I have setup WCS logins to be managed by ACS 4.2 . I was looking over the docs and I appear to be missing something because I can't find any documentation on doing the same to the controllers. I did successfully lock myself out of the WiSM in the lab during some testing. I had to pull the plug on the lab ACS to allow local login.
View 6 RepliesWhat is the benefit of having multiple Domain Controllers on a WAN
View 1 Replies View RelatedI have been tasked by my boss of finding out and implementing a solution of building GRE tunnels from 2 4408 Wireless controllers system for a guest wireless network. I am but a low CCNA wireless, working on getting motivated for CCNP wireless, but I didn't even know if this was possible and if it was where to begin. I have been reading configuration guides but figure I should ask the wireless experts of the world of Cisco.
View 7 Replies View RelatedOur controller get freezing every week at least twice, and do not know what is the reason. I am attaching the log for you to look at it. Last time happened was yesterday at around 13.00 pm.
View 15 Replies View RelatedIn need to upgrade the software on two WLC 4402 controller in a hospital. Both WLCs have the same config and one is primary (has all APs connected) and the other backup (no APs connected.) The APs are placed so there is still coverage if one goes down in an area. My question - is it possible to do a rolling upgrade to have no downtime for the wireless clients? My plan would be to upgrade the backup WLC then selectively move APs to it. If I swap the primary and secondary controllers in the high availability tab on each AP, do I need to do a reset (General - Hardware Reset) or will it automatically reboot and connect to the upgraded backup controller? When I'm done, I'd upgrade the primary controller and now call that backup. Does this make sense?
View 4 Replies View RelatedWe need to rename our 4404 Wireless LAN Controllers. Would like to know if renaming via the GUI (change name in the Controller / General tab and then Apply) will cause the WLC to reload. Also wondering about the best way to push the name change to the APs (High Availability) - we are not using WCS.
View 5 Replies View RelatedQ: a client has a network with 60 AP's controlled by a AIR-CT5508-50-K9 (+ L-LIC-CT5508-25A) with a redundant power supply. Can he get full redundancy by purchasing a second controller? If he purchases one, can he bring it into the network? What about the extra license for 25 extra AP's installed on the first controller?
View 4 Replies View RelatedI am read this cisco document Cisco Catalyst 3850 Switch Services Guide
[URL]...
which describe that
L2 roam occurs when the user roams from an access point connected to its controller to a different access point connected to another controller, where the two controllers are L2 adjacent to each other.
L3 roam occurs when the user roams from an access point connected to its controller to a different access point connected to another controller, where the two controllers are L3 adjacent to each other.
so what exactly this mean the two controllers are L2/L3 adjacent to each other , what is the different between them.
I would like to upgrade our three WLC 4402 controllers from version 7.0.116.0 to 7.0.235.3. I have downloaded the two files (AIR-WLC4400-K9-7-0-235-3-ER.aes and AIR-WLC4400-K9-7-0-235-3.aes). Which one should I upgrade/install first?
View 4 Replies View RelatedCurrently in the process of migrating from psk to 802.1x radius environment using a mix of 4400 and 5508 controllers with WCS using Microsoft ias. The problem I have is there is a lot of shared iPads and tablets in the environment. Is there a way to force these user to relogin to radius after a certain time period so they are not sharing unames and passwords?
View 1 Replies View RelatedWe have 7206 VXR running NPE-G1, we are looking for the GigE cards for 7200 which supports upto line rate and came across Cisco 7200 Series Input/Output Controllers The datasheet for the same doesnt say anything about line rates.
View 3 Replies View RelatedI am configuring two 2504 controllers, which I ordered together, however they run different software versions and I don't have a contract/ login to download wlan controller software from the Cisco website. The one with the newest version runs 7.2.103.0 while the other one runs 7.0.220.0 I want to run them together in the same subnet and use them for redundancy (10 AP's will connect).
Is there a way I can download the software from the controller, just like I am able to do with an ASA firewall? Then I can upload it to the controller with the older software version.
Please find attached a simple BYOD/ISE document I uploaded to kick start my new Wireless setup. Its all configured on my ISE sever and Controller as per doc.My setup:
-3600 AP's
-Internal 5508 Controller
-DMZ 5508 Controller (acts as a DHCP server for wireless clients)
Controllers have established connectivity (mobility acnhors), as a client I can connect fine to my new SSID get a DHCP IP address back from DMZ WLC and at the moment can connect out to the Internet fine (using no WLAN Security as a test). So this part is working.I have now followed the document configured ISE, enabled AAA on the Internal WLC only and used the AAA override setting on WLAN as in the attached document.I connect to SSID expecting to be redirected to my ISE Guest Portal, nothing happens other than connecting to Internet WebPages.My question is, if I have followed this document correctly why is the Internal WLC not redirecting client requests to ISE, is this because my mobility anchors need to be re-configured, perhaps the AAA/ISE config needs to be applied to my DMZ WLC not internal WLC?
