Program To Manage Switch
Sep 8, 2011I have a dell powerconnect 3448 and am trying to find a good program to use to manage the switch.
View 7 RepliesI have a dell powerconnect 3448 and am trying to find a good program to use to manage the switch.
View 7 RepliesI have only one LAP-1142N-E-K9. It is controller based AP but i dont have WLC. I want to manage these AP with a HP Switch. (HP 1910-24G-PoE)
But i dont known that a LAP-1142 is competible? If yes, how can i manage or configure these LAP with HP switch?
Mgmt Vlan 1 (default) Data VLan 10 (with access to internet) Is there a way to have a PC attached to a SG300 switch such that it can both access Vlan 10 for data and Vlan 1 for managment ? The PC's port clearly needs to be untagged PVID on vlan 10. I have tried adding vlan 1T and setting the port as a trunk port but to no avail, The switch is currently level 2. I am guessing this might not be possible in level 2 without setting the mgmt vlan to 10 ?.
View 3 Replies View RelatedIs it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?
View 1 Replies View RelatedI am a very basic user on the Cisco Switch programming. I was given a Cisco 3750G-48 to tinker with in my home office. I was wondering if someone could lead me to some good sources of information to program and configure this switch? I am wanting to create a GB network in the house with the computers that I have and the storage arrays.
View 8 Replies View RelatedMy understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies View RelatedI have a client whom has asked me to enable web management on some of his 2960 switches. I did not think this was going to be an issue, and so I told the customer I would set this up for him.
Much to my dismay, I have been able to get http and https enabled, and then authenticating locally for the HTTP access. I then come to the screen once authenticated which is shown below:
The issue is that when I select "Web Console", it gives me a "Web Page Cannot be found".
I have three 4506 switches with vlan 4 set as the management vlan. Switch 1 is connected to switch 2 and switch 3.
I can access switch 1 and 2 using telnet from the management vlan and both switches reply to pings. But from switch 1 or 2 I cannot ping or telnet switch 3. If I plug into switch 3 and I can ping and telnet switch 3 but not switches 1 or 2.
It is as if the management vlan 4 is not being passed to/from switch 1 and 3. The configs for the uplinks from switch 1 to 2 and 3 are the same. And the configs for switches 2 and 3 look the same apart from the port settings.
I have over 40 vlans running all that work fine between all the switches.
1. How I can manage those devices, the Switch and the router? What is the BEST SOLUTION to manage this devices?
2. I want to monitor the traffic on this environment, how I can do it? How I can monitor the traffic from customer A, Customer B, and my own LAN traffic, in terms of bandwidth that has passed throught my devices? Is it possible to monitor on MY LAN, or I have to monitor from the EXTERNAL switch?
3. How I can limit the bandwidth? I was trying to configure it using access list, with policy-map, etc....and limit this on each interface. [code]
The interface does not support the specified policy configuration and/or parameter values.Assigning a policy map to the output side of an interface not supported.With I few reading, I could see that the SWITCH 3750 doesnt support this configs.My INTERNET LINK is 30 Mbps, the ports on the Switch (WS-C3750X-48P-L) are Gigabit Ethernet.How I can limit the bandwidth here? For example, How I can limit a interface to 3Mbps..I was thinking about this:
- Limit the interface to 10Mbps: speed 10
- and limit the interface with 30% of this speed: srr-queue bandwidth limit 30
Does this work for both UPLOAD and DOWNLOAD?When the packets passes that 3Mbps limitation, will they be droped?
I use program to connect to internet, named SSH or something. So in that program, I will need to fill the 'port server','IP server', 'port proxy', and 'IP proxy', then click connect. After that a black box similar to CMD box will come up(see image below) and I will be able to surf the internet. I can use IE, firefox, and Steam. But some program like Kaspersky, Yahoo messenger, MSN, ventrilo, teamspeak and the rest won't work at all.
View 11 Replies View RelatedWhy i cannot log in to my vpn program.i successfully installed and run it.. but the problem is i cannot log in.. and my computer will pop up error message..
View 1 Replies View RelatedI use Sage to update my stock on a PC in my back room.I want to access that PC and open the sage program from another 2 PC's, add data, save etc.I thought a simple network would do it but not quite. I have three PC's in different parts of the building.I can see all three PC's and share files, printers etc, but not sure how to execute and run the program through the network on the back PC.I didn't want to set-up a server but in a way this looks like what I need to do.How much more after what i've set-up as a network with all sharing and internet connections etc do i need to do?I'm thinking if i use the PC the program is on as the server, how would i be able to execute the program from another PC in the network.
View 14 Replies View Relatedlaptop access (via wireless router) to program data resident on my PC. The subject program is installed (frequently updated) on my PC (Windows XP). Laptop (also Windows XP) use of this data for viewing and printing is the objective -- without also installing the program on the laptop. (The catch is frequent updates.)
Both units have access to broadband; direct for PC and wireless router for the laptop. Have no problem also installing program on laptop, if needed: laptop access to current data is the issue. Even doing so via internet would be great. It seems that LAN and Broadband networks are both in play though I don't quite grasp any inherent conflicts.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel(R) Pentium(R) 4 CPU 2.80GHz, x86 Family 15 Model 2 Stepping 9
[Code].....
