D-Link DIR-655 :: Wireless Light Flashes Every 15 Seconds?
May 5, 2013
I've had major issues connecting to the Internet in the last couple days. I can't think of anything specific that was changed. The lights on the front:
Power light - steady on.
Circle/triangle light - flashes at approx once per second.
4-circle light - intermittent quick flashes (but mostly on).
Wireless light - COMES ON FOR THREE SECONDS EVERY FIFTEEN SECONDS!
All the lights are green.
Dir-655
Hardware A1/a2
Firmware 1.35NA
I tried turning SEP off. No luck. To note, the Internet works when I hard wire a computer through the dir-655.
View 1 Replies
ADVERTISEMENT
Apr 3, 2011
My internet light flashes at times yellow.Some times i lose internet connection .I have never had this problem with my linksys router.
View 3 Replies
View Related
Apr 11, 2011
Have noticed this in almost a regular pattern. About every 3 seconds the internet light whick is blue most of the time will ocassionally flash white then maybe yellow. Does not appear to interupt internet access yet last only a second (at the longest),so don't know if I would notice. Am connected to DSL modem and see no change it its indicator lights,(traffic, collision, lan), when it occurs on the DIR-655. Have three PC's and a network (LAN) printer as well as wireless enabled. BTW is does not matter if wireless is active. What do the different colors mean ?? Blue = Connected White = Yellow =
View 3 Replies
View Related
May 22, 2013
Belkin n wireless router model number F5D8236 v1! my modem is showing an internet connection but my router "modem" light is flashing orange and my internet light doesn't even come on. we are not sure but we believe this became a problem last night after my daughter connected her new lap top to the wireless connection.
View 1 Replies
View Related
Jul 23, 2012
I have Qwest DSL 7MB internet with a motorola 3347 Qwest model modem and for some reason throughout the day sometimes fewer than than others my internet light will just go red for about 45 seconds up to 2 to 3 minutes them it starts flashing green again? I called them multiple times but they just say maybe its the modem. Is there any test I can do to see? I upgraded the firmware to the newest one to see if that would work but no luck.
View 1 Replies
View Related
Jan 5, 2013
Region : Argentina
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version : 3.12.4 Build 100910 Rel.57694n
I did a hard reset and after that, when i power on the router, it works for aprox. 15 seconds, so i can access the interface at 192.168.1.1, but after those 15 seconds it doesnt respond. The lights are on as if it was perfect, but cant go on admins interface and ping doesnt work either. I did several resets, did the 30/30/30, and clicked on reset to factory defaults on those 15 seconds but nothing happens.
View 3 Replies
View Related
Jan 21, 2013
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
My router is not working and only all lights are flashing everytime after interval of 2 seconds.
View 1 Replies
View Related
Jul 22, 2011
I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies
View Related
Aug 15, 2011
I just bought the wireless-g range expander from a computer parts store.... its not brand new, and i don't have the cd. It is picking up the wireless signal and my laptop sees that it is excellent signal strength but it won't connect to it and the "Link" light is red
View 1 Replies
View Related
Mar 3, 2013
I have a WPC54G ver. 2 adapter I am trying to get to work on a thinkpad T22 running W2kPRO with all the SPs and updates installed. The power light comes on, but the link light does not. I am using a Linksys WRT54GS wireless router. The monitor icon shows in the taskbar and when I open it, it says the adapter is inactive. I have tried several time to download and install the driver for the Linksys site. It seems to install OK, but when I go back and check the Drivers tab to verify that the driver version has changed to 3.20.21.0, it is still version 6.0.0.18.
View 4 Replies
View Related
Mar 23, 2013
Region : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
View 2 Replies
View Related
Jan 28, 2011
I have had a Dlink dir 615 for some time now and always had a few issues, but nothing a reboot of the router couldn't solve. This time the problem is persisting, though. The wireless signal keeps blinking and on my laptop it says No internet connection. I've rebooted the router, restored the router, rebooted the modem, and nothing seems to work.