I would prefer the Internal WLC to redirect the login to ISE, doesn't make sense to traverse through the DMZ Firewall onto DMZ WLC back into the Internal Network again to the ISE to authenticate.Or am I missing something additionally to this document to make sure clients are directed to the ISE Guest portal login.
We are in the earlier stages of moving our Domain Controlllers from 2003 to 2008 R2. The remote agents are running in 2003 Domain Controllers. According with Cisco Documentation, I can move the agent to a Windows 2003 Member Server and the upgrade to 2008 R2 Domain Controllers.
View 4 Replies View RelatedI am setting up two 5508 controllers, one in HA mode, and one the primary for the remote sites in question. I plan to have these units service wireless for MPLS conected regional sites (each with their own local subnet). I was planning on using the cabled hosts network in each site for the wifi addressing and was thinking a different addressing for Guest Access, is this common? I'm obviously concerned with guest access clients but don't know enough how their trafiic is segregated from normal wifi traffic.
Also, when I stand up the controllers the management interface and ap-manager won't be in the same network as where the hosts or LWAP's will reside (routing access will exist though).
We have 2 Cisco 5508 WLCs, each wtih 50 licenses. What I would like to do is split the 50 odd APs between the 2 controllers load balancing the traffic. If a controller goes down or there is a break in the path all APs would failover to their configured secondary controller. So far so good.
However there seems to be no way to 'replicate' the configurations between controllers unless I setup HA , but as I understand it HA is Active /Passive, so essentially, unless you get a failover situaltion, completely 'redundant'.
Is there a way or either replicating between controllers automatically with out HA, or is there a way of making HA Active / Active?
We have two 4400 controllers which support 50 Access points each and wcs with 100 base license.Now we added 5508 controller supports 50 access points.wcs is upgraded with another 50 ap license.The 5508 controller is joined to wcs and the licence showing permanent.WCS showing all aps and showing both 100 and 50 licence as permanent.But the issue is while loging into the wcs it showing the error message as"The system is in violation of license.The number of APs registered is greater then licensed."
View 5 Replies View RelatedI have two 5508 and one WCS server, the controllers are in one mobility group.Now I have to change the management IP addresses on the controllers. What are the correct steps to do this?
View 9 Replies View Relatedim unable to create pri-group under T1 controllers in 2651xm , I have 3 T1 VWIC controller cards [dual port], tried using differnt IOS [advance enterprise/IPVoice/SPservices], i can onyl see channel-group unter the controllers.
network-clock-particiapte slot 1
network-clock-participate wic 0
i havent added "isdn switch type", does addign these command enables the Pri-group, also wheni do sh inv, i see 3 pvdms, but no serail number,
I'm looking into upgrading our 4400 series controller to 5508's. Currently we have a few sites that have 8-9 4404 100AP controllers and I'm looking to condense these down to either 3 5508-500 or 5 5508-250 depending on cost. I'm wondering what a good port to AP ratio is for controllers with licenses that can handle over 100 AP's. I know the general rule of thumb is 25 AP's per port, but that seems to me to be 4400 way of thinking. I'm trying to also reduce the controllers overall footprint, i.e. ports on the uplink switch, power consumption, rack space etc.
View 5 Replies View RelatedI am planning to move our WLC's (5508) from a branch site to HQ so that all branch site APs will just report centrally in the HQ. There are two WLCs working as Active/Standby. Plan is to move one then the other. I am not really inclined with wireless.
View 9 Replies View RelatedActually we have a 4402 controller with 1120 APs both of which are marked as EoL products, we want to jump over the new 2600 APs and 5508 Controller for increase signal coverage but we have the following deals:Last firmware for 4402 controller is 7.0.Firmware needed for 5508 to support 2600 APs is 7.3.Is it possible to configure mobility between 4402 and 5508 even with different firmware branch?
View 3 Replies View Related--- I have 2 WLC's 5500 that I have to set up on my network with the same configuration except I am not sure that they can be load balanced.
-- My only thought is to take a full class C and on each WLC set up a /25, thus each device can provision 120 IP's
--- This seems a bit archaeic, but is there anything else smarter to do? Can they be load balanced?
We are installing a set of 5508 controllers at one site in Tennessee. At another divisional site we have another controller that covers that division.
