 Hardware Version : V1 Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n ISP : Wind Infostrada
That's a wonderful router on the paper! Really it has some problems with the wireless connection and the dhcp server. After 2 days of i must forced to reset the router because it refuse any wireless connection while the internet browsing on the other pc connected via ethernet ARJ45 is very slow.To complete the scenario the router doesn't allow any acces to his console page ..so what's the problem?
I try to change any channel for the wireless without no positive result.I bought it on amazon but if this situation will continue without any solution from tp-link i will forced to send it back with a totally negative feedback on the product.
Region : Spain Model : TD-W8961ND Hardware Version : V3 Firmware Version : 3.0.0 Build 120524 Rel.05221 ISP : linksys1.jpg I have wifi at home this link installed. 192.168.1.1 is a TD-W8961ND 192.168.1.4 is a linksys wrtt54gl
And I have two problems.
1) I can not see any desktops in my local net, and with old router I could see all, for example (diskstation, dm800, etc...) In my macbook air I can not see my NAS Synology and with old router I do.
2) All PCs that are conected to 192.168.1.4 have not IP. and DHCP in TD-W8961ND is activated.
Region : Others Model : TD-W8901G Hardware Version : V6 Firmware Version : 6.0.0 Build 120213 Rel.30335 ISP : ETAPA
I am writing in from Cuenca, Ecuador. I have a TD-W8901G Wireless ADSL2+ Modem Router. I have accessed the interface using the default ip address:192.168.1.1.When I select Interface Setup from the menu, it only shows Internet and LAN as the only 2 options. Wireless is no longer there. It just disappeared! The LED indicator light for WLAN is also "OFF." When you try the Quick Start wizard guide, it cannot complete the setup because there is an IP address error.
I have changed the firmware 2x since, trying to remedy this, I have also tried factory resets at least 3x. Nothing has worked up to this point.
Region : France Model : TD-W8151N Hardware Version : V3 Firmware Version : latest ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
-Region : Poland -Model : TD-W8951ND -Hardware Version : V5 -Firmware Version : 5.0.0 Build 120522 Rel.23978 -ISP : Orange/TPSA
Is there any way to change web interface / firmware from orange version to blue version? Blue version has more options and better "System log" presentation page.
Region : Sweden Model : TD-W8968 Hardware Version : V1 Firmware Version : 0.6.0_1.1_up(120926) ISP : HessleholmNetwork
My TD-W8968 has begun to freeze up. It had been running for about two hours before this happened. It's a "slow" process that starts with the web interface being unavailable, i'm unable to connect to the modems web interface.And at about the same time it becomes impossible to connect new devices to the wireless network. Right about this point i did a speed test over the modem and performance was abysmal.It was so slow that my web browser believed that it was offline! But i was able to re run the internet speed test once more before it totaly locked up! At this point it was impossible to use the TD-W8968.
This was the,, i don't know,, perhaps the fifth time it happened in a row. It has been running perfect for two months before it began acting up like this.I have done a reset of the modem, didn't solve the problem.I have also done a reflash of the firmware, i've had the latest firmware since i bought the TD-W8968. But the reflash didn't solve it
My router is the WRT160N, and it doesn't display the version number on the bottom which according to your website means my router is a VERSION 1.SO, why is it that my router says it has:
Firmware Version: v1.53.0 Dec 19, 2007 And the latest firmware is Firmware 11/08/2010 Ver.1.02.11
That looks like an EARLIER firmware version to me judging by the firmware version yet it is dated later. **bleep**. If you want, I can upload a photo of my router's model no. for all to see.My question is, am I safe to 'upgrade' to this 'earlier but dated later' firmware version or not? Why is mine showing as having a later version.
I have a E4200 setup for 2.4 & 5G running the latest firmware. When I connect to the router wireless 192.168.1.1 and log in, it takes a few seconds for the web interface to display. Same happens when switching to the different config tabs. Is there any reason for this? I would think it would be immediate but it takes anywhere from 3-5 seconds for IE9 to respond.
I've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1) Technical Support: [URL]
Router Model: TP-Link TD-W8970 port forwarding my modem/router. I previously was able to successfully port forward a Valve Source Server and had other people join on the internet so...(It worked) I recently reformatted and since have had issues.
I'm currently setup with PPPOA and I've added various ports for different programs (a Teamspeak 3 Server[9987] and Minecraft[25565]) either dont work. I used a port checker program and they either say the port is closed or the connection is refused...I've tried using a static IP but I think i configured it wrong becuase i was barely able to get the internet while using it, either way..the ports didn't open.
DCHP is disabled (Tried enabling, didn't work) The above ports are enabled with Windows firewall (inbound+outbound) and Im not using any Anti-virus software to block the ports. Windows 7 64bit, fresh format and ports that wont go through.
I have extension mobility configured and working fine. Except that when you log into the phone, the phone does not exit back to the main display. To get back you either need to exit out of the menus by pressing exit a few times or press the globe / web button on the phone.
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
I have an issue with the syslog of 7600 router, I have configured the logging level to informational, but when I execute changes such as up or down an interface, the syslog messages aren't displayed? Why is the reason? This symptom exist after I changed the buffer size from default to 32768.
Router#sh log Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 2 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: disabled Monitor logging: level debugging, 40 messages logged, xml disabled,
Downloaded DVIEWCam 3.0. Are there any plans on supporting older Dlink Cameras like the DCS-2100 etc ...? Even my DCS-3220 is not fully supported, however the 3420 worked in the config menu.
Went to log into the web admin interface on my SG-300 today and I get this in both IE and Firefox:
I'm not able to login by typing user/password and just pressing enter. I've tried power-cycling the switch, however, since the power cycle, the font-panel system LED has been blinking green. I seem to recall, though I can't locate the reference now, that this means the switch is running with factory settings, but that cannot be right because:
1. I had previously saved a new configuration on the switch, which it should be using now.
2. It is answering on the configured non-factory IP address -- just not rendering the web admin interface successfully.
I've had this unit for approximately a month. This is not the first issue I have had with this unit (see: [URL] and I'm experiencing some strange LAN speed issues since I installed it. Do I need to RMA this thing?
We've recently shut down an interface on one of our ASA 5510s as we no longer use that service provider. The dashboard, however, still insists on showing traffic usage on this interface. How do I change the dashboard to display a more meaningful interface?
I have a ASA5540 firewall set-up with an interface MTU of 1500.
I suspect that we are receiving packets with a larger MTU but have not found an easy way of confirming this. Any command that can be run on the firewall to display the MTU packet size being received on an interface?
We are also running Solar Winds so could query an OID if such a variable exists.
Region : UnitedKingdom Model : TD-W8968 Hardware Version : V1 Firmware Version : latest ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
Region : Argentina Model : TL-WR1043ND Hardware Version : V1 Firmware Version : ISP :
Region : Romania Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.4 Build 110429 Rel.3 ISP : Romania Data Systems RCS-RDS
Proud owner of TL-Wr1043ND, great piece of technology and very affordable.
Question is: in the Administration GUI, is there a way to set it up so it displays PC-Name instead of MAC address in sections such as MAC Filter, Statistics, Logs etc?
Every time I check stuff I need to compare MAC address with PC name in order to find out who's who; so it would be nice to see directly PC Name.
