Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
Region : Canada
Model : TD-W8960N
Hardware Version : V1
Firmware Version :
ISP : Bell Canada
Can I use TD-W8960N an additional router with my ISP bell router. Will it increase my speed and range of internet in my home.
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
ISP : Centurylink
I am replacing my qwest/centurylink actiontec q1000 with the td-w8960n. I have run all the different setups, with the different settings that I have found on the net but to no avail. The one thing I have noticed is that the light for the asdl on the td-w8960n does not come on, but yet when I plug it back into the actiontec it sees it and the internet works. Any reason why the td-w8960n is not recognizing the active dsl line?
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
Region : United Kingdom
Model : TD-W8960N
Hardware Version : V1
Firmware Version :
ISP : Unforced 9
I am struggling to get my blackberry Z10 to connect to the router.
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V4
Firmware Version :
ISP : Be Internet
I have a router supplied by my ISP which is effectively locked down, the wireless on that router give me a massive 35 Mbps (yes i know... awesome) so I wanted to get something that would allow me to stream movies wirelessly in the house. The setup I had before was Thompson DSL router downstairs (ISP router) running the DSL connection and Wireless, a TP-Link 200Mbps Power over Ethernet connecting upstairs to a Netgear ADSL Wireless router (somewhat flaky device). This router had DHCP disabled and a static IP address, I had configured wireless with the same SSID, password and channel as the ISP router and they were all happy and everything was working (most of the time except when the netgear would crash or the 35MB wifi was too slow to achieve what I wanted).
What I would like to do is this... ISP router downstairs with wifi disabled so it just handles DHCP and DSL connection, router upstairs (New TP-Link) running new WiFi, DHCP disabled (static IP address for Router) but connected to router downstairs through TP-Link Power over Ethernet.
I was hoping it was as simple as the Netgear router where disabling DHCP was enough for it to see the other router and just work but it isn't doing that
I can ping the ISP router but cannot get to the internet,
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband
Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.
i have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies View RelatedModel : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
URL Filter not working
Region : Australia
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
Cannot get the URL filter to work Just upgraded to latest Firmware but that didn't work?
URL List Type: Deny Allow Disable
Address Port Remove
[URL]
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
According to the manual, when I go to edit my WAN connection, I should be able to enable/disable the SPI firewall. However, on my firmware I get no such option. My SPI firewall is always enabled.
I would like to be able to completely disable it when I'm testing so that I can ensure the firewall is not interfering with my tests.
Region : Others
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
Region : Sweden
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
opening of some ports 25565 for minecraft so i can host games. i have try so solve this by my self but with zero progress. did enter the advanced setup and then i pressed on the NAT category and then i pressed on the ADD button and enter the following" [URL] and then i used a port checker to look if it worked but did not work?
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : AT&T
Everything seems to work fine except that there is no Wireless option in the menu. I updated the firmware and reset to factory defaults, but the wireless option still does not appear in the menu.
Region : UnitedStates
Model : TD-W8968
Hardware Version : V4
Firmware Version : 1.1.1 Build 120912 Rel.67406
ISP : centurylink
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 1.1.1 Build 120912 Rel.67406
ISP : centurylink
First a bit of background. At the end of December, my centurylink modem finally had enough problems with disconnects(was 6 or 7 years old), and Centurylink sent out a new router/modem. The new modem/router, a Zyxel, worked great, and all was good in my house hold. Then I got the bill and found out that unlike the previous modem they had sent me, this one I was paying a lease payment for. At which point I returned the Zyxel which gave us the best service we'd ever had, and bought this TD-W8960N. The reviews were glowing, setup was easy, but we started rather quickly to have disconnects. A call was made to Centurylink and they confirmed service was working, and since the modem/router was not theirs, referred us back to you. I called and after considerable time on the phone, all I was basically told to do was a hard reset to the modem. When the unit finished booting back up, internet was restored. Of course it was restored everytime we reset it for a while. At that point I was told that since the unit was working, that there was nothing left to be done. Since that time, it has disconnected us from time to time, and then in the last 2 days, sometimes it won't stay connected for more than a couple of minutes. My wife is very unhappy-she is a gamer, and a disconnecting internet is very very bad for an online gamer.
