Dynalink RTA 1320 Rev 2 ADSL2+ Modem Router - No Internet Connection On Start Up
May 7, 2012
When I start up my computer I cannot get an Internet connection. To get a connection I have to go into Control Panel, open Device Manager, click on Network adapters, which opens Realtek PCIe GBE Family Controller. I uninstall the Controller, restart and I then get an Internet connection. The Realtek controller then re-installs itself. I am using Windows 7 Home Premium operating system on my desktop. I am wired through a Dynalink RTA 1320 Rev 2 ADSL2+ Modem Router (provided and checked by my ISP). I have a Netgear Wireless N Router WNR 2000 for wireless connection to my laptop which has a Vista operating system. I have no connectivity problems to the laptop. I have had the connections checked by my ISP and the Netgear router by Netgear. They have both confirmed that there is connectivity to the desk top and the laptop and that the connections are working. Both have said that there is an issue with the operating system. I have got all the latest drivers installed and I get the message "Best driver software for your device is already installed".
View 10 Replies
ADVERTISEMENT
May 16, 2011
I am trying to setup a Dynalink Wireless 4 port modem and Network Connection is showing Local Area Connection Network Cable Unplugged,Firewalled, Broadcom Netlink (TM) Ethernet even though the LED light on the cable is flashing, indicating the cable is probably working. I am operating Windows XP Version 2002.
View 8 Replies
View Related
Mar 11, 2013
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies
View Related
Apr 13, 2012
I have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP :
Subnet :
Default Gateway :
Primary DNS :
Secondary DNS :
MAC of the Registered Computer :
View 2 Replies
View Related
Dec 30, 2012
I have been using Dell Vostro-1320 laptop with Windows XP. It was running good. Recently I have installed the McAfee Internet Security software. But now I do not have internet access through this laptop although the network icon shows "connected". I have tried all the advice/solutions for such type of problem by doing Firewall off/on and changing adapter & network setting. I also updated all the drivers. But nothing works. It is notable that my other desktop is working properly in spite of installing this software.
View 4 Replies
View Related
May 13, 2012
I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!
View 6 Replies
View Related
Apr 2, 2012
i have tryed starting it on the services but that willl not do it eitheir. i have tryed almost everything and it stilll does not work. i can not access internet. plus i think a virus messed up my internet protocols. i think i removed the virus though i have been looking for an answer for 7 hours now
View 1 Replies
View Related
Jun 25, 2012
I just installed the X2000 and managed to get my Win7 Home Premium to connected to the Internet and also one wireless device. I previously had just a modem. Sometimes, when my PC is up and running, I want to disconnect it from the Internet and later connect again. There is an icon on the lower right of my toolbar which, with my old modem, allowed me to connect and disconnect but it seems to know only about the old modem. Basically it operated by starting the sequence: All Control Panel Items>Network Connections>Broadband Connection. Now this function does work; it tries to connect (through "WAN Miniport (PPPOE)") and gets "Error 651: The modem (or other connecting device) has reported an error". Can you tell me what where is the program that seems to start the Internet connection for the X2000 and if I can change parameters for the Win7 "Broadband Connection" to use the X2000? Perhaps the parameter "Connect on Demand" in the "Basic Setup" of the X2000 is involved?
View 9 Replies
View Related
Jun 8, 2012
I have been having some issues with Windows Audio needing to be restarted every time I log on. Also my theme has changed unexpectedly. I also noticed that Wndows firewall isn't started and it won't let me start it it gives me this...Could not start the Windows Firewall/Internet Connection Sharing (ICX) on local computer. Error 3 access is denied.
View 3 Replies
View Related
Mar 8, 2013
I currently have a Router that is ADSL2 & VPN capable. It currently allows me to work from home and connect to work servers securely. I have used traceroute [URL] in CMD to determine that all web requests/traffic goes through the VPN server rather than just the requests to access files on the VPN server.I don't feel comfortable having all my traffic now go through work servers(the VPN) so I would like to avoid this. I know I have 2 solutions:- Use Split Tunelling on the router where only requests to files on the VPN server will go through the VPN server, all other traffic is not through the VPN. I have heard that this can compromise the whole network as one node is currently 'unsecured' and can affect/compromise the whole network. Is this true?
