I have a DIR-615 router (h/w ver E4 and firmware 5.10) that needs to be powered off and then on again several times in a day (a reset of sorts).After being on for sometime, most devices lose connectivity to the router and new devices cannot connect to it.After being powered off and then on again, everything works fine.
View 4 Replies
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
My DIR-825 stays on even when I flick the power switch, for as long as I don't disconnect the externally powered Belkin USB hub from it. Some lights do come off, Internet light turns orange, but it stays on. If I disconnect the hub before trying to shut down the router, it turns off instantly.
I feel slightly worried by this because as far as I am aware, a USB client device shouldn't be feeding power to the host. On the other hand, the host shouldn't be accepting power from the client either.
Also, sometimes after days since last reboot, the USB light on the router is not on despite connected devices, and they may or may not appear in Shareport.
It took a while but I've had my 1522 running well for several days. However, if I power down and then power up the 1522, it never reconnects. The bridge mode light flashes 5 times, then - nothing.
So, I have to disconnect everything, bring the 1522 back to my main PC, attach it, let it connect properly, then unattach and re-attach at it's use site.
(I'm using a static IP address and a Cisco E3000 router working perfectly with all my other stuff. Firmware v1.31)
For the last several months, but progressively worse, my internet drops due to the DNS Server not responding. This happens across my whole network and the only fix I can come up with is to reset the router every time it does this. At this point I am thinking a new router is in order (but do not have the money atm), I am using a D-Link DIR-625 V. C1 Firmware 3.08 router and a Motorola SB6120 modem. Is there another permanent fix for this problem is or my router on it's last legs? Would setting a new DNS Server on my router work?
View 11 Replies View RelatedRegion : Spain
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Telefonica-Spain
'm having the same problem my tp-link freezes several times a day and only a hard reset will get it working again. I have no idea how to fix it, I have contacted tp-link support and they say to make sure I have all the right ADSL configuration parameters.
I bought a new DIR-655 REVB router, I already own the first version of the DIR-655 and worked fine, but the wireless range wasn't always the highest upstairs in my house and I was hoping with REVB they had improved the DIR-655's range. I'm not a big wireless guy, meaning if I can use a hardwire connection I will use it, so my house is pretty well wired, but for my daughter and son's ipod and Zune the wireless connection was weak in their upstairs bedrooms. It has been a disaster, the wired connections gets disconnected constantly, I say in the subject title 100's of times a day and I don't think I am exaggerating. It started with Netflix and I thought my son was crazy, how could new router do this, but it was doing it everywhere. It is hard to download files because I lose my connection. I have DSL through Windstream. My solution is to reinstall my old DIR-655.
View 8 Replies View RelatedRegion : Sweden
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : Ownit
I am having problems with my TL-MR3420 router, it disconnects WIFI all the time. This occur several times a day and is very annoying.
I have quite recently upgraded to the latest firmware but the problem seem not to have been resolved. It also seem that it is mostly the WIFI service that is the problem. The usage of wired routing is working even when the WIFI is disabled.
For the past year or so, 5-6 times a day my router's green internet light will turn red, needing a reset... 99% of its usage is through wired connections and this is the only router in my home.
View 1 Replies View RelatedRegion : Others
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Baltcom TV
I have very low speed with router.First test without router - using cable directly to PC (DLINK DGS-3210 Managed SW - > My PC), here is result : Second test, using WR1043ND router (DLINK DGS-3210 Managed SW - > WR1043ND Router -> My PC), here is result : First of all, i thought that maybe WAN port is 100Mbit mode, but after i checked it on SW - port is still in 1Gig Mode (from router to PC, it is also 1Gig)Also downloading speed have same picture...Without router i get around 55MB/s, with router max that i saw is ~14MB/s....
Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : newest
ISP : CS
the router lost Wifi signal 5-10 times per day.Router and devices are in the same room. max 4 meters.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Bell Canada
We have a WDR4300 router that works well about 98% of the time. We have a static IP address from our ISP configured through PPPoE in the router and are hosting our own email and web server at local IP 192.168.1.200 behind the router. Port forwarding is enabled and working beautifully.
At some times throughout the day, any computer behind the router on our local network is unable to browse to our own website by our domain name (e.g. www.xyz.com) nor by the static IP it is attached to. We also get e-mail errors with mail client configured to use the domain name or the static IP it is attached to as the outgoing mail server. When this happens, I am still able to browse any other site on the internet without problem... just not our own. Also, I have verified that while this is happening (internal computers can access the internet but not our own website):
1) I can browse to our website just fine from a computer outside of our network (e.g. a proxy or a computer controlled remotely from my home)
2) a computer from within the office that cannot reach our website using the domain name or the static IP it is attached to can still reach the website by browsing to the local IP address of the web server (192.168.1.200)
3) the problem seems to resolve itself sometime within 45 minutes of noticing it is occurring if we do nothing. We can make the problem resolve itself sooner by restarting the router.
