Cisco Switches :: SG300 Stacking And Powered From POE By Upstream Switch?
Sep 11, 2012
I discovered on a pair of SG300-28P.
On a second switch (ver 1.2.7.76) when I unplugged the power cord, to my amazement the switch turned right back on (about 1 second later), with the power cord removed. To verify that the power is indeed coming from POE, the upstream switch (ver 1.1.2.0) that is the same model (sg-300-28p), shows all 7 Ethernet ports connecting the two drawing from 2700mW, to 3000mW.
While the second switch is powered from the first over POE, the POE does not work on the second switch to power anything, and the system summary mentions something about "PoE Power Information on Master Unit".
Is this a stacking operation, and is POE on the second switch NOT supposed to work when powered over Ethernet from an upstream switch?
View 2 Replies
ADVERTISEMENT
Apr 28, 2013
I have inherited a custome with a bunch of SG300's in their LAN room and one out in the warehouse.I need to setup a VLAN and the genius before me did not label which LAN room switch the warehouse unit plugs into. Is there a tool/method I can use to find which switch, and port this warehouse switch is connected to?
View 2 Replies
View Related
Nov 7, 2011
So it seems like the SG300 series (have here sg300-52) can be run as standalone unit and also in stacking mode. but i can not find any documentation or howto for this.
View 8 Replies
View Related
May 9, 2011
I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies
View Related
Sep 10, 2011
I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies
View Related
Oct 12, 2011
Mgmt Vlan 1 (default) Data VLan 10 (with access to internet) Is there a way to have a PC attached to a SG300 switch such that it can both access Vlan 10 for data and Vlan 1 for managment ? The PC's port clearly needs to be untagged PVID on vlan 10. I have tried adding vlan 1T and setting the port as a trunk port but to no avail, The switch is currently level 2. I am guessing this might not be possible in level 2 without setting the mgmt vlan to 10 ?.
View 3 Replies
View Related
Feb 3, 2013
i have a SG300-52 Switch, route mode is enabled, and it is using the latest IOS.I have created 4 Vlans in this switch, till this point its OK, but once i try to give ip addres to the created Vlan either from the GUI or CLI the switch is not responding. i have to go and manually reset the switch using a pin.
View 8 Replies
View Related
Mar 4, 2012
i was trying to set up a new SG300-52 L3 switch for switching and Vlan. The problem is that the vlans on this switch cannot get their DNS resolved. Probably a stupid thing i can't get to see, but i think it is a simple solution given switchin is not my expertise.So my setup:
- ISP Wan router: LAN ip 10.0.0.1, DMZ: 10.0.0.2 -> i have to use this router for ISP support. But it suckes, that's why we use own router for firewall, port forwarding etc.
- Nice Router: WAN: 10.0.0.2, LAN: 192.168.1.1
- SG300 L3 switch
This works. I can ping switch, nice router, ISP router and google's ip from VLAN 5.But i cannot ping google using host name. From within SG300 i can. So it has something to do with SG300 not doing DNS right.My Client on VLAN 5 has ip 10.1.1.5 / 24, default gateway and dns pointing to switch: 10.1.1.1.I have put an entry in DNS servers in SG300: 192.168.1.1 active (pointing to Nice router). On client leave default gateway pointing to switch. But put DNS server : 192.168.1.1
View 11 Replies
View Related
Oct 10, 2011
I have a recently purchased 28 port SG300 switch. Everything is working well. Unfortunately there is so much traffic flying around that a 10MB half duplex device is struggling to function as it is overloaded. Removing some of the sources of traffic fixes it.
Fortunately I only need to access that device from one PC on the network. That PC however needs to access everything else on the network.
Is there a simple way to shield the slow device from everything except traffic from the PC ?
The switch is in Level2 mode at the moment. Everything is on a single sub net.
View 2 Replies
View Related
Sep 1, 2011
We have 2 separate networks here, 1 for data (192.168.0.x) and 1 for VOIP phones (192.168.3.x).
I need them to both be connected to different ports on a switch (Cisco SG 300 10 port managed switch) which is then linked to another switch (Cisco Catalyst 2960 48 port switch). Then on this 2960 switch I want the link to be split back into the 2 separate networks. I think that I need to create 2 separate VLANs and assign them to different ports.
View 2 Replies
View Related
Feb 8, 2013
What does "ip routing" do on the CLI on the SG300? When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it. I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
View 2 Replies
View Related
Jan 18, 2013
My problem is that the switch all of the sudden doesn't boot up anymore. The System LED constantly flashes, after probably 40-50 seconds or so it constantly lights for a second, afterwards all the lights on the ethernet ports light up for a second and the process starts all over again! The console messages:
Device configuration:Slot 1 - SG300-10PDevice 0: GT_98DX3033B (AlleyCat2)
-------------------------------------- Unit Standalone --------------------------------------
Tapi Version: v1.9.5Core Version: v1.9.519-Jul-2012 17:55:03 %INIT-I-InitCompleted:
[Code].....
View 3 Replies
View Related
Oct 22, 2011
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
View 6 Replies
View Related
Dec 5, 2012
I am having some issues with getting DHCP Relay to fuction properly over our SG300-20 Switch.Out current layout is as follows. Hanging off the SG300-20 are a pair of Clustered Checkpoint Gateways with VLAN'ed interfaces in Both of our 2 VLANs, a 3COM 4200G In VLAN1 which has the DHCP server (And all the other Servers) connected to it, and a Pair of HP Procurve 2520's Stacked in VLAN 2 to provide PoE for our Phones/connectivity for our PCs.The problem is I cannot get the DHCP Relay to fuction from VLAN 1 to VLAN 2. If I assign an address in VLAN 2 manually to a device connected to the Procurves, everything works fine. I am able to reach both VLAN 1 and VLAN 2, but DHCP aquisition fails even if the device is connected directly to a port assigned to VLAN 2 on the SG300. The SG300 is running at Layer 3 currently also.