- Add a second Router that doesn't connect through the VPN. When I finish work I disconnect from the VPN Routers wireless connection and connect through the second routers wireless connection. I would like to take solution 2 because I wont be compromising the whole network but I have some questions:- Is this something you would recommend?
- Is it dangerous? Is it just as compromising as solution 1?
- In Australia we use physical Phone Splitters for our internet physical connection. One side of the splitter connects to a phone line port on the wall. The other side has 2 ports, one for the phone line connection and one for the router/adsl connection. If I have 2 routers I'll need a splitter that has more than 2 ports so I can connect the 2nd router to the internet. Are there Phone Splitters with more than 2 ports and do ISP's allow me to do this?
View 1 Replies
View Related
May 4, 2013
Region : Canada
Model : TD-W8960N
Hardware Version : V1
Firmware Version :
ISP : Bell Canada
Can I use TD-W8960N an additional router with my ISP bell router. Will it increase my speed and range of internet in my home.
View 1 Replies
View Related
Jun 13, 2011
I have connected the router to my pc but can not start the connection
View 1 Replies
View Related
Oct 21, 2012
Nearly every morning/evening I have to re-boot my router to get internet access. Netgear N300 ADSL2+ modem router Model DGN 2200 (had about a year), Windows 7 64bit Home premium Laptop connected wirelessly, Windows 7 64Bit Home Premium desktop connected by LAN cable. ISP BT Internet. Until recently this set up has been working OK with occasional loss of interent access and need to re-boot router. The internet light has been showing red on those occasions. Over the last two weeks I have found that when I turn one of computers on although all lights on router are green I have no internet access. I have to re-boot, then all is OK until the next day when I have to re-boot again. My phone line appears OK with no noise on line, no reported problems on BT broadband staus. The thing that puzzles me is that the lights are all green on the router yet my networking icon on the pc shows an exclammation mark and 'no internet access' and I do not have access to net.The wireless connection is OK with excellent strength.
View 7 Replies
View Related
Oct 16, 2012
Region : Egypt
Model : TD-W8961ND
Hardware Version : V3
Firmware Version :
ISP :
my router is placed in my home. i want to access to it with IE from my office.but no luck.also i try to ping the WAN ip address of the router.
View 2 Replies
View Related
Jan 7, 2012
I would like to know if the Linksys X2000 ADSL2+ modem router will work with my IPTV service.
View 3 Replies
View Related
Jan 2, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
View 2 Replies
View Related
Oct 12, 2012
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
View 6 Replies
View Related
Apr 9, 2013
Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
View 1 Replies
View Related
Oct 18, 2011
I have a CDMA compatible modem which connects to my Desktop PC via USB.it works fine, but I'd like to share my internet connection with another Laptop, Wirelessly via a Router. The router connects to my Pc via Lan cable. I activated Internet Connection Sharing in the properties of my modem and connected it to the Internet.I hoped my Router would detect an Internet connection on My network and would enable internet connectivity on My wireless AP on the Router. But it didnt. is that windows refelcts "internet access" on both the actual Wireless network on my Router ("49 network") , and on both the Physical Connection to my pc via the Ethernet port ("3G Router") my laptop connects to the router, but without access to the internet, and I keep getting an 'unable to resolve host' message in my Browser. Suspecting my Router of somehow causing the problem I also tried setting up an Ad hoc network instead (using my wlan card to interface with the Laptop directly). They connect fine, and my Printers and other shared resources all appear, but the wireless range between them is like bluetooth compared to the great range of my router.& I still cant manage to share an Internet connection between the two machines!
View 9 Replies
View Related
Dec 11, 2012
how to properly configure 2 different hardware devices to extend the current wifi signal of my home network.I'm using a Motorola SBG6580 DOCSIS 3.0 cable modem as my primary access point (AP) and a Netgear N300 DGN2200v1 ADSL2+ modem router which will function "behind" the SBG6580 in repeater mode. I previously had DSL for my internet connectivity but recently switched to broadband cable for faster speeds.Due to the layout of my home, I cannot physically connect the Netgear router to the Motorola modem via ethernet cable and need both devices to communicate wirelessly. I have already done extensive reading on this subject and best practices suggest that, whenever possible, both units should be the same brand/manufacturer. The Netgear appliance does have the capability of being configured as a repeater so if I don't have to buy a "network extender" that would be my preference.I understand that both units must be configured to have the same SSID, subnet, wireless channel and security encryption. In repeater mode the Netgear router can't be configured to use WPA2-PSK so I need to use WEP instead.
