D-Link DIR-655 :: Port Link Light For Powered-off Device Stayed On
Nov 20, 2011
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
View 7 Replies
ADVERTISEMENT
Dec 3, 2012
I have a DIR-615 router (h/w ver E4 and firmware 5.10) that needs to be powered off and then on again several times in a day (a reset of sorts).After being on for sometime, most devices lose connectivity to the router and new devices cannot connect to it.After being powered off and then on again, everything works fine.
View 4 Replies
View Related
Mar 6, 2012
My DIR-825 stays on even when I flick the power switch, for as long as I don't disconnect the externally powered Belkin USB hub from it. Some lights do come off, Internet light turns orange, but it stays on. If I disconnect the hub before trying to shut down the router, it turns off instantly.
I feel slightly worried by this because as far as I am aware, a USB client device shouldn't be feeding power to the host. On the other hand, the host shouldn't be accepting power from the client either.
Also, sometimes after days since last reboot, the USB light on the router is not on despite connected devices, and they may or may not appear in Shareport.
View 3 Replies
View Related
Apr 17, 2011
It took a while but I've had my 1522 running well for several days. However, if I power down and then power up the 1522, it never reconnects. The bridge mode light flashes 5 times, then - nothing.
So, I have to disconnect everything, bring the 1522 back to my main PC, attach it, let it connect properly, then unattach and re-attach at it's use site.
(I'm using a static IP address and a Cisco E3000 router working perfectly with all my other stuff. Firmware v1.31)
View 1 Replies
View Related
Feb 20, 2013
Region : Singapore
Model : TL-WR941ND
Hardware Version : V3
I would like to connect a device (dataloger that sends data to a remote server via internet) which only has LAN port to a wireless network on the location. I managed to do this once with WA901ND configured in Client mode (WA901ND acts like a wireless card for this data loger).Does WR941ND support this feature (which feature should I use?) or should I buy WA901ND again?
View 7 Replies
View Related
Feb 28, 2011
i did a reset on my asa by stopping the boot process because i could not remember what my enable password was, i had no problems with the reset the asa came backup as it should and i started configuring the device again. My problem is when the device is powered off and back on i lose all configuration that were made, i save the changes with "write me" before the restart and they are still being over wrote.
View 4 Replies
View Related
Oct 27, 2012
I got 3 new TP-Link WA901ND PoE access points for a wireless network I manage. Right now I'm using the stock injectors that came with them because I need to get adapters still so I can use them with my PoE switch.
Hardware Version: v2
Firmware Build: 3.12.16 Build 120224 Rel.61005n
Wireless Mode: Access point
Channel: Auto
Mode: 11bgn mixed
Channel Width: 20/40MHz
Max TX: 300MBPs
About a week after getting these units installed and having them work great, I started running into problems. One of the unit's system light was not on, and I could not connect to the access point from my phone, or log into the web interface. I did a soft reboot (unplug for 30 seconds, plug back in) and it seemed to work fine, but then I had the same problem, and soon both units were doing it. I thought i might be pushing the distance limit the stock injectors have, but then I started having the same problem with a unit that is 10 feet from the injector.
View 11 Replies
View Related
Mar 21, 2011
I recently (Jan 2011) bought a new DLink DIR-600 Router for my home use. It was working excellent for last two months and suddenly last Monday all hell broke loose. I have a WiMax connect and have a POE box. I plugged in the cable from POE box into my router and it used to work fine. But now, the globe indicator on the router box is not turning green. It remains yellow. When I remove the POE cable from router and plug it directly to my laptop, it works fine.
View 2 Replies
View Related
Mar 22, 2011
I've been using my Router For 2 months now, It's been working properly since. But yesterday, It was left turned ON and the Power and Globe LED's were orange/yellow. As I restarted the router (unplugged, waited for 1 min.) Only the Power LED was green, all the other LED's were OFF.
View 1 Replies
View Related
Mar 2, 2011
I am trying to light up every port light on a 3750g. There is not anything plugged into them and I would like to know (just for fun) is there a way to make every port light 1 - 48 turn on using a command?