View 1 Replies
View Related
Aug 11, 2011
I have 3 1142N AP's. I plugged them in one at a time here at my desk and they work fine. When I take them upstairs and install them only one of them works. I can move the working one to the other locations and it still works. The LED flashes continously green on the other two.
View 4 Replies
View Related
Mar 3, 2013
Region : Egypt
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : STE
In the past everything was working fine (had same computer connected wireless + wire) never had this disconnection. Now, I have a laptop connected using wireless & desktop wired but this disconnection is becoming so irritating. It is not only that I lose the internet connection, I lose the DSL like (as if the modem is turned off then on) and all my files over the LAN are either lost during transmission or something else.
View 1 Replies
View Related
Feb 13, 2012
I accidentally pressed the front panel button labeled "Cisco Systems" on my WRT54GL wireless router. The button turned to a flashing white which I understand means that it entered SecureEasySetup mode. I then power cycled the router and the front panel button turned back to solid orange. However, now the "WLAN" lamp flashes a lot more often than before even when there are no wireless clients connected. It doesn't seem to be affecting connectivity or performance of my Ethernet connected devices or wireless connected devices. I re-entered my SSID and security key. That didn't curtail the increased flashing of the WLAN lamp. I also tried pressing the front panel button for 5 seconds. This only cleared my wireless settings.
View 2 Replies
View Related
Jan 25, 2013
Region : India
Model : TD-W8151N
Hardware Version : Not Clear
Firmware Version :
ISP : MTNL
my ADSL light doesn't get on during my afternoon hours...after so many try too it get switch on after somewhat 5-6pm...
View 1 Replies
View Related
Mar 25, 2013
Region : Others
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.11.3 Build 100408
ISP : Telekom
the SYS light, keeps blinking is that normal?
View 2 Replies
View Related
Mar 4, 2013
I have two LAP1041 with WLC2504 everything works fine. But since yesterday when it boots up it flashes green, then solid green, then after about 10 seconds the green LED turns off, however the LAP is still working fine, Why is that? If I put my eyeball up close to the LED I see dim red inside the LED plastic cover.
View 3 Replies
View Related
Oct 24, 2011
My router is stuck in a loop. At connection time of 1min39, the dhcp release button presses donw by itself. It does that continually, non-stop. It won't show me as a dhcp client yet i have internet access.
View 1 Replies
View Related
Nov 20, 2011
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
View 7 Replies
View Related
Oct 19, 2011
So I just noticed on my Cable modem the link light is blinking orange, per Motorola if its blinking orange - Computer is connected via a 10 mbps or 100 mbps Ethernet port.
On the Linksys E4200 status page it says
Internet Port Speed:
Internet 10/100 mbps
Local Port Speed Port 1 - 1Gbps
Maybe I just noticed this with this router, but I'm pretty sure this didn't start happening until I updated to 1.0.03.
Previously the link light was blue indicating a 1Gbps connection.
View 4 Replies
View Related
Jun 19, 2011
I have a D link 655 wireless router and my magic jack calls end after 15 seconds.
View 2 Replies
View Related
Mar 1, 2013
I have a DIR-825 with 2.60VT firmware (rented from Videotron).
Even though the manual says the stateful firewall should have a timeout on connections of 240 seconds or 7800 seconds, all of my connections start at a mere 120 seconds. I'm having trouble with IMAP IDLE pushing e-mails because the connections timeout so quickly (before any stay alive can be sent). A connection to the e-mail server gets opened on 143 (Videotron) or 993 (encrypted - google, e.g.), and I see the connection on the Internet Sessions page, the timeout starts at 120. When it hits 0, the connection is no longer displayed (it is not renewed), and the IMAP IDLE ****s out because the server can't find the client (i.e. the connection has been closed). But it's not just on those ports or servers. ALL of my TCP sessions begin at a mere 120 seconds! Even for a home router, isn't this way too low?
confirm that their DIR-825, on the Internet Sessions page, shows initial timeout values of greater than 120 for a TCP connection? I would love to see a picture of that screen showing higher values. Does it start at 240? Do you ever see a connection start at a timeout of 7800?