It seems that the further it gets away from a hard reset,the more it disconnects. After 6 soft resets (unplugging) today, I had to do another hard reset to get back on to register here and post this message. Is this a known problem for this unit? Is there a fix for this unit? Or, do I just need to return it to Newegg and try another manufacturer?
Again, the "leased" Zyxel gave us no problems for the month or so that we used it.
Region : United Kingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP : ADSL24
How to successfully get VPN passthrough working with the W8960N?
I have the W8960N providing internet to local device. I want to setup a second router, TP-Link 1043ND with WW-DRT and PPTP set up to provide a separate access point for PPTP tunnelling to VPN servers outside of the UK. HideMyAss are providing VPN servers I wish to connect to.
I have followed instruction to set up both routers but would like to know if I am missing something.
First router 192.168.1.1 is basically untouched but with ports under NAT added: ports 1723 and 47 for my second router at local IP 192.168.1.111
Second router is set up according to [URL].
I know VPN work via just my first router. I can tunnel through using an Android tablet and connect to any HMA VPN server without changing anything on the 8960N.
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 110620
ISP : BE Broadband
I have an issue sending pictures via iMessage on iOS.
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 2.1 v000c.0 Build 130415 Rel.34164n
ISP : plusnet
I have setup 2 vpn tunnels from my TD-W8970 to places that use TD-8960N (Firmware Version: 1.4.0 Build 110921 Rel.17774n Hardware Version: TD-W8960N v3 0x00000002 )and I can ping and connect to any ip used at their end but they can only ping 192.168.1.1 which is my router and not 192.168.1.104 which is my Synology DS212J that they need to access.
Both tunnels are similarly configured:
Tunnel 1 on my TD-W8970
IPSec Connection Name: Tony1
Remote IPSec Gateway Address(URL): 89.240.xx.xx
Tunnel access from local IP addresses: Subnet
IP Address for VPN: 192.168.1.0
IP Subnetmask:255.255.255.0
[URL]
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.54317n
ISP : century link
How do I test my routers ddns? My computer went down. So, my adsl ip address changed. I caused the modem/router to reboot. But the new ip wasn't sent to the Host (dyndns.org). I had to update my ip manually on [URL].
Region : Peru
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build111108 Rel.40398n
ISP : Telefonica
I purchased this TD-W8960N cause I thought it was a powerful beast, but it is not unless mine it is defective. On my mobile phone it shows -25 to -30 dBm at less than 10 inches away from the router antennas. In some places at home my phone disconnects when the signal drops below -70bm, however my laptop it is always connected because of the better antenna.
That's fine BUT, I installed my old Linksys WRT54G and the phone shows -3dB at the same distance from the antennas. Or is it that I overvalued the TP-LINK?Does anyone have compared signals with other routers. Should I assume that mi router is defective? Any trick to squeeze more power other than replacing antennas?
Region : Egypt
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : STE
In the past everything was working fine (had same computer connected wireless + wire) never had this disconnection. Now, I have a laptop connected using wireless & desktop wired but this disconnection is becoming so irritating. It is not only that I lose the internet connection, I lose the DSL like (as if the modem is turned off then on) and all my files over the LAN are either lost during transmission or something else.
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : talk talk
All working well except Net Radio on my Yamaha AV amp. When attempting to listen message receive 'access error' never had this with Linksys router. The amp has been setup with the internal lan gateway address and used dns from talk talk detail. IP has a static IP address . I have tried placing amp in dmz address which didn't work also tried port forwarding 8000 - 8001 which someone said was the port used for yam net radio. none of this works. Never had to do any of this before simply used local gateway address and local internal dns from the old router and always worked with tp - link just cannot get it to go.
Tried lots of variation gateway and dns addresses none which worked...
Region : Australia
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N_V4_130205_Beta
ISP : TPG
I have an Optus Home Zone (mobile cell tower) that requires ports open.
Port
123 UDP
500 UDP
4500 UDP
I have assigned the Home Zone a Static IP outside the DHCP range and set the above Ports on the NAT, Virtual servers to that IP address.
I have used nmap to scan the ports and it provides open/filtered status for all of them.