View 1 Replies
View Related
Sep 9, 2011
Is there a way to put the .EXE program in the start connection in Wireless Router WRT54G ?
or a .ASPX page when start the connection ? I want to do it:
I want to control the time that the users used the internet in the hotel. The users had the login and the password which one. And I want stop the connection when the user get the time.
View 1 Replies
View Related
Dec 12, 2011
My main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies
View Related
Oct 12, 2011
I recently needed a new router from my internet provider. They came to my home and set up Westell 7500 modem router. My home computer brings up internet with no problems or delays. Unfortunately, my wireless laptop won't recognize any network.I plugged it in using the ethernet cord directly to laptop and modem and still no internet. I'm frustrated, I use my laptop all the time and without the internet it's worthless.
View 1 Replies
View Related
Dec 29, 2011
I have a broadband connection through a TV cable connection to a ISP provided modem/wireless box. I have a wireless network set up already from this box. I wanted to extend the wireless network to a hard to reach area so i bought a seperate router (d-Link DIR-615 revE3).
I connected one of the 4 LAN outputs from the modem to the router's "Internet" input. Windows 7 detected the new router's wireless network and guided me through setting up a name and password for it. However there is actualy no internet access on this network even though it's directly connected to the modem.I was thinking that i wanted to just extend the original wireless network but a new network is fine if only it would use the internet from its LAN connection... a desktop computer has connected from the same LAN output of the modem without any security and been able to access the internet from it.
View 3 Replies
View Related
Jan 18, 2012
Just purchased a Belkin N600 DB N+ Wireless Router because the wireless on my Actiontec PK5000 really isn't so great. When I hook up the router to my modem and after running the install CD I couldn't get connected to the internet. So I looked at my modem and noticed the light where I had plugged in my router VIA ethernet wasn't lit up like the rest of my ethernet ports even after switching them around.
View 6 Replies
View Related
Aug 26, 2012
The detected problem is the connection between my access point, router, or cable modem and the Internet is broken.The network gateway is accessible, but Windows couldn't receive network traffic from the Internet.All other devices (iPad, Xbox, android phone) have no problem connecting to the Internet.Desktop is the only one experiencing the connection issue.
View 1 Replies
View Related
Jan 31, 2012
My laptop died last week and have been using my husbands, which I hate! We had some issues with computer freezing on some webpages or after being on webpages for awhile (like facebook). Yesterday it froze and I could not get it back on. When he got home he did scan disk (which I also did) and got it working after going into safe mode and doing system restore. He said an update had gotten through and messed things up. Anyhow, after he was on it a few hours last night, we lost connection. I figured the crazy weather was the culprit but it has been off all day. Our router is working and connecting but the adapter is not. Also our home phone says there is no line. We have unplugged everything several times, checked to make sure everything is in the right spots, I have even reset the router and rebooted the adapter. I uninstalled and restalled the adapter also. It is now telling me that "the connection between your access point, router, or cable modem and the Internet is broken". The only lights I have on the adapter are power, battery, DS and now the US light is blinking. The online and link lights are not on.
View 3 Replies
View Related
Jan 19, 2013
Immediately after a power outage, my internet connection predictably drops after a set period of time or usage. It is either after about 30 min or 5-15 mins of watching Netflix. I have a modem hooked up to a wireless router and use the network on my iPhone, laptop and Roku. Since the problem, I have dropped to just having my laptop connected but this has not worked. The wireless network will disappear after the 5 - 20 mins, the light on the modem and router will show no internet (all other lights are normal). Internet connection will be reestablished if I either unplug both the modem and the router (not just one or the other) OR if I unplug the ethernet line from the modem to the router and plug it directly into my laptop (the internet light on the modem will go from "off" to "on"). Despite internet connection working from transferring from the router to the laptop if I connect it back to the router, the internet lights goes off again (resolves upon unplugging and plugging modem and router back in). The internet has not yet dropped when it is physically plugged into my laptop.
