Cisco WAN :: 7200 Series NPE-G2 BGP Routing Table?
Jul 2, 2012
What are the rough figures that a NPE-G2 is able to hold for the BGP routing table?
378475 network entries using 51472600 bytes of memory 378482 path entries using 21194992 bytes of memory 63008/63003 BGP path/bestpath attribute entries using 8065024 bytes of memory BGP using 82975730 total bytes of memory
Are these 3 memories different memory allocated or are they are a sub-set of each other? If a NPE-G2 has 1GB RAM, does it mean that the routing table limit is depending on the RAM availability?
View 1 Replies
ADVERTISEMENT
Feb 1, 2012
What is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
View 1 Replies
View Related
May 26, 2013
What is the size of the routing table in the 800 series?
View 1 Replies
View Related
Apr 28, 2012
I am little confused about the location of FIB table and adjacency table in both cisco 6500 series and fixed ports switches .In case of 6500 series switches
"Central CEF mode:The CEF FIB and adjacency tables reside on the route processor,and the route processor performs the express forwarding. Use this CEF mode when line cards are not available for CEF switching, or when features are not compatible with distributed CEF."
If line cards do no support CEF, then FIB and adjacency tables are built and are located on route processor( control plane ). Data plane operations are implemented in software and route processor performs those operations.
Some Cisco switches actually use different hardware to control the different planes. For example, the Cisco Catalyst 6500 is a modular switch that uses the Multilayer Switch.Feature Card (MSFC) for control-plane operations, and the supervisor Policy Feature Card (PFC) for the data-plane operations.
Supervisor module has has MSFC and PFC. MSFC implements control plane operation where as PFC implements data plane operation.But the first paragraph says in Central cef mode, both data plane and control plane operations are implemented by route processor. [code]
Do these switches implement the Central mode cef in same way as mentioned above. i.e
"Central CEF mode:The CEF FIB and adjacency tables reside on the route processor and the route processor performs the express forwarding. Use this CEF mode whenline cards are not available for CEF switching, or when features are not compatible with distributed CEF."Or fixed ports switches such as 3750 implement data plane operation in hardware where FIB tabe and adjacency table are maintained on Data plane.
View 3 Replies
View Related
Feb 26, 2011
what does VXR and S means in these series?
View 1 Replies
View Related
Sep 12, 2012
One of my customer is looking for 1 port OC3 card for 7200 series router. There are two options (PA-POS-2OC3/PA-A6-OC3)However my customer is not sure whether he wants a ATM/POS card.
How to determine whether i should go for ATM or POS Card for OC3. Or atleast what should be my approach to determine whether i should go for ATM or POS Card for OC3.
View 4 Replies
View Related
Mar 22, 2012
We have 7206 VXR running NPE-G1, we are looking for the GigE cards for 7200 which supports upto line rate and came across Cisco 7200 Series Input/Output Controllers The datasheet for the same doesnt say anything about line rates.
View 3 Replies
View Related
Jan 16, 2013
In datasheet of WS-SUP720-3B - link- was said that are only supported around 256K routes (fib?rib?).With this value I can't get 2 full bgp - that is around 850K ..
The supervisor is that control this or just memory ? I said this because I have a 7204-npe-g1 whith 2 fullrouting and 1G of and he are ok..
View 3 Replies
View Related
Dec 27, 2012
recently i removed the squid cache from the 7200 router so that i could apply the Qos on the router my topology is simple i have 7200 with two working interfaces
GI0/1====>LAN
Gi0/3====>to isp and working bgp
have 550 Mega BW from isp . at the rush hour , the quality of browsing becomes worse .i just need a Qos to apply it on the 7200 router so that the priority for my traffic as follow:
1- browsing has the highest priority
2-youtube has the 2nd priority after browsing
3-download & other applications have the 3nd priority.
