N300 ADSL2+ Modem Router DGN2200v3 - Wired Connection Doesn't Work / Wireless Does
Mar 11, 2013
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies
ADVERTISEMENT
Oct 21, 2012
Nearly every morning/evening I have to re-boot my router to get internet access. Netgear N300 ADSL2+ modem router Model DGN 2200 (had about a year), Windows 7 64bit Home premium Laptop connected wirelessly, Windows 7 64Bit Home Premium desktop connected by LAN cable. ISP BT Internet. Until recently this set up has been working OK with occasional loss of interent access and need to re-boot router. The internet light has been showing red on those occasions. Over the last two weeks I have found that when I turn one of computers on although all lights on router are green I have no internet access. I have to re-boot, then all is OK until the next day when I have to re-boot again. My phone line appears OK with no noise on line, no reported problems on BT broadband staus. The thing that puzzles me is that the lights are all green on the router yet my networking icon on the pc shows an exclammation mark and 'no internet access' and I do not have access to net.The wireless connection is OK with excellent strength.
View 7 Replies
View Related
Dec 11, 2012
how to properly configure 2 different hardware devices to extend the current wifi signal of my home network.I'm using a Motorola SBG6580 DOCSIS 3.0 cable modem as my primary access point (AP) and a Netgear N300 DGN2200v1 ADSL2+ modem router which will function "behind" the SBG6580 in repeater mode. I previously had DSL for my internet connectivity but recently switched to broadband cable for faster speeds.Due to the layout of my home, I cannot physically connect the Netgear router to the Motorola modem via ethernet cable and need both devices to communicate wirelessly. I have already done extensive reading on this subject and best practices suggest that, whenever possible, both units should be the same brand/manufacturer. The Netgear appliance does have the capability of being configured as a repeater so if I don't have to buy a "network extender" that would be my preference.I understand that both units must be configured to have the same SSID, subnet, wireless channel and security encryption. In repeater mode the Netgear router can't be configured to use WPA2-PSK so I need to use WEP instead.
View 1 Replies
View Related
May 13, 2012
I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!
View 6 Replies
View Related
Jun 9, 2012
I am looking for a wireless router with the following features for less than $80.
Gigabit Ethernet
802.11n 300Mbps
Open source firmware support (optional)
I found a few of these on newegg but all of them have reviews which claim that these routers drop the wireless signal every so often and need to be reset. I have a router that has the exact same problem but it is very old now and so I understand. But a new router with this problem is not acceptable.
[URL]
View 2 Replies
View Related
Nov 7, 2012
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
View 6 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Dec 30, 2011
I got a brand new wireless router and made it the first in line with my cable modem. This is necessary because I want to take advantage of all the features in the new router. I put the RTP300 behind the first router and switched off DHCP and connected the internet port into one of the 4 regular ports on the back (typical configuration for a pass through router).So everything works perfectly for any computer attached to the router (they can access the internet etc). The only problem I have is the VOIP doesn't work. If I pick up my phone it says this device is not registered to a phone number.
View 1 Replies
View Related
Feb 20, 2013
The main router is Belkin N300 and the new one is D-Link N300 DIR-651 for extended range.
View 1 Replies
View Related
May 7, 2012
When I start up my computer I cannot get an Internet connection. To get a connection I have to go into Control Panel, open Device Manager, click on Network adapters, which opens Realtek PCIe GBE Family Controller. I uninstall the Controller, restart and I then get an Internet connection. The Realtek controller then re-installs itself. I am using Windows 7 Home Premium operating system on my desktop. I am wired through a Dynalink RTA 1320 Rev 2 ADSL2+ Modem Router (provided and checked by my ISP). I have a Netgear Wireless N Router WNR 2000 for wireless connection to my laptop which has a Vista operating system. I have no connectivity problems to the laptop. I have had the connections checked by my ISP and the Netgear router by Netgear. They have both confirmed that there is connectivity to the desk top and the laptop and that the connections are working. Both have said that there is an issue with the operating system. I have got all the latest drivers installed and I get the message "Best driver software for your device is already installed".