I have tried the following:
-Powercycling (temp fix until it crashes again)
-Plugging into a different outlet (I cannot connect it to a different phone line, only have 1 with DSL. Also, I do not have phone service or cable, just internet via DSL)
-Resetting modem
-Resetting 2 different routers
-Calling ISP, their test of the modem was inconclusive
Again, my wifi does not see my network whenever the internet is dropped or the ethernet cord is unplugged from the modem. The outlets I have it plugged into has some type of electrical issue, two electrical devices have shorted out in the room they are in. I do not think this issue is electrical, everything seems to have constant power (unless the power outage shorted out something in the modem). Below are some details of my modem and router. I will provide any additional info requested. I will gladly buy a new modem but I want to see if it can be fixed first.
My modem: Westell
WireSpeed Dual Connect
Model: A90-210030-04
DSL Statistics
Line State: Up
Modulation: G.DMT-Mode
Data Path: Interleaved
[code].....
Router: Linksys E2000 Internet Connection Type: Automatic Config - DHCP (I tried PPPoE and it never got a valid IP address from my ISP)
View 3 Replies
View Related
Aug 1, 2011
Earlier today I attempted to change the setting on my Westell 6100 modem such that it would simply bridge the connection to my Linksys WRT54GS router, basically involving setting the router to bridge only and turning DHCP off. Now I no longer get an internet connection through my router when previously the connection had worked perfectly fine before. I following the steps of cloning the MAC address to the router and have done the proper resetting steps (computer, them router, then modem) but I simply can't get an internet connection through my router. The process to set up simple bridging from the modem what supposed to end up with the internet light no longer turning on but the light turned back on following one of the resets.
Currently, I can connect to the internet through the modem just fine but I get nothing when I include the router. I'm not sure if there are some other settings I'm supposed to be changing as I can't seem to find anything past what I've already done when researching online. At this point I would just be happy reverting the settings I've changed but I don't know how to access the modem now that DHCP is off.Basically, I'd prefer to be able to get the router working with these new settings but if that proves too difficult (as I've heard it can be when trying to get Westell modems to work with Linksys routers) I'd like to learn how to access the modem and change the settings back to what they were (preferably in as simple terms as possible as I don't particularly understand what a lot of these settings/configurations do).(And a bit of an aside, but I had attempted to do this modem bridging to "fix" perceived internet speed problems. I've been averaging around 300Kbps download rates ever since I've had this internet connection from Verizon when the supposed download rates should be between 1MB and 1.3MB. Doing this modem bridging had been reported to fix some modem/router conflicts and improved connection speeds for some.)
View 5 Replies
View Related
Jul 6, 2011
I plan on moving to a new internet service provider within a few weeks time, and I have a question.I'm going with TekSavvy, and they have a DSL plan which is quite worth it, and I'm in need of a modem when I make the switch. I think I made up my mind on which modem I want, but I just need to know.. can I use ADSL2+ on the DSL service I am going to get?If you need to know what modem I'm going for, I'm going with "TP-LINK TD-W8960N, 300Mbps Wireless N ADSL2+ Modem Router"
View 1 Replies
View Related
Jul 7, 2012
The power is working, i went on device manager and there isn't any yellow flag next to it , when i clicked on the dlink software , it said wireless adapter not found.How do i make it recognised
View 2 Replies
View Related
Aug 12, 2012
My WRT54G2 v1 does not automatically connect to the internet on computer start-up. The computer will say "Connected, No Internet Access" In order to fix it I have to unplug the router and then plug it back in. This happens to any computer that tries to get online from a cold start-up. The router must always be unplugged, then plugged back in, then it will have internet access (and will generally maintain it throughout the session and even if the computer is restarted, i.e. warm boot). I have downloaded the latest firmware uprade.
View 9 Replies
View Related
Feb 24, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
I am having difficulty setting up the W8968 to replace the router given by TM for the Unifi connection.I tried updating the firmware of the modem router and used quick setup to configure the device as a wireless router using PPPoE, but still couldn't connect to the internet using the WAN port.I noticed there was a guide for TD-W8960N to set up TM Unifi but the web interface is too different from the W8968 interface.
View 1 Replies
View Related