I see no way of changing the timeout value. Is it possible to force connections on certain ports to begin at a higher timeout value?
View 5 Replies
View Related
May 10, 2013
Region : India
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : S/N: 12B79605315
ISP : BSNL Data One
I had Purchased a brand new TP-Link WifI Modem Router TD-W8961ND with S/N : 12CB5200872 from [URL] and it got delivered few days back. When I am trying to connect it to the internet the modem is not getting connected nor configured. The Power button light, ADSL Light and internet light are continuously blinking and nothing is getting steady. The modem is appearing to be a damaged piece of modem and it is very unfortunate that we have got a modem from flipkart in an unserviceable condition. It came with a warranty of 03 years and I wanted a replacement so that I can use the modem for connecting internet.
View 1 Replies
View Related
Feb 18, 2013
Region : Canada
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3.14.4
Recently in the morning the router will have lost ability to connect to internet <internet light is on> and I cannot access the router page <sys light solid> from either wired or wireless connections. Why is this and will it be solved if I upgrade firmware?
View 2 Replies
View Related
Jan 27, 2013
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
ISP : Centurylink
I am replacing my qwest/centurylink actiontec q1000 with the td-w8960n. I have run all the different setups, with the different settings that I have found on the net but to no avail. The one thing I have noticed is that the light for the asdl on the td-w8960n does not come on, but yet when I plug it back into the actiontec it sees it and the internet works. Any reason why the td-w8960n is not recognizing the active dsl line?
View 6 Replies
View Related
Oct 27, 2012
I got 3 new TP-Link WA901ND PoE access points for a wireless network I manage. Right now I'm using the stock injectors that came with them because I need to get adapters still so I can use them with my PoE switch.
Hardware Version: v2
Firmware Build: 3.12.16 Build 120224 Rel.61005n
Wireless Mode: Access point
Channel: Auto
Mode: 11bgn mixed
Channel Width: 20/40MHz
Max TX: 300MBPs
About a week after getting these units installed and having them work great, I started running into problems. One of the unit's system light was not on, and I could not connect to the access point from my phone, or log into the web interface. I did a soft reboot (unplug for 30 seconds, plug back in) and it seemed to work fine, but then I had the same problem, and soon both units were doing it. I thought i might be pushing the distance limit the stock injectors have, but then I started having the same problem with a unit that is 10 feet from the injector.
View 11 Replies
View Related
Mar 21, 2011
I recently (Jan 2011) bought a new DLink DIR-600 Router for my home use. It was working excellent for last two months and suddenly last Monday all hell broke loose. I have a WiMax connect and have a POE box. I plugged in the cable from POE box into my router and it used to work fine. But now, the globe indicator on the router box is not turning green. It remains yellow. When I remove the POE cable from router and plug it directly to my laptop, it works fine.
View 2 Replies
View Related
Mar 22, 2011
I've been using my Router For 2 months now, It's been working properly since. But yesterday, It was left turned ON and the Power and Globe LED's were orange/yellow. As I restarted the router (unplugged, waited for 1 min.) Only the Power LED was green, all the other LED's were OFF.
View 1 Replies
View Related
Apr 15, 2011
1 =if its a rev 1c on the sticker that makes it DIR-615_REVC I am assuming
2= suddenly it shut down today yellow power lite , i cycled and nothing i reset then got a request to do a firmware update! I shut it down for a hour cycled and after a few minutes green power lite all my settings were still in place?I would think a reset would wipe this out.Its only 2 years old and would be surprised if its dieing.
View 2 Replies
View Related
Mar 24, 2013
I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies
View Related
May 9, 2011
The internet connection light is blue, i am assuming this means the device thinks that it is connected. However wired or wireless I can't hit any web pages. When I use the internal tools neither can the device ping any address.
I am using:
Firmware 2.00NA
DSL modem ATT-Yahoo-SBC (Speedstream 4100 using DHCP)
I am planning to upgrade the firmware to 2.01NA and give that a shot.
View 1 Replies
View Related
Dec 23, 2012
I have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
View 1 Replies
View Related