I regularly perform updates on servers and this normally requires a reboot. I would like to be able to inform my customers when the server is back ASAP. Is there a program that continuously tries to remote to the server until it does or is there a script I can add to the server to send me notification of when the server ia back up?
View 2 Replies View RelatedLet me start by saying i know pirating is wrong. Dont tell me i shouldn't do it. I download TV shows so i can watch them when i want.Okay, With the Six Strikes Program set to start this week. Major ISP's like AT&T and time Warner are going to start sending you stuff when you download torrents. And throttling your bandwidth after so many times.
View 2 Replies View Relatedi want to connect two computers to run the same program, they are conneted to a router and both have internet. i doing this for tax season and i want them to run the same program and have the same information on them.
View 5 Replies View RelatedMy friend is trying to open port 88 and it says this specific message "The specified ports are being used by other configurations".I did a netstat, netstat -a, and another netstat that i forgot and we could find anything on his computer using port 88.His router is a Netgear wndr3400.
View 5 Replies View RelatedI need to know if PC Anywhere will work for the IMac and if not, what is the equivalent remote access program for the IMac?
View 1 Replies View RelatedI want to force a certain program (Max Payne 3) to use the third and forth DNS's that I configured in advanced settings of DNS settings (Windows7).
I want to do this because for some reason, using Google DNS in Turkey makes the game not start forcing me to use the DNS servers of my Internet provider. (if only it tried the second DNS that I configured, it would start but for some reason it does not)
Is their a program i can use to see who is doing what then disable their monitor keyboard and mouse. I work for my college/student and i am the assistant admin, my teacher gave me full admin privileges. I would like to have this as untended program where they cant change any thing stays hidden in the back ground. I used team viewer but i have to have them to log each one.
View 2 Replies View RelatedI was recently asked by a friend working for a new ISP in my city about managing their bandwidth, honestly I couldn't give him any answer.
View 6 Replies View RelatedMy school forces me to install an enterprise security program in order to connect to their network and get online. Its very bloated, and i can't edit the settings, they make it scan my computer everyday and so on.I want to use my OWN security program which i bought (norton).Is there any way to work around this requirement to get online on their network?
View 2 Replies View RelatedI have a program Eric's Movie Data Base. It needs to go to IMDB to update very often.On my XP there is no problem, it connects quickly every timeHowever I need to run it on my laptop with vista with a wireless connection.Using Vista the program EMDB runs ok but cannot connect to the IMDB site via the program.I have checked and firewall is off, and UAC also.As xp has no problem ( both are usin the same router) I can only assume Vista is blocking it.The request is reaching my modem, and the router is not using any port forwarding.Error message in log isFIREWALL replay check (1 of 24): Protocol: ICMP Src ip: 94.64.148.77 Dst ip: 58.166.25.196 Type: Destination Unreachable Code: Port UnreacheableI have contacted the developer who says the program is using the IE engine.
View 14 Replies View RelatedI have 2 programs located and running of 2 different servers (both server 2003)due to the nature of the company I work for I cannot say what the progams are. Now how our network is set up is Program 1 runs and server 1 and program 2 runs on server 2. server 1 and 2 and all user pc's are connected to a domain run by server 3. The programs 1+2 are installed on user computers and connected to thier respective servers to run. now the problem is program 1 kicks a random number of users off everyday at 10:15AM and program 2 does the same but at 12:45. its the same time and its every day. I have checked all servers for errors or conectivity issues and have found nothing.
View 4 Replies View RelatedI heard that the belkin n750 was good for gaming, but i cant seem to connect with 5ghz which i believe is alot faster than 2.5ghz, but yeah i would like to know how to configure my router to improve my game speed and performance.
View 3 Replies View RelatedLost CD used to download program and website is not facilitating in resetting password.....
View 2 Replies View Relatedi just got a used cisco 877 from ebay, the router i got not reponding to ping, and not picking up adsl signal, i ask the seller for a refund, the seller told me i must use aux cable to program, i had a cisco 857, which can be program through ethernet on default setting. is cisco 877 a lot different than 857?
View 1 Replies View RelatedI would like to know how I can split bandwidth between 4 work floors that have different needs. I have a network switch that can be managed (Cisco) but am not sure how I can set this up.
View 1 Replies View RelatedIm looking for tool that wud manage nsf files on network...
View 1 Replies View RelatedWe have a dir-615 in our ong.We would like giving different permission to the users.I want that users can connect only to the ong network and other user may use internet.Today i don't know hou to do. I can block intretrnet access (with child control), but not for only selected user.
View 1 Replies View RelatedIs it safe to manage an 891 router across the Internet using Cisco Configuration Professional 2.4? If so, a few pointers on enabling and configuring it. If not, I assume setting up a VPN to the router then using CCP across the VPN would be the preferred approach.
View 1 Replies View RelatedWe have just replaced a 4507R for a 4507R-E but I can't RME to manage it. I also can't get Cisco View to work. We appear to have packages installed (see attachments).
Is there anything I can do to troubleshoot?
I have setup WCS logins to be managed by ACS 4.2 . I was looking over the docs and I appear to be missing something because I can't find any documentation on doing the same to the controllers. I did successfully lock myself out of the WiSM in the lab during some testing. I had to pull the plug on the lab ACS to allow local login.
View 6 Replies View Related