View 3 Replies
View Related
Aug 15, 2011
I just bought the wireless-g range expander from a computer parts store.... its not brand new, and i don't have the cd. It is picking up the wireless signal and my laptop sees that it is excellent signal strength but it won't connect to it and the "Link" light is red
View 1 Replies
View Related
Apr 15, 2011
1 =if its a rev 1c on the sticker that makes it DIR-615_REVC I am assuming
2= suddenly it shut down today yellow power lite , i cycled and nothing i reset then got a request to do a firmware update! I shut it down for a hour cycled and after a few minutes green power lite all my settings were still in place?I would think a reset would wipe this out.Its only 2 years old and would be surprised if its dieing.
View 2 Replies
View Related
May 5, 2013
I've had major issues connecting to the Internet in the last couple days. I can't think of anything specific that was changed. The lights on the front:
Power light - steady on.
Circle/triangle light - flashes at approx once per second.
4-circle light - intermittent quick flashes (but mostly on).
Wireless light - COMES ON FOR THREE SECONDS EVERY FIFTEEN SECONDS!
All the lights are green.
Dir-655
Hardware A1/a2
Firmware 1.35NA
I tried turning SEP off. No luck. To note, the Internet works when I hard wire a computer through the dir-655.
View 1 Replies
View Related
Mar 24, 2013
I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies
View Related
May 9, 2011
The internet connection light is blue, i am assuming this means the device thinks that it is connected. However wired or wireless I can't hit any web pages. When I use the internal tools neither can the device ping any address.
I am using:
Firmware 2.00NA
DSL modem ATT-Yahoo-SBC (Speedstream 4100 using DHCP)
I am planning to upgrade the firmware to 2.01NA and give that a shot.
View 1 Replies
View Related
Dec 23, 2012
I have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
View 1 Replies
View Related
Dec 9, 2009
I successfully linked a DIR-655 (A4, FW:1.21) via WPS.
I then updated the DAP-1522 to FW:1.21 from 1.1.
Things looked great. I then moved it upstairs to my home theater.
Plugged it in and got a blinking power light. Completely unresponsive to either linkage or 192.168.0.50.
I have followed everyone advice listed either here or in Amazons reviews. And from my own experience with similar electronics the flashing power LED is indicative of a "brick".
I have initiated a replacement shipment from amazon. Just wanted to see if anyone had seen this before.
View 3 Replies
View Related
Apr 3, 2011
My internet light flashes at times yellow.Some times i lose internet connection .I have never had this problem with my linksys router.
View 3 Replies
View Related
Mar 3, 2013
I have a WPC54G ver. 2 adapter I am trying to get to work on a thinkpad T22 running W2kPRO with all the SPs and updates installed. The power light comes on, but the link light does not. I am using a Linksys WRT54GS wireless router. The monitor icon shows in the taskbar and when I open it, it says the adapter is inactive. I have tried several time to download and install the driver for the Linksys site. It seems to install OK, but when I go back and check the Drivers tab to verify that the driver version has changed to 3.20.21.0, it is still version 6.0.0.18.
View 4 Replies
View Related
Mar 11, 2012
I reseted my router because I couldn't go in the login so now eveything is green except the earth looking thing next.the power it is orange Cause I really need my internet
View 1 Replies
View Related
Mar 23, 2013
Region : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
View 2 Replies
View Related
Dec 18, 2011
My Dir-615 stopped working some weeks ago and I switched to another router until I had time to look at it. Tonight I checked the ps voltage and it read exactly +5v but just for a test I tried another 5v ps (which tested a little higher) and it worked. The ps that works reads about link +7vdc. Before this the power light came on with the occasional blink but I could't connect.
View 5 Replies
View Related
May 11, 2013
I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.
View 5 Replies
View Related
Jan 28, 2011
I have had a Dlink dir 615 for some time now and always had a few issues, but nothing a reboot of the router couldn't solve. This time the problem is persisting, though. The wireless signal keeps blinking and on my laptop it says No internet connection. I've rebooted the router, restored the router, rebooted the modem, and nothing seems to work.
