We have 7206 VXR running NPE-G1, we are looking for the GigE cards for 7200 which supports upto line rate and came across Cisco 7200 Series Input/Output Controllers The datasheet for the same doesnt say anything about line rates.
View 3 RepliesI have this topology in part of my networ:k
Cisco7200---Cisco6500---Cisco3560---LAN1
|
Cisco3560
|
LAN2
All devices are interconected via optical 1Gb/s links. There is no QoS implemented on any device and all VLANs are allowed on all interfaces.
Also all links are trunks (with many VLANs)
In LAN1 there was a layer 2 broadcast-storm and 4000packets/s was comming to rest of the network (in one particular VLAN).
1) 7200 with G1 should be able to handle traffic up to 500Mb/s, but a lot of users experienced drops on traffic via 7200.
(CPU load was around 10%).
2) Why do I have input drops on 7200 on link toward 6500 if CPU was normal. Broadcast comming to this interfaces were cca 4kpps. But since it's destination is not on router these packets should be rejected on interface controller. Is that right? (7200 doesn't even has dot1q subinterface in that VLAN but since 6500 allow all VLANs on its trunk these packets reach 7200)
3) Why do I have output drops on Cisco 6500 (it is here as layer 2 device only)? It is max 160Mb/s in output direction. It has WS6724 card with DFC (there is no oversubscription).. Shouln't 6500 send traffic as fast as interface allows (up to 1Gb/s). Am I righ't?
4) After all how coul'd 6500 now if 7200 can't handle these traffic?Output drops should be only seen if QoS is enabled (i.e. shaping), or if there is oversubscription on the linecard?
My router, a Cisco 7204 with NPE 300, is experiencing output drops and input errors on a fastethernet interface. I have a 100Mbps connection with less than 15Mbps utilization at peak times.
FastEthernet1/0 is up, line protocol is up Hardware is DEC21140, address is 0014.a985.1a1c (bia 0014.a985.1a1c) Internet address is 38.102.66.134/30 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 3/255, rxload 1/255
[Code]....
I found increasing of total output drops and output queue drops even input rate was low and no qos apply on this interface. I plan to increase hold queue out for output queue.
Router 1941, 15.0(1)M4
Serial0/0/0 is up, line protocol is up
Hardware is WIC MBRD Serial
[Code]....
Sometimes our network lag and i thing there is a computer making this problem. i'd like to audit all input output of all port of a Catalyst 1900. all i manage to do is to enter to the console menu via Telnet.. once here, i try monitoring but i'm afraid to do a bad thing :
Catalyst 1900 - Main Menu
[C] Console Settings
[S] System
[N] Network Management
[P] Port Configuration
[Code]...
I recently configured a network with a 4500 Sup7E and a 3560G with jumbo frame support. I am trying to confirm operation. On the 4500 this is straight forward using "sho int g0/nn count detail". [code] The 3560 doesn't support that command. The closest I can come to finding the number of jumbo packets is "show controllers ethernet" (example below). On the transmit side I assume that jumbo frames would be tallied in the "Too large frames" counter. The receive side is a little more ambiguous. There are 2 counters that seem to be duplicates, "Valid frames, too large" and "Valid oversize frames". In operation they are not. I am seeing the "Valid frames, too large" counter incrementing while the "Valid oversize frames" remains at zero. [code]
View 0 Replies View RelatedI have too much output drops in my cisco 7206 VxR NPE G1 router. I'm doing dot1Q on this interface and is connected to switch , i changed the router and IOS but still the error is same . What can be the reason . The interface on switch and router are 1000/Full and i changed the cable also . The traffic only comes about max70Mbps and it is really confusing. [code]
View 9 Replies View Relatedwhen i type "show interface" command on 1941 router, shows below print. Why 5 minute input-output rate are 0 bits? Can it be a bug?
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
304015 packets input, 151607798 bytes, 0 no buffer
[Code].....
when using egress netflow (v9) and output marking.
The topologie : Server <-----> R1 1>-----<1 R2 2>----<2 R3
R2 is a 7200 with c7200p-adventerprisek9-mz.124-15.T11.bin What I'm doing :- R2 forwards ping packets from Server to R3. When they arrive on R2, icmp packets are marked with CS3
- I change the DSCP to CS4 on R2 before forwarding packet to R3. I'm using for that an output service-policy on the R2-2 interface like this : interface ATM2/0.36 point-to-point
ip address 192.168.1.1 255.255.255.252
ip flow ingress
ip flow egress
[Code]....
I have a video feed coming into my 3570. It comes in at 5 minute input rate 18777000 bits/sec, 1695 packets/sec. However, the uplink to the router is much different, 5 minute output rate 130000 bits/sec, 28 packets/sec. I am in a lab and about ready to go into testing phase for a project when we discovered this problem, as this video feed is not veiwable on the other end.
Below is the config and capture from the switch.
BLOSSw1#sh int g1/0/6GigabitEthernet1/0/6 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is a44c.112f.3506 (bia a44c.112f.3506) MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 4/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters 15:16:25 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute
[code]....
On my SUP-7E, when I issue a " show interface vlan X " I cannot see the expected input/rate reflecting the real rate (which should be very high).
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 4000 bits/sec, 2 packets/sec
(Under the physical interfaces it is ok)However on other SUP-IV I can see the real rate.
My questions are :
- Why the SUP-7E does not reflect the rate, whereas the SUP-IV does ?