View 10 Replies
View Related
Dec 29, 2012
I have recently purchased a Belkin n300 wireless N router. The problem is, I have to reboot the thing numerous times throughout the day to allow a client to connect to it via wireless. One client will be connected and then drop, or a client will be connected, and I cannot connect another device. I also had an issue with streaming over wireless for netflix on my devices and the only way I could get it to work was to turn off the firewall, what the hek.... This is crap. I knew I should not have bought a belkin router again. Had one years ago and it constantly gave me issues. Had my Linksys Wrt54G for years with no problems until it finally crapped out. Anyways, my firmware version is the latest version according o the website.
View 6 Replies
View Related
Mar 25, 2011
I installed a Micro Edition of Windows 7. Everything is going properly with it except the wireless internet connection (its driver is installed and working properly as shown in Device Manager), by click Connect and typing the PW, it tries for few minutes then fail in connecting putting a yellow small circle on the wireless icon in Task bar
View 1 Replies
View Related
Oct 29, 2012
I just got an used Pc from auction today.I installed it with Xp Pro. I am trying to connect it to my wire modem but it doesn't work.
View 4 Replies
View Related
Apr 3, 2011
I tried to set up a wireless router yesterday and when trying to connect with my laptop it had limited or no connectivity. I tried a few things but I couldn't get it to work so i switched back to my wired connection. Trying to set up the wireless router is not my concern though at the moment. Now my desktop can connect to the internet but my laptop and ps3 can not obtain an ip address. My desktop does not have a wireless card, thats the only thing I can think of why it will work when the other devices dont.
Right now I have my cable modem hooked up to a D-Link switch with my desktop and laptop connected. The desktop can connect and I get a limited or no activity with my laptop. I have reset the modem multiple times, restarted computers, Right clicked on my connection and tried to repair it, connect the laptop straight to the modem and did all of the above again. The IP and DNS are set to obtain automatically. Nothing is working that I know of but I can plug in my desktop and its up and going in 2 seconds.
The router was a very old one given to me from a friend. Its a Linksys V1. It is not connect to anything or even on now. The last time I tried to use this router I didn't get it to work and this same thing happened. I took it into work the next day and they were able to connect via wireless and wired using my D-Link switch. When I got home it work again just fine.
View 14 Replies
View Related
Feb 27, 2012
Just 2 days ago I realized that the wired connection will not let me connect to the internet at all. However, I have a wireless connection and it lets me connect to the internet. I don't like using the wireless connection unless necessary. I tried updating the drivers and troubleshooting, and it still won't connect. It still has that exclamation mark for the wired connection. I use a Windows 7 laptop.
View 17 Replies
View Related
Mar 13, 2013
I try connecting via ethernet cable and it doesn't seem to work until the administrator of the network (my brother) comes home and then turns his computer on and starts using it. However, if i switch to a wireless adapter it sometimes works (like right now) even when my brother is not using the internet. Also, i tried to connect via wifi on my macbook pro to the same server and it used to work flawlessly 100% of the time, now i can only connect once in a while for short periods of times.
View 1 Replies
View Related
Feb 26, 2011
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies
View Related
Apr 3, 2013
I recently bough a belkin router (Share N300) but it just wont connect to the internet.My setup is as follows:ADSL -> Modem -> Router -> PCThe internet works fine when I connect it directly to my PC (via the modem), and other PCs too.So no issue of MAC address lockdown.I've tried connecting through static mode with the data from ipconfig /all, but it still doesn't work.I've even installed DD WRT and Tomato to no avail.
View 2 Replies
View Related
May 4, 2013
Region : Canada
Model : TD-W8960N
Hardware Version : V1
Firmware Version :
ISP : Bell Canada
Can I use TD-W8960N an additional router with my ISP bell router. Will it increase my speed and range of internet in my home.
View 1 Replies
View Related
Oct 16, 2012
Region : Egypt
Model : TD-W8961ND
Hardware Version : V3
Firmware Version :
ISP :
my router is placed in my home. i want to access to it with IE from my office.but no luck.also i try to ping the WAN ip address of the router.