View 8 Replies
View Related
Jul 30, 2012
I am experiecing issues with HSRP.I have two 7200 core routers connected via one portchannel layer 2 and i set up the HSRP.The switch 01 is the master and 02 is the bkp.the problem is, the bkp router can´t see the master and there are a lot of loggs with active-speak and can´t see the master. the configuration are ok, i just check and recheck but there are no mistakes. [code] the configurations are ok, but the router can´t see each other, just in the vlan 500 the other vlans are ok.
View 7 Replies
View Related
Apr 26, 2013
i want to ask , how to match youtube in my qos, i want to give youtube the best priority in the rush hour. currently im using an acl that match the ips of youtube but i think its not sufficeitt :
View 5 Replies
View Related
Jul 23, 2012
router 7200 (12.2(33)SRE1)
two interfaces with traffic going through, placed in a Data-VRF
Another physical interface and loopback interface in the global routing-table.
ip flow ingress on all physical interfaces configured
It was running for at least a year: I was getting netflow packets on my analyzer from the box. Since a couple of weeks I get no netflow-packets anymore.debug ip flow export tells me "IPFLOW: Sending export pak to ... port 2055"
But the packet is not leaving the box. By setting up an ip sla monitor udp-echo I simulated some traffic (udp/2055) which is leaving the box.
[code]...
View 2 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Jan 31, 2012
I tried the "Advanced Routing" Feature over the RV-042 V3 Dual WAN VPN Router , And the New IP Subnet i added ( 10.0.7.0 ) in the Static Routing Table does NOT Appear in the Routing Table of the Router. Please review the attached Print Screen for both the Static Routing Entry Configuration & the Routing Table of the RV-042 Router.
View 0 Replies
View Related
Dec 5, 2012
I started using RIPv2 on Packet Tracer. I got two subnets to connect with two routers. After I completed that, I decided to add a third router. How to setup the Routing Table for atleast R3 ?
View 5 Replies
View Related
Oct 2, 2012
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies
View Related
Nov 14, 2012
We have small which I'm looking to implement and have built this on GNS3.
We have:
Router A in site 1
Router B in site 2
Router C in site 3
Router A and B are connection via a point to point 100M link and from Router C we have a 2 point to point one of which is 5Mpbs and going to Router A and Router B.
For Router C to reach Router A network it will go via Router B and these are 100M connection. When the link between Router A and B goes down. Router C should update and start using the 5m route.
For some reson, the routes are not updating. I have to do 'clea ip eigrp ne' for the routes to update and if I reload the routers all works well, it seems the problem is intermittent.
View 13 Replies
View Related
May 22, 2013
I am attempting to filter a specific host(s) from my OSPF routiing table on a ASA 5550 (ABR) using LSA prefix lists. However, when I look at the other routers in that area, I notice that ALL LSA type-3's are being removed (10 hosts are now missing from the routing table). I have verified the filter is working on the ABR, but I can't figure why ALL hosts/routes that were coming into the area are now being filtered instead of the specific one that I want to filter out.
Here is the config on the ABR:
prefix-list pdm_pl_000 seq 10 permit 206.253.180.137/32
!
!
router ospf 1
network 10.0.0.0 255.255.255.0 area 0
network 10.150.10.0 255.255.255.0 area 10
network 10.150.252.0 255.255.255.224 area 10
[code]....
The 206.253.180.137 host is actually coming from Area '3'. Am I doing something that is removing all type-3 LSA's?
View 3 Replies
View Related
Apr 17, 2012
I have voice Bandwidth on Cisco Router 7200 and catalyst 3750.Now i want to sell some BW ( 15MB ) to any cleint. How to do that .We have Ethernet connectivity with my cleint.How i restrict client to 15MB. Will i have to form any VLAn or just port limit with bandwidth and which is better way?