Here is a copy of the running config:
--------------------------------------------------------------------------------------------------------------
switch4db24f#show running-config
vlan database
vlan 2
exit
interface range gi8,gi16
switchport default-vlan tagged
[code]....
View 6 Replies
View Related
Aug 30, 2011
Our customer use catalyst switch that spanning tree be PVST+ mode.I take SG300 connect with this catalyst switch.Does it support ?If it support,how to config on SG 300 ?
View 1 Replies
View Related
Mar 9, 2012
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
View 1 Replies
View Related
Apr 1, 2012
I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
[code]...
View 2 Replies
View Related
Jun 7, 2011
I have a question on 300 series PoE switch (SRW224G4P, power budget: 180W). How many WAP 4410N can be powered by this switch??How many AP 1242 can be powered by this switch? Since CDP is not supported yet, I think switch will provide 15.4W power for each AP. So each switch can power up to 11 WAP4410N or AP 1242. Is this correct??
One other quesiton is When CDP is supported, can I calculate as below? WAP4410N (Power draw:10.1W): 180/10.1W = 17.xx -> Up to 17 WAP4410N can be powerd AP1242 (Power draw:12.4W): 180/12.4W = 14.xx -> Up to 14 WAP4410N can be powerd
View 1 Replies
View Related
Nov 18, 2012
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies
View Related
May 19, 2012
I have a 6509 that has dual SUP32's.Just want to make sure and give a reason(if there is one). Slot 6 always becomes the active hot on a full reboot. Meaning from no power to the whole switch to powered on. What is the election process for Supervisors?
View 5 Replies
View Related
Dec 13, 2011
We had a SGE-2010, just purchased 2 (two) SGE-2010P. I want to stack the switches (all 3) (unless there is a better way). Not sure what is needed hardware wise, and how to physically wire the switches. Had switches years ago (diff brand) that used a special cable that connected the switches. It seems that is not the case here. I have not used fiber in networking before so I am new to that part, I’m willing to learn, just need pointed in the right direction.Can all three switches be stacked, (1) SGE-2010 & (2) SGE-2010P? I THINK I need to use the GBIC port 4 to stack, I understand 1 port is enough if two switches are used, but what about three or more switches.What are the other GBIC ports used for? Will I be better off (can I ) use the GBIC ports LAG (2 ports) to the other switches? Or would regular ports work just as well?
View 6 Replies
View Related
Aug 29, 2011
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
View 1 Replies
View Related
May 26, 2011
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
View 2 Replies
View Related
Feb 8, 2012
Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies
View Related
Jul 25, 2012
I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies
View Related
Dec 22, 2011
2 routers in series, is one more secure. I recently asked about setting up two routers in series as routers, one wireless one not. It was my understanding that the computers on the second router would not be visible to computers on the first router, the wireless one. My assumption was that this would make it more difficult for someone who got access to the wireless router to also access those computers on the second router.
View 3 Replies
View Related
Sep 24, 2012
Having a design where an IBM bladecenter has two Nexus 4001i switches and each switch is connected to a Nexus 5k vPC pair, is it possible to configure active-active nic teaming on the hosts (blades) considering that the Nexus 4k switches are unaware of each other and blade has one connection to each 4k over either emulex or qlogic 10G CNA?
View 1 Replies
View Related
Mar 11, 2012
I have an issue with a Cisco 3750 switch stack which is connected to two seperate upstream Cisco 3750's which are administered by an ISP. The ISP is experiencing MAC address flapping from one of my VLAN SVI's i am using to route traffic upstream
[code]...
As you can see I utilise a VLAN SVI to route traffic to the upstream 1.1.1.2 (illustration only) IP. As per the diagram of the topology attached, the ISP is receiving a MAC address flapping error confirming the SVI MAC address from my switch stack is being learnt on the trunk port connecting switch 1 and switch 2, and also the port (Gi1/0/48) directly connected to my switch stack. As these are all Layer 2 links essentially being passed upstream and then connected between the two ISP switches, we have a 3 way triangular loop formed.
If I was to remove the port channel configuration from the two ports associated with the VLAN SVI, am i right in suggesting this would still form a layer 2 loop? The two ports would still be a member of the SVI VLAN, and it is the VLAN MAC address which is being learnt by the two ISP switches on different interfaces.
View 2 Replies
View Related
Apr 30, 2012
show logging
May 1 16:00:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:00:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:17:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to down
May 1 16:17:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/12, changed state to up
May 1 16:25:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
May 1 16:25:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
May 1 17:19:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
Configuration as below:
macro name vmware
switchport trunk encapsulation dot1q
switchport mode trunk
no switchport access vlan
[code].....
Note:Both active blade switch and standby one are connecting to same aggregate switch 3750. Yet the active one, with same config as standby one, has not occurred this issue.
View 2 Replies
View Related
Apr 7, 2012
Im trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.
They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
[Code]....
View 1 Replies
View Related
Jul 20, 2012
Does the SF300 support stacking? If it does, which port(s) are the ideal ones?
View 1 Replies
View Related
Jun 4, 2013
I have a Cisco SG500-52P along with an older SGE-2010P, am I correct that in order to stack they must be the same series?
View 1 Replies
View Related
May 29, 2013
I am currently running two SGE2010 in stack and planning to purchase new Sg500 .I have two questions :
1. If these two different products can be managed as one stack.
2. Are the SFP (mini-GBIC) connections compatible and if so what accessories or parts do we need to enable them?
View 1 Replies
View Related