I have the impression that this problem MIGHT start occurring when users are downloading files from our website. Of course, if this is the case, we cannot simply restart the router to fix the problem because then we are cutting off their download.
I have a question on 300 series PoE switch (SRW224G4P, power budget: 180W). How many WAP 4410N can be powered by this switch??How many AP 1242 can be powered by this switch? Since CDP is not supported yet, I think switch will provide 15.4W power for each AP. So each switch can power up to 11 WAP4410N or AP 1242. Is this correct??
One other quesiton is When CDP is supported, can I calculate as below? WAP4410N (Power draw:10.1W): 180/10.1W = 17.xx -> Up to 17 WAP4410N can be powerd AP1242 (Power draw:12.4W): 180/12.4W = 14.xx -> Up to 14 WAP4410N can be powerd
I'm having trouble getting my evga 680i to wake on lan from a powered off state. I've done it before but for some reason now it doesn't seem to work. I have formatted since the last time I used wake on lan.
I've got all the settings right in the bios and everything. WOL is enabled in the networking properties on the adapter and in the bios. I can wake from a sleep or hibernate state - just not powered off. Using a WOL test client it confirms it is receiving the magic packet.
When my comp is off I dont see the network port light up with the LEDs. I imagine this has something to do with it -- i just dont know what had to go to power management on the configure tab of my network adapter and uncheck the box "allow windows to power off this device to save power" even though I also had under that checkbox "allow wake on lan" checked.
3502i's LED light turn white? Ifso, what does it mean? The info on the LED lights does not mention white. The serial port and the data port are non responsive, but the unit stays powered over PoE.
View 22 Replies View RelatedI've had this router for just over a year now so the warranty is out and it just so happened to stop functioning last night. I'm fairly decent in the router world since I am studying for my CCNA, so I have tried just about anything imaginable. I woke up this morning with no connection, checked the modem, then the router. The router was powered on, but the up/downstream lights were not doing a thing. The modem is not the issue (I am hardwired as of now). I have tried both resets, including unplugging the device, and still can't get a response out of it. The logo light will turn straight on (no fad in and out like it's suppose to) and then it does absolutely nothing. I have never encountered this sort of problem on a home router before. I can't login to the router either.
View 5 Replies View RelatedI have a WAP4410N new out of the box will not stay powered on any of our three 3550 24 port PoE switches running 12.2(25) ipservicesk9-M EMI. The WAP4410N is running the 2.0.3.3 firmware. Unfortunately the AP is the only PoE device I have at my disposal. The device will power on, the link will come up on the switch but after ~5 seconds the power light then the PoE light on the WAP4410N turns off and the device reboots and continues this cycle. The WAP4410N operates normally when plugged in with the included power adapter, but I need to use this as a PoE device.
View 9 Replies View RelatedBackground info:
Comcast cable internet and TV
Regular modem
Linksys WRT54G router
Windows7 desktop
The problem I'm seeing is that our wireless connection cuts out about 5 minutes after turning on our main desktop. Turn off the main desktop and wireless begins to work again. Throughout all of this, the wired connection works fine, and I have no problem connecting to the router either.
I recently upgraded my WRT610N to Firmware Version: 2.00.01 and now the unit powers down on its own after a few hours. Are there any known issues with this firmware?Is there any way to roll back to the previous version of the firmware?
View 4 Replies View RelatedI discovered on a pair of SG300-28P.
On a second switch (ver 1.2.7.76) when I unplugged the power cord, to my amazement the switch turned right back on (about 1 second later), with the power cord removed. To verify that the power is indeed coming from POE, the upstream switch (ver 1.1.2.0) that is the same model (sg-300-28p), shows all 7 Ethernet ports connecting the two drawing from 2700mW, to 3000mW.
While the second switch is powered from the first over POE, the POE does not work on the second switch to power anything, and the system summary mentions something about "PoE Power Information on Master Unit".
Is this a stacking operation, and is POE on the second switch NOT supposed to work when powered over Ethernet from an upstream switch?
I have a 6509 that has dual SUP32's.Just want to make sure and give a reason(if there is one). Slot 6 always becomes the active hot on a full reboot. Meaning from no power to the whole switch to powered on. What is the election process for Supervisors?