Here is the kicker for me, i use a DGN3500 netgear (which keeps dropping WiFi hence its replacement) and enter the ports and it works straight away. Un plug and put the Tp-Link and nothing.
I use Eset Smart Security, could that be the problem?
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP : Snap
I just bought a v3 TD-W8960N and I'm trying to see what is the latest firmware available?On the modem it came with 1.4.0 Build 111130 Rel.56405n.When I look on the website the listed latest version is w8960nv1_un_1_4_0_111108R40398.up (that is the file inside the zip package/link TD-W8960N_V1_V3_111108)Which is the newer version? The revision number on the firmware that came installed kind of looks like it is actually newer. But if it is newer, why is not available for download from TP-Link?
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
Region : Argentina
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
Region : Australia
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 110620 Rel.52053n
ISP : Amnet
I want to setup this modem wirelessly such that:
- Wireless User A has full unrestricted wireless access (to Internet and all other services) and
- Wireless User B has no internet access but access to file sharing and related services.
Can this be done and how can it be done?
Region : Ireland
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N
ISP : Vodafone Ireland
I am having a rather annoying problem. I run a small hotel (just 3 floors) and my modem gives a strong enough signal to provide wireless access to everybody in the house however I'm finding that a lot of people, whilst they can connect to the modem, cannot browse online. Connection just times out when they open their browsers.Recently a guest gave me his laptop and asked me if I could do anything with it. I'm by no means an expert when it comes to this kind of thing so I chanced my arm by putting his MAC address into the CP's Wireless/MAC Filter page. He connected immediately and was able to go online much to my relief.
Thing is, I don't want to have to do this for every guest that comes through my door! Is there any way everybody who has a laptop can connect without me manually entering their MAC addresses? MAC restrict mode is set to 'disabled' but I thought that would allow everybody unrestricted access?
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : DEMON
I'm using parental controls to block all devices in the house from using tumblr. I cannot do this at a device by device level as it is being used on iphones/androids, laptops and desktops.Unfortunately, the way that tumblr works is that it use many URLs for the different pages people set up so it is not just a case of blocking url... - so I'm struggling to work out if I can do this via URL blocking on the router settings. How to do this at router level.
I bought my dad a Netgear N150 DGN1000 Wireless ADSL Router to replace his D-link router which kept dropping the wireless signal. I have established a wired connection and my ipad, iphone and his old laptop connect wirelessy to it without any problems but I just cannot work out why his laptop won't connect to the internet.It recognises the wireless signal and it says its connected and that the signal is excellent but when I try to go on the web or check emails it just won't work.I've tried deleting all his wireless networks and starting from scratch but don't know what else to tryHis PC is running windows Vista
View 9 Replies View RelatedRegion : Italy
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 67406
ISP :
I have problem on router td-w8960n v4 internet speed download is limited a 4 mb in device android e ios wifi connected for test i use application speedtest.net on ipad 3 and samsung galaxy s
I own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 Replies View RelatedRegion : Brazil
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Telemar Oi Velox
Very weird situation... can't get full speed with the TD-W8968 with my DSL link..
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Telecom
Below you point out my attenuation values detected on the modem in question:
Line Status:Connected
DSL Modulation Type:ADSL_2plus
Annex Type:Annex A
UpstreamDownstream
Current Rate (Kbps)4768124
Max Rate (Kbps)104811512
SNR Margin (dB)28.412.2
Line Attenuation (dB)17.233.4
Errors (Pkts) 0 0
The part adsl should be revised as the highlighted value and too discordant from the value taken on the same line as route draytek 2800 with attenuation of 24.5 db snr to 16dB, I'd like to find a job in the next firmware dedicated all'ottimizzare driver adsl modem so is worse than 6 years old
Region : India
Model : TD-W8151N
Hardware Version : Not Clear
Firmware Version :
ISP : MTNL
my ADSL light doesn't get on during my afternoon hours...after so many try too it get switch on after somewhat 5-6pm...
I have a TP-Link TD-W8960N Wireless Router. I would like to know what the I.P. addresses of connected clients are (both those connected wirelessly & those connected by Ethernet cable). There are about 6 computers in my network, some have dynamic and others have static I.P. addresses.I am finding it difficult to navigate the router,on which menus get me to the information that I am interested in
View 1 Replies View Related