View 8 Replies
View Related
Mar 13, 2012
I have too much output drops in my cisco 7206 VxR NPE G1 router. I'm doing dot1Q on this interface and is connected to switch , i changed the router and IOS but still the error is same . What can be the reason . The interface on switch and router are 1000/Full and i changed the cable also . The traffic only comes about max70Mbps and it is really confusing. [code]
View 9 Replies
View Related
May 28, 2011
I'm learning about iptables, but I don't fully understand the chains of NAT table (prerouting, postrouting and output).I'm specially in doubt about prerouting and postrouting. As far as I know, DNAT can be made with prerouting and SNAT can be made with postrouting, so I think prerouting is for input and postrouting is for output, but the material I'm reading (and another sources) are not clear.
View 4 Replies
View Related
Feb 4, 2013
We have a BGP / OSPF configuration as shown in the topology picture. When the connection towards Internet is taken down, we expect the traffic to be forwarded toward WAN 2 (preferred) or WAN 1. The problem is that the BGP learned routes disappears when the Internet connection is taken down. The IP routing table on R2 only shows internal networks and the networks between R2 and WAN 1 and 2. No routes to internet is shown. We run "show ip bgp neighbors <ip-to-wan-1-router> received-routes" it contain internet routes. And when we run "show ip bgp neighbors <ip-to-wan-1-router> routes" it contains no routes at all.
View 2 Replies
View Related
Dec 8, 2012
I have this routing table which I need to fill in for the network shown in the image attached. guide me to some good resources to understand
View 1 Replies
View Related
Apr 2, 2013
viewtopic.php?f=33&t=24000
How can you remove these "L" routes in routing table?
View 6 Replies
View Related
Feb 22, 2011
Which data structure used to preparation of a routing table.
View 6 Replies
View Related
May 9, 2012
I am currently using 2 routers. One is a 2wire router with stock firmware it is connecting to the internet and can't be altered all too much, it also has a PC connected to it. The other is a WRT54GL with Tomato on it with pretty much EVERY other PC and device connected to it, it is also connected to the 2wire and DMZ'd through it.What I want to do is somehow allow everything on the Tomato router to have access to the 2wire router's PC. (For media access or printers or whatever on Windows 7)
View 13 Replies
View Related
Dec 20, 2011
I have made some test and i noticed that qos input policy does not classify the icmp packet based on their dscp.The "match dscp ef" or "match precedence 5" is not working only the "match protocol icmp" shows hits.
We need to classify the different icmp packets based on dscp ( TOS ) for measurement purpose.CISCO 7200, 12.4.25d and 12.4.20T have a same behavior.
View 6 Replies
View Related
Nov 27, 2012
Is there a Table which the list the route table entries on Cisco ISR Router especially ISR 1921 Router.
View 3 Replies
View Related
Feb 6, 2013
On the 6509, with normal 67xx cards installed, where is all the mac table held, is it held on the card itself or on the supervisor? And if I use dcef cards, I gather the MSFC copies the mac table to the DFC ?
View 1 Replies
View Related
Jan 11, 2012
Cisco 1812, Version 12.3(8)YI1..What does "none" mean ?Most of mac adressess in cam has specified interface, but several has none.
View 12 Replies
View Related
Jul 7, 2012
I know its probably got something to do with EIGRP no auto-summary, I was wondering if I could get some input as to why a route would change from being variably subnetted, which is usually the case until no auto-summary is deployed. Or am I totally lost? I attached a screen shot for a closer observation.
View 1 Replies
View Related
Feb 19, 2012
I am in need to have the arp table cleared every 5 seconds or so on a 2800 router. I was wondering how I might be able to accomplish this.
View 4 Replies
View Related
Jul 23, 2012
My 2821 router has an arp table with the wrong ip to Mac mappings. The impact is that I can reach any host in the 10.1.1.1 subnet. I can reach hosts in the 192.168.35.0 just fine. [code] It is as if the 192.168.35.1 device is answering all arp requests as a proxy arp or something. Clear arp-cache nor clear ip arp on my 2821 have any affect.
View 1 Replies
View Related