View 5 Replies View Relatedi did a reset on my asa by stopping the boot process because i could not remember what my enable password was, i had no problems with the reset the asa came backup as it should and i started configuring the device again. My problem is when the device is powered off and back on i lose all configuration that were made, i save the changes with "write me" before the restart and they are still being over wrote.
View 4 Replies View RelatedMy wrt110 firmware .05 has been working fine until now. I have a couple of phones, 2 printers, 3 laptops and a wii happily connecting to it. However now when I power on the wireless device, nothing can connect wirelessly. Wired connection is fine, but my wireless network disappears. No device can find the network, although it is there and set up on the admin pages. I pull the power chord out for 30 seconds and try again to get it going again, a bit like trying to start a car. Everntually devices find the network.
On two occasions it has forgotten the wireless settings and restored an open 'linksys' network. It's really infuriating becuase whilst I restore the SSID and use the same key, not all the devices actually recognise it and have to be reconfigured on the devices.
One of our Nexus 7000 modules failed and generated the status below. Could this possibly be a hardware issue?
# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 0 10 Gbps Ethernet XL Module powered-dn
Mod Power-Status Reason
--- ------------ ---------------------------
1 powered-dn Unable to power up card (Power_OK not set)
the site is url... it worked fine 3 days ago, then all of a sudden, it times out. I thought maybe it was down or got hacked again, but other members can get there fine. So I started trying things.They checked to see if my IP was on a BAN list. [code]
View 1 Replies View RelatedI have noticed that all the computers lose wifi connection at a certain time (i.e in the morning and at night).
I think it may be the router. I notice the wifi symbol on my router blinking when my macbook pro is not connected to the router after it disconnects by itself.
I have a vpn connection with speed limit .. I want to connect to it multiple times to increase speed?
View 2 Replies View RelatedIt doesn't load certain websites, some of these include Youtube, Tumblr, iTunes, and a few MMORPGs (MapleStory, WoW, StarCraft, to name a few). I later discovered that it doesn't "not load", rather it times out after a second or two. It begins at maybe 500kb/s but then it just stops. No errors, and no resuming on its own.When I download things, I can pause/resume for it to have that burst 500kb/s for a couple seconds. Similarly I can refresh a youtube page multiple times for it to keep loading. It's okay for documents, but if you can imagine downloading a larger file or watching a video, this can become rather frustrating. This problem affects all browsers and applications that uses the internet.I'm on Windows 7 home premium, router is Linksys WRT54G. I've tried /ipconfig release, but it has no effec
View 5 Replies View RelatedI've been having an issue recently which is causing my internet to disconnect for under 20 seconds 1-5 times a day. This can be troublesome when online gaming, as I am normally disconnected from the server.
View 1 Replies View RelatedI have an ADSL 2+ connection that constantly seems to be dropping at random intervals for no particular reason that i can tell anywhere from 3 to 20 times a day for over 6 months.I have a Dlink DIR-300 router which connects hard 2 pcs and a wirless connection that host for 4 devices , the Router is connected to my Dlink DSL-502T Gen 2 ADSL 2+ Router.I'm constantly having to disconnect the power wait 5 minutes and reconnect the power to get everything back online. From what i can tell the main problem is the DIR-300 router, ive checked it has the latest firmware, reset the router from factory, tested it with less connections, called up my ISP and checked everything was good on there end but to no avail[CODE]
View 2 Replies View RelatedI'm using a Thompson DCM475 modem and a D-Link DIR-655 router with updated firmware. It's been 8 months now, and the problem started about two months ago.On average 5 times a day, the whole network would disconnect from the internet. Below is the log from the router:[code] Few days before this two months, instead of the whole network, only the wifi users will experience disconnects.
View 14 Replies View RelatedWho is your Internet Service Provider (ISP)? India- AirtelWhat type of Broadband connection are you using? DSLWhat is the exact Make and Model of your Modem, Router or Modem/Router Please refer to this page with detailed specs: Brand New Beetel 450TC1 Wifi Wireless Modem Router DSL ADSL 2+ BSNL AIRTEL MTNL | eBayWhat is the Name of the Anti-Virus, Security or Firewall Software installed from the problematic computer -Microsoft Security Essential. i have tried uninstalling the antivirus software but no effect!The issue is when i click any link online it displays the following message. Then i go back and do this 3-4 times till its able to load the link.I have had this issue with other browsers. Mostly i use Google chrome. This issue is with wired and wireless connection both.PS: My router is transmitting 2 ssid's at the same time. I am unable to change it.
View 5 Replies View RelatedMy internet connections drop frequently am still able to go on the router website when the internet drops is the router timing me out or what i have a net gear ive tried disabling passphrases?
View 3 Replies View Related
