Cisco Switches :: SG300 Can PC Manage Switch And Get Data From It
Oct 12, 2011
Mgmt Vlan 1 (default) Data VLan 10 (with access to internet) Is there a way to have a PC attached to a SG300 switch such that it can both access Vlan 10 for data and Vlan 1 for managment ? The PC's port clearly needs to be untagged PVID on vlan 10. I have tried adding vlan 1T and setting the port as a trunk port but to no avail, The switch is currently level 2. I am guessing this might not be possible in level 2 without setting the mgmt vlan to 10 ?.
I have a customer with several SG300's providing VLAN1 for data and VLAN10 for voice. The PC's are piggy backing off the phones and showing up in the SG300 fine:
One department has recently employed more people so we have an SG200 switch to connect the computers and phones to. I don't seem to be able to get any connectivity between the new switch and the SG300 it is connecting to. I have setup VLAN1 and 10 as per the images below:
I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
i have a SG300-52 Switch, route mode is enabled, and it is using the latest IOS.I have created 4 Vlans in this switch, till this point its OK, but once i try to give ip addres to the created Vlan either from the GUI or CLI the switch is not responding. i have to go and manually reset the switch using a pin.
i was trying to set up a new SG300-52 L3 switch for switching and Vlan. The problem is that the vlans on this switch cannot get their DNS resolved. Probably a stupid thing i can't get to see, but i think it is a simple solution given switchin is not my expertise.So my setup:
- ISP Wan router: LAN ip 10.0.0.1, DMZ: 10.0.0.2 -> i have to use this router for ISP support. But it suckes, that's why we use own router for firewall, port forwarding etc.
- Nice Router: WAN: 10.0.0.2, LAN: 192.168.1.1
- SG300 L3 switch
This works. I can ping switch, nice router, ISP router and google's ip from VLAN 5.But i cannot ping google using host name. From within SG300 i can. So it has something to do with SG300 not doing DNS right.My Client on VLAN 5 has ip 10.1.1.5 / 24, default gateway and dns pointing to switch: 10.1.1.1.I have put an entry in DNS servers in SG300: 192.168.1.1 active (pointing to Nice router). On client leave default gateway pointing to switch. But put DNS server : 192.168.1.1
I have a recently purchased 28 port SG300 switch. Everything is working well. Unfortunately there is so much traffic flying around that a 10MB half duplex device is struggling to function as it is overloaded. Removing some of the sources of traffic fixes it.
Fortunately I only need to access that device from one PC on the network. That PC however needs to access everything else on the network.
Is there a simple way to shield the slow device from everything except traffic from the PC ?
The switch is in Level2 mode at the moment. Everything is on a single sub net.
We have 2 separate networks here, 1 for data (192.168.0.x) and 1 for VOIP phones (192.168.3.x).
I need them to both be connected to different ports on a switch (Cisco SG 300 10 port managed switch) which is then linked to another switch (Cisco Catalyst 2960 48 port switch). Then on this 2960 switch I want the link to be split back into the 2 separate networks. I think that I need to create 2 separate VLANs and assign them to different ports.
What does "ip routing" do on the CLI on the SG300? When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it. I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
My problem is that the switch all of the sudden doesn't boot up anymore. The System LED constantly flashes, after probably 40-50 seconds or so it constantly lights for a second, afterwards all the lights on the ethernet ports light up for a second and the process starts all over again! The console messages:
Device configuration:Slot 1 - SG300-10PDevice 0: GT_98DX3033B (AlleyCat2) -------------------------------------- Unit Standalone -------------------------------------- Tapi Version: v1.9.5Core Version: v1.9.519-Jul-2012 17:55:03 %INIT-I-InitCompleted:
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0 -VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
On a second switch (ver 1.2.7.76) when I unplugged the power cord, to my amazement the switch turned right back on (about 1 second later), with the power cord removed. To verify that the power is indeed coming from POE, the upstream switch (ver 1.1.2.0) that is the same model (sg-300-28p), shows all 7 Ethernet ports connecting the two drawing from 2700mW, to 3000mW.
While the second switch is powered from the first over POE, the POE does not work on the second switch to power anything, and the system summary mentions something about "PoE Power Information on Master Unit".
Is this a stacking operation, and is POE on the second switch NOT supposed to work when powered over Ethernet from an upstream switch?
I have inherited a custome with a bunch of SG300's in their LAN room and one out in the warehouse.I need to setup a VLAN and the genius before me did not label which LAN room switch the warehouse unit plugs into. Is there a tool/method I can use to find which switch, and port this warehouse switch is connected to?
I am having some issues with getting DHCP Relay to fuction properly over our SG300-20 Switch.Out current layout is as follows. Hanging off the SG300-20 are a pair of Clustered Checkpoint Gateways with VLAN'ed interfaces in Both of our 2 VLANs, a 3COM 4200G In VLAN1 which has the DHCP server (And all the other Servers) connected to it, and a Pair of HP Procurve 2520's Stacked in VLAN 2 to provide PoE for our Phones/connectivity for our PCs.The problem is I cannot get the DHCP Relay to fuction from VLAN 1 to VLAN 2. If I assign an address in VLAN 2 manually to a device connected to the Procurves, everything works fine. I am able to reach both VLAN 1 and VLAN 2, but DHCP aquisition fails even if the device is connected directly to a port assigned to VLAN 2 on the SG300. The SG300 is running at Layer 3 currently also.
Here is a copy of the running config: -------------------------------------------------------------------------------------------------------------- switch4db24f#show running-config vlan database vlan 2 exit interface range gi8,gi16 switchport default-vlan tagged
Our customer use catalyst switch that spanning tree be PVST+ mode.I take SG300 connect with this catalyst switch.Does it support ?If it support,how to config on SG 300 ?
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports) and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
I should set up a network for a little enterprise.The requirements can be summarized as follows:
- All the "business" softwares have to be stored in a single computer (let's call it "the server"). The other computers (in this case there should be at most 2 or 3 computers) can execute these softwares through the server. So there are no local copies of those softwares on clients, only on the server. - The main computer (the server) shares also a printer. - All the computers in the network, are interconnected through a single wi-fi modem/router. Some of them are connected through the wi-fi interface and others through an ethernet cable.
the server, in order to perform some special procedures, has to connect to a special modem which connects it to a remote private network. In order to do so, the server disconnects from the local enterprise network because Windows does not allow me to stay connected to more than one network at the same time.The remote private network does not require to disconnect from any other network, it's just a constraint imposed by Windows.In the meantime, clients are not able to execute softwares anymore and cannot print anything.when the server is connected to the private network, it still needs to execute the "business" softwares.
Is it possible to keep the server connected to both the networks without denying the access to softwares, data and printers to anyone? If yes, how?If not, how can I design the topology of the network in order to share softwares and other data among all the computers (server and clients)? It's important that when the server connects to the private network every computer (including the server itself) can still access softwares, data and printers.
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version switchd64684#show version SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 ) Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 ) HW version V01
I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
I would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.
I'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
My understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
I have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