- I have heard about the 'counter' command under the vlan interface to activate the rate counters. Is this command application has any side effect on the switch ?
I have made some test and i noticed that qos input policy does not classify the icmp packet based on their dscp.The "match dscp ef" or "match precedence 5" is not working only the "match protocol icmp" shows hits.
We need to classify the different icmp packets based on dscp ( TOS ) for measurement purpose.CISCO 7200, 12.4.25d and 12.4.20T have a same behavior.
Our customer get the problem that the switch count the 5mins input/output rate of connected traffic interface always ZERO.The problem only occur in the module 3,4 and 5 interface, module 2 has no problems.
-------------------------------------------------------------------------------------------------
Catayst 4506E
12.2(52)SG
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E 2 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 3 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 4 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 5 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E
[code]....+
I want to download the Cisco 2500 Series Wireless Controllers Release 7.3 Software AIR-CT2500-K9-7-3-112-0.aes.I have CON-SMB for it, when I try to download it I am not to download it. I have mentioned the message given by Cisco" The category for this contract does not include the feature or the benefit for software download that you are requesting at the moment, this means that even if the contract is a support assistant (8X5XNBD) does not support the the mentioned feature for you to update the device you need, please refer to your partner directly to be able to acquired a Cisco Service Contract that supports and include the software download feature to be able to upgrade and update your device as you need."Is there any seprate contract for downloading the Software.
View 2 Replies View RelatedDoes 2500 series wireless controllers support redundancy?
View 1 Replies View Relatedwhat does VXR and S means in these series?
View 1 Replies View RelatedWhat are the rough figures that a NPE-G2 is able to hold for the BGP routing table?
378475 network entries using 51472600 bytes of memory 378482 path entries using 21194992 bytes of memory 63008/63003 BGP path/bestpath attribute entries using 8065024 bytes of memory BGP using 82975730 total bytes of memory
Are these 3 memories different memory allocated or are they are a sub-set of each other? If a NPE-G2 has 1GB RAM, does it mean that the routing table limit is depending on the RAM availability?
One of my customer is looking for 1 port OC3 card for 7200 series router. There are two options (PA-POS-2OC3/PA-A6-OC3)However my customer is not sure whether he wants a ATM/POS card.
How to determine whether i should go for ATM or POS Card for OC3. Or atleast what should be my approach to determine whether i should go for ATM or POS Card for OC3.
What is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedI have setup WCS logins to be managed by ACS 4.2 . I was looking over the docs and I appear to be missing something because I can't find any documentation on doing the same to the controllers. I did successfully lock myself out of the WiSM in the lab during some testing. I had to pull the plug on the lab ACS to allow local login.
View 6 Replies View RelatedWhat is the benefit of having multiple Domain Controllers on a WAN
View 1 Replies View RelatedI have been tasked by my boss of finding out and implementing a solution of building GRE tunnels from 2 4408 Wireless controllers system for a guest wireless network. I am but a low CCNA wireless, working on getting motivated for CCNP wireless, but I didn't even know if this was possible and if it was where to begin. I have been reading configuration guides but figure I should ask the wireless experts of the world of Cisco.
View 7 Replies View RelatedOur controller get freezing every week at least twice, and do not know what is the reason. I am attaching the log for you to look at it. Last time happened was yesterday at around 13.00 pm.
View 15 Replies View RelatedIn need to upgrade the software on two WLC 4402 controller in a hospital. Both WLCs have the same config and one is primary (has all APs connected) and the other backup (no APs connected.) The APs are placed so there is still coverage if one goes down in an area. My question - is it possible to do a rolling upgrade to have no downtime for the wireless clients? My plan would be to upgrade the backup WLC then selectively move APs to it. If I swap the primary and secondary controllers in the high availability tab on each AP, do I need to do a reset (General - Hardware Reset) or will it automatically reboot and connect to the upgraded backup controller? When I'm done, I'd upgrade the primary controller and now call that backup. Does this make sense?
View 4 Replies View RelatedWe need to rename our 4404 Wireless LAN Controllers. Would like to know if renaming via the GUI (change name in the Controller / General tab and then Apply) will cause the WLC to reload. Also wondering about the best way to push the name change to the APs (High Availability) - we are not using WCS.
View 5 Replies View RelatedQ: a client has a network with 60 AP's controlled by a AIR-CT5508-50-K9 (+ L-LIC-CT5508-25A) with a redundant power supply. Can he get full redundancy by purchasing a second controller? If he purchases one, can he bring it into the network? What about the extra license for 25 extra AP's installed on the first controller?
View 4 Replies View RelatedI am read this cisco document Cisco Catalyst 3850 Switch Services Guide
[URL]...
which describe that
L2 roam occurs when the user roams from an access point connected to its controller to a different access point connected to another controller, where the two controllers are L2 adjacent to each other.
L3 roam occurs when the user roams from an access point connected to its controller to a different access point connected to another controller, where the two controllers are L3 adjacent to each other.
so what exactly this mean the two controllers are L2/L3 adjacent to each other , what is the different between them.
I would like to upgrade our three WLC 4402 controllers from version 7.0.116.0 to 7.0.235.3. I have downloaded the two files (AIR-WLC4400-K9-7-0-235-3-ER.aes and AIR-WLC4400-K9-7-0-235-3.aes). Which one should I upgrade/install first?
View 4 Replies View Related