View 1 Replies
View Related
May 31, 2012
For the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.
View 1 Replies
View Related
Mar 3, 2013
Region : Egypt
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : STE
In the past everything was working fine (had same computer connected wireless + wire) never had this disconnection. Now, I have a laptop connected using wireless & desktop wired but this disconnection is becoming so irritating. It is not only that I lose the internet connection, I lose the DSL like (as if the modem is turned off then on) and all my files over the LAN are either lost during transmission or something else.
View 1 Replies
View Related
Apr 11, 2011
Have noticed this in almost a regular pattern. About every 3 seconds the internet light whick is blue most of the time will ocassionally flash white then maybe yellow. Does not appear to interupt internet access yet last only a second (at the longest),so don't know if I would notice. Am connected to DSL modem and see no change it its indicator lights,(traffic, collision, lan), when it occurs on the DIR-655. Have three PC's and a network (LAN) printer as well as wireless enabled. BTW is does not matter if wireless is active. What do the different colors mean ?? Blue = Connected White = Yellow =
View 3 Replies
View Related
Jan 25, 2013
Region : India
Model : TD-W8151N
Hardware Version : Not Clear
Firmware Version :
ISP : MTNL
my ADSL light doesn't get on during my afternoon hours...after so many try too it get switch on after somewhat 5-6pm...
View 1 Replies
View Related
Mar 25, 2013
Region : Others
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.11.3 Build 100408
ISP : Telekom
the SYS light, keeps blinking is that normal?
View 2 Replies
View Related
Jan 21, 2011
I recently switched from a DSL ISP (Earthlink, Zyxel modem configured as a bridge, pppoE connect) to a cable ISP (Comcast, Arris cable modem, dhcp connect). Basically PC --> DIR615-->Cable modem-->Internets. With the old DSL the Internet activity LED (green, looks triangular) on the DIR615 blinked only when internet activity occurred. With the new Comcast connection it blinks non-stop about 5 times a second! Even if the PC is turned off it blinks. It stops blinking if I disconnect the ethernet cable between router and modem. The connection itself is fine, but if the DIR615 is doing something it should not be doing it might slow the connection down a bit, (or burn something out prematurely?)FYI, the Arris cable modem does not seem to be a router. It takes a cable connection from outside and provides a single ethernet cable and 2 (voice) telephone cables to the house.
View 1 Replies
View Related
Oct 28, 2012
I've not found any topic related to what happened to me. Bought two cameras and upgraded the firmware on both as asked, but one of them just stopped. The light is solid green and not red like other posts.Tried the recovery procedure, but the browser won't find my camera. Changed computer IP and everything else that was told to be done. Nothing works!! I also can't find any posts relaled to my problem all over the internet.
View 3 Replies
View Related
May 8, 2013
I just completed installation of a stacked pair of 3850s in my datacenter. While I was installing them, I noticed that the lights on ports 1-8 on one of the switches were on solid even though there were no cables connected to that switch. I don't see anything in the logs or anywhere else in the CLI that indicate a problem, however the lights remain on. This only happens on switch 1, not switch 2. Once I plugged the cable into port 1, it flashes normally with activity, but 2-8 remain on solid even though nothing is connected to them.
Before I put the switches in place, I had configured them at my desk with the console connection, and those lights were not lit up.
The indicators on the front of both switches are set in STAT mode. I thought initially I had hit the button and flipped it to a different mode, but that is not the case.
View 5 Replies
View Related
Oct 19, 2011
So I just noticed on my Cable modem the link light is blinking orange, per Motorola if its blinking orange - Computer is connected via a 10 mbps or 100 mbps Ethernet port.
On the Linksys E4200 status page it says
Internet Port Speed:
Internet 10/100 mbps
Local Port Speed Port 1 - 1Gbps
Maybe I just noticed this with this router, but I'm pretty sure this didn't start happening until I updated to 1.0.03.
Previously the link light was blue indicating a 1Gbps connection.
View 4 Replies
View Related