View 2 Replies
View Related
Jan 2, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
View 2 Replies
View Related
Oct 12, 2012
We recently acquired an internet connection. Connecting via LAN works fine for me but not to my room mates. We're all using Windows 7. Windows troubleshoot it and says "Local Area Connection doesn't have a valid IP configuration" on their laptops. What should we do?
View 5 Replies
View Related
Jan 30, 2013
If the Belkin Surf N300 (Model No F9J1002v1) is CN21/ADSL2 compatible? It doesn't mention it on the box and try as I may I can't get through to tech support UK as I keep getting cut off and the J model router is not recognized on the UK website only the K
View 1 Replies
View Related
Apr 13, 2012
I have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP :
Subnet :
Default Gateway :
Primary DNS :
Secondary DNS :
MAC of the Registered Computer :
View 2 Replies
View Related
Oct 12, 2012
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
View 6 Replies
View Related
Apr 9, 2013
Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
View 1 Replies
View Related
Mar 10, 2013
I live in student accommodation and the other day my wired connection to the port in my room suddenly stopped working and the error message in the thread title appeared in troubleshooting.
View 2 Replies
View Related
Jan 15, 2012
like today randomly my internet went down. And then everything changed back to its original like my SSID from Netcom it changed back to wireless and everything was default and also the PPP was off so i wasn't able to connect to the internet. So i went to my router setup page on the internet or whatever and turned it back on. So now like the internet on my computer which has a cable to the router works but the wireless internet doesn't work for my laptop nor ipod. I can see the connection on the laptop and ipod but when i try to connect it keeps saying that it is unable to connect.
View 7 Replies
View Related
Mar 29, 2011
I have this Belkin wireless g router, which I had for a year. I was using the wired connection since then until I, at last, was able to use it's wireless connection but it only lasted around a week. After that, the modem light on the router kept on blinking and the internet light wouldn't turn on. I also couldn't connect to the router anymore(wired and wireless), neither could I configure it. I reset it but it still didn't work.
View 1 Replies
View Related
Oct 26, 2012
I bought the Linksys E900 Wireless-N300 router this evening in the hopes of hooking up my laptop to my apartment complex's wifi. I'd been previously using an ethernet cable to connect to an outlet which is also the cable connection for my television. I followed the instructions from the CD included, and I was able to successfully connect to the router, but it "cannot determine if I am connected to the internet." I added the device and MAC address to my wifi service account, and still no luck. I've tried connecting the old ethernet cable from the outlet I've been using to the router in one of the ethernet slots, with the provided ethernet cable being connected to my laptop and the 'internet' slot on the router. No internet connection. The recommendation is to "unplug the power cord from the DSL modem." I unplugged the power cord, waited, plugged it back in. Still nothing.
View 2 Replies
View Related
Apr 1, 2013
Region : Spain
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120524 Rel.05221
ISP :
linksys1.jpg
I have wifi at home this link installed.
192.168.1.1 is a TD-W8961ND
192.168.1.4 is a linksys wrtt54gl
And I have two problems.
1) I can not see any desktops in my local net, and with old router I could see all, for example (diskstation, dm800, etc...) In my macbook air I can not see my NAS Synology and with old router I do.
2) All PCs that are conected to 192.168.1.4 have not IP. and DHCP in TD-W8961ND is activated.
View 5 Replies
View Related
Oct 4, 2011
I have problem connecting Samsung (series6) TV to DIR-600. TV wired connection does not work with DLINK DIR-600 150. Is there a work around ?
Config :
DIR 600 is working in access point mode
Check list : Cat-6 Patch Cord - works (brand new works fine with laptop)TV network port - works (works fine with aztech ADSL/Switch)
View 14 Replies
View Related
Nov 23, 2012
I have just bought a n300 everything works well except i cant get my sky on demand wireless bridge to work , sky have said all ok, as have my broadband supplier. im told i need to maybe change my wireless settings in router !
View 2 Replies
View Related
