Region : India
Model : TD-W8151N
Hardware Version : Not Clear
Firmware Version :
ISP : MTNL
my ADSL light doesn't get on during my afternoon hours...after so many try too it get switch on after somewhat 5-6pm...
Region : India
Model : TD-W8151N
Hardware Version : V3
Firmware Version : 120530
ISP : BSNL
Net is working smoothly from LAN, but no success on wifi. Over wi-fi, I can connect to router but cannot access net.
Region : Vietnam
Model : TD-W8151N
Hardware Version : V1
Firmware Version :
ISP :
I'm using a Tp-Link's Product (TD-W8151N). But now, i want to using TL-Wr740N repeat the Wifi from TD-W8151N. How can i do that?
Region : Indonesia
Model : TD-W8151N
Hardware Version : V3
Firmware Version :
ISP :
Recently I bought TD-W8151N wireless adsl router, I have one desktop computer that connected to TD-W8151N via ethernet and wirelessly to one laptop, IP Addr: 192.168.1.4, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : desktop (LAN connection IP Addr: 192.168.1.3, Subnet 255.255.255.0 and Gateway: 192.168.1.1 : laptop (wireless connection) but I can't ping each other and also can't access the share folders between them., both computers can access internet. Is there anything I missed the configuration setting of the router? Before I use wireless, I connected this 2 computers using cross-type utp cable, and working good.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I have an unused TD-W8151N. I also have a smart TV that requires a wired connection, with no way of getting a wire to it.
Can I configure my spare TD-W8151N as a client of the existing WiFi network and connect the TV in to the TD-W8151N with a cable?
Region : Egypt
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : STE
In the past everything was working fine (had same computer connected wireless + wire) never had this disconnection. Now, I have a laptop connected using wireless & desktop wired but this disconnection is becoming so irritating. It is not only that I lose the internet connection, I lose the DSL like (as if the modem is turned off then on) and all my files over the LAN are either lost during transmission or something else.
Region : Brazil
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Telemar Oi Velox
Very weird situation... can't get full speed with the TD-W8968 with my DSL link..
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Telecom
Below you point out my attenuation values detected on the modem in question:
Line Status:Connected
DSL Modulation Type:ADSL_2plus
Annex Type:Annex A
UpstreamDownstream
Current Rate (Kbps)4768124
Max Rate (Kbps)104811512
SNR Margin (dB)28.412.2
Line Attenuation (dB)17.233.4
Errors (Pkts) 0 0
The part adsl should be revised as the highlighted value and too discordant from the value taken on the same line as route draytek 2800 with attenuation of 24.5 db snr to 16dB, I'd like to find a job in the next firmware dedicated all'ottimizzare driver adsl modem so is worse than 6 years old
Region : India
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : S/N: 12B79605315
ISP : BSNL Data One
I had Purchased a brand new TP-Link WifI Modem Router TD-W8961ND with S/N : 12CB5200872 from [URL] and it got delivered few days back. When I am trying to connect it to the internet the modem is not getting connected nor configured. The Power button light, ADSL Light and internet light are continuously blinking and nothing is getting steady. The modem is appearing to be a damaged piece of modem and it is very unfortunate that we have got a modem from flipkart in an unserviceable condition. It came with a warranty of 03 years and I wanted a replacement so that I can use the modem for connecting internet.
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
ISP : Centurylink
I am replacing my qwest/centurylink actiontec q1000 with the td-w8960n. I have run all the different setups, with the different settings that I have found on the net but to no avail. The one thing I have noticed is that the light for the asdl on the td-w8960n does not come on, but yet when I plug it back into the actiontec it sees it and the internet works. Any reason why the td-w8960n is not recognizing the active dsl line?
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
Find list of all the MAC address of the devices connected to the router?
View 2 Replies View RelatedI have a Netgear N150 Adsl router with Orange and the internet light is constantly red and i have no internet connection i can connect to the router but have no ip address.
View 1 Replies View RelatedMy ADSL light switches off randomly during downloading a 100mb file. I just cannot complete the download. This has been happening ever since I switched my router to a wireless iBall Baton 150M.
View 9 Replies View RelatedRegion : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies View RelatedRegion : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
I just bought the wireless-g range expander from a computer parts store.... its not brand new, and i don't have the cd. It is picking up the wireless signal and my laptop sees that it is excellent signal strength but it won't connect to it and the "Link" light is red
View 1 Replies View RelatedI've had major issues connecting to the Internet in the last couple days. I can't think of anything specific that was changed. The lights on the front:
Power light - steady on.
Circle/triangle light - flashes at approx once per second.
4-circle light - intermittent quick flashes (but mostly on).
Wireless light - COMES ON FOR THREE SECONDS EVERY FIFTEEN SECONDS!
All the lights are green.
Dir-655
Hardware A1/a2
Firmware 1.35NA
I tried turning SEP off. No luck. To note, the Internet works when I hard wire a computer through the dir-655.
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
[code]...
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
According to inSSIDer the router seems to be using two wifi channels (10+6) and inSSIDer is recommending to move to a standard channel (1,6,11).
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband
Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version :
ISP :
problem with filtering
Region : Syria
Model : TD-W8901G
ver 6.0
54Mbps wireless G ADSL2+:
I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."
I have a WPC54G ver. 2 adapter I am trying to get to work on a thinkpad T22 running W2kPRO with all the SPs and updates installed. The power light comes on, but the link light does not. I am using a Linksys WRT54GS wireless router. The monitor icon shows in the taskbar and when I open it, it says the adapter is inactive. I have tried several time to download and install the driver for the Linksys site. It seems to install OK, but when I go back and check the Drivers tab to verify that the driver version has changed to 3.20.21.0, it is still version 6.0.0.18.
View 4 Replies View RelatedRegion : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
I have had a Dlink dir 615 for some time now and always had a few issues, but nothing a reboot of the router couldn't solve. This time the problem is persisting, though. The wireless signal keeps blinking and on my laptop it says No internet connection. I've rebooted the router, restored the router, rebooted the modem, and nothing seems to work.
View 1 Replies View RelatedI use a wired network connection to my neighbours Vodafone Modem (We share his monthly cost). I also have a TP-LINK 54M Wireless ADSL2+ Router from a previous broadband contract with a landline phone company. Is it possible to reset and configure the TP-LINK Router to act as a relay unit, connected to the network cable, so I can then use my laptop elsewhere in the house?
View 3 Replies View RelatedRegion : Spain
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120524 Rel.05221
ISP :
linksys1.jpg
I have wifi at home this link installed.
192.168.1.1 is a TD-W8961ND
192.168.1.4 is a linksys wrtt54gl
And I have two problems.
1) I can not see any desktops in my local net, and with old router I could see all, for example (diskstation, dm800, etc...) In my macbook air I can not see my NAS Synology and with old router I do.
2) All PCs that are conected to 192.168.1.4 have not IP. and DHCP in TD-W8961ND is activated.
Region : Argentina
Model : TD-W8968
Hardware Version : V1
Region : UnitedKingdom
Firmware Version : 101029
ISP : TalkTalk
I have version 1.1 and d/l'd firmware 111125. The upgrade ran successfully to 100% and then I got the login screen again. However after checking, then restarting to factory default the version displayed was still the old one
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
URL Filter not working
Region : Australia
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
Cannot get the URL filter to work Just upgraded to latest Firmware but that didn't work?
URL List Type: Deny Allow Disable
Address Port Remove
[URL]