Both sites utilize the same DNS structure and would like to use the DNS entry CISCO- CAPWAP- CONTROLLER entry for bringing new AP onto the controllers at their sites, how would we go about configuring this?
I am working in an environment with 6 4402 all running 6.0.119.4 code and WCS 6.0.196.0. I keep getting an alert from WCS that the controllers cannot be reached "Controller '10.x.x.x' is unreachable. - Controller Name: 'Name'"
Now when I go to access the WLC through HTTPS I have no access at all but controller still responds to ICMP, HTTP, Telnet, SSH. I know I should have HTTP and Telnet disabled but since HTTPS keeps failing I would have no way to get into the controller. Is this a known issue in the 6.0.199.4 code? should I consider upgrading? The only fix I have found to work is to disable HTTPS reboot controller enable HTTPS and reboot again.
If we have 2 Cisco 2504 series wlcs and use multicast features in both and both are primary and secondary for LAPs. what about of we use multicast ip address let's say 255.239.1.60 can we use the same ip address for the secondary controller too or we should use any other ip ?
View 7 Replies View Relatedthat big network has DHCP server which give ip addresses to clients and manage their internet.in one of this companies because of security matters they set up a domain network for themselves .problem is this if they use main DHCP their systems get ip in form of 172.16.58.x and boot up slowly it takes about 3 min to network indicator appears near clock and also they get into problem when ever they want to add a shared printer.but if they get ip address from DHCP and set that ip address and subnet mast and gateway manually the same as main DHCP server and only change dns server to theirs DC controller ip address every thing will work properly .but problem is they must set their ip addresses automatically.that is DHCP ip address sample
172.16.58.23
255.255.255.0
172.16.58.1
dns=172.16.1.1 & 172.16.1.2
see 172.16.58 is ip range of this company on that big network
in one of the sites, the client has an exisiting 4402 controller which he moved to the DMZ in order to set it as an anchor & he purchased two new 5508 controllers to control the corporate APs. I configured all the parameters needed for the guest anchoring & then I tested the connection but there was an issue. (all the controllers are running the same firmware version)after testing the setup, the guest users could get an IP from the internal DHCP of the anchor controller (in DMZ), but then they cannot reach the internet or anything outside the anchor controller.Cisco confirmed that the 4400 is fully compatible with the 5500 to work in an anchor-foreign secnario as long as they are running the same firmware version. yet, when I temporarily used one of the 5500 controller in the DMZ as an anchor & I applied the exact same configurations on it as the 4400, it worked perfectly without any issues.
note: on the anchor controller (4400), the management & AP-manager interfaces reside on the same subnet & the wireless guest SSID is also mapped to the management interface. (may be this setup is causing the issue) but on the 5500 it is working just fine?
I have 2 WLAN controllers, a 4400 series and 5500 series controller. The 4400 series has 100 seat limit on it, with 74 Access Points currently connected. The 5500 series has a 250 max, but we bought it with only 50 licenses, and it is max'd out at 50.The 5500 controller is the controller that has a DNS entry so that the Access Points will know to find that controller as they're being added. BUT, because we've reached our limit of 50 licenses, I'd like to be able to set the 4400 series controller to be the controller that new Access Points try to connect to. By going back to the 4400 as the controller that new Access Points connect to buys me time to plan for more licenses on next years budget for the 5500 controller.
View 29 Replies View RelatedEvery time I power down my WLC2504 controller and then back up, the time reverts back to the year 2000.The APs can't join the controller, due to certificate errors, until I reset the clock. This problem just started recently.
View 6 Replies View RelatedHaving performance issues running two 5508 controllers on the same network? One is running 7.3.101.0, the other is running 7.0.98.0. The legacy APs are connected to the WLC on the older code to support older hardware. The new WLC is accepting all the new 3600 APs. Once all legacy APs are replaced, the 5508 on old code will be disabled.
View 3 Replies View RelatedI want to download the Cisco 2500 Series Wireless Controllers Release 7.3 Software AIR-CT2500-K9-7-3-112-0.aes.I have CON-SMB for it, when I try to download it I am not to download it. I have mentioned the message given by Cisco" The category for this contract does not include the feature or the benefit for software download that you are requesting at the moment, this means that even if the contract is a support assistant (8X5XNBD) does not support the the mentioned feature for you to update the device you need, please refer to your partner directly to be able to acquired a Cisco Service Contract that supports and include the software download feature to be able to upgrade and update your device as you need."Is there any seprate contract for downloading the Software.
View 2 Replies View RelatedDoes 2500 series wireless controllers support redundancy?
View 1 Replies View Related