One of my customer is looking for 1 port OC3 card for 7200 series router. There are two options (PA-POS-2OC3/PA-A6-OC3)However my customer is not sure whether he wants a ATM/POS card.
How to determine whether i should go for ATM or POS Card for OC3. Or atleast what should be my approach to determine whether i should go for ATM or POS Card for OC3.
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View Relatedwhat does VXR and S means in these series?
View 1 Replies View RelatedWhat are the rough figures that a NPE-G2 is able to hold for the BGP routing table?
378475 network entries using 51472600 bytes of memory 378482 path entries using 21194992 bytes of memory 63008/63003 BGP path/bestpath attribute entries using 8065024 bytes of memory BGP using 82975730 total bytes of memory
Are these 3 memories different memory allocated or are they are a sub-set of each other? If a NPE-G2 has 1GB RAM, does it mean that the routing table limit is depending on the RAM availability?
We have 7206 VXR running NPE-G1, we are looking for the GigE cards for 7200 which supports upto line rate and came across Cisco 7200 Series Input/Output Controllers The datasheet for the same doesnt say anything about line rates.
View 3 Replies View RelatedWhat is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
Is there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point? There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.
View 1 Replies View Relatedusually when I get a card that throws this error I assume it is dead however I just want to verify that I am not missing something[CODE]
View 2 Replies View RelatedCan I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies View RelatedI have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedOSPF-4-ERRRCV: Received invalid packet: Bad LLS Checksum with one of our tunnels
View 1 Replies View RelatedMy company has a spare 7200 VXR, originally planned to be placed on our TDM network. This plan was not followed through, but I'd like to switch it's function to work as a core router on our BGP network. I'd like for this 7200 to be able to handle full routes from our eBGP peer, something the SUP module in my 6500 isn't capable of doing. What kind of SUP module should i look at replacing this 7200 VXR with?
View 5 Replies View Relatedhow many GRE tunnels (without IPSEC) can 7206 router supported. I have low bandwidth 2000 links & i want to configure GRE tunnels for them.
View 1 Replies View RelatedI have 7200 Router some flows are not forwarded and when i check ""show ip cache flow"" output i found the destination interface is going to Null i checked the access-list it permits these flows.
View 3 Replies View RelatedI have on 7200 series router with NPE-G1 module which is facing high CPU utilization. I have not found any particular process causing this high CPU utilization as it is caused due to interrupts. I have already enabled fast switching by "ip cef" command. Please suggest how to normalize the utilization as it is impacting the network and causing slowness. Please find below the output of show process cpu and also find attached the show tech of the device. Also let me know if any other output is required.
[CODE]...
We are running ISP and now a days we have many spam in our network, we want block the SMTP port 25 block on Cisco router 7200. So we can block the spam in our network.
View 3 Replies View RelatedI am having some issues with creating an ACL for my gateway router.I want to block external access to my network 192.168.1.0/24 from internet so i set up the ACL on the WAN port of my 7200 router asI am using named extened access list -
{
deny ip any 192.168.1.0 0.0.0.255 log
permit ip any any
}
and i applied this inbound accesslist on the WAN port of router as
"ip access-group acl-in in"
Now i have blocked the external traffic to my network 192.168.1.0/24 but the issue i am having is i am also unable to reach outside now. All i want is to block external traffic on the router WAN port but allow internal traffic to outside. Did i miss anything in the access list?
I am experiecing issues with HSRP.I have two 7200 core routers connected via one portchannel layer 2 and i set up the HSRP.The switch 01 is the master and 02 is the bkp.the problem is, the bkp router can´t see the master and there are a lot of loggs with active-speak and can´t see the master. the configuration are ok, i just check and recheck but there are no mistakes. [code] the configurations are ok, but the router can´t see each other, just in the vlan 500 the other vlans are ok.
View 7 Replies View RelatedI am facing a problem when configuring the ipsec vpn on my 7200 router. [code]
View 5 Replies View RelatedI am getting the following message while trying to configure WCCP redirection on my 7200 router.
I have added this router to the routerlist of the WAE edge device. Ping is successful, but the following problem prevails.
NASCM-MPLS#show ip wccp
Global WCCP information:
Router information:
[Code]....
I have a CAB-OCT-V35-FC cable in my Cisco 7200 router and not all of them are utilized. I have to connect another site with a point to point leased line and I am planning to use one of the ports in my Cisco 7200 router which is using the CAB-OCT-V35-FC cable. My problem is both the cable end and the modem is V.35 female connector and both are DCE. I need to build a crossover cable of V.35 male to male which will connect the Cisco 7200 router and the modem.
View 2 Replies View Related7200 VXR router got rebooted after due software crash dump.I have replaced NPE-G1 but still router is rebooting. Currently I am running with 12.4 (15)T 13 IOS.Crash Dump file is attached.
View 4 Replies View RelatedHow do I upgrade the boot rom version on the 7200 router? I am running IOS Version 12.4(22)T and when I plug in the serial ds3 card in my router it keeps rebooting with a watch dog error ( see below). Also, what version should I upgrade to?
Router#sh verCisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Fri 10-Oct-08 10:10 by prod_rel_team
ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router uptime is 0 minutesSystem returned to ROM by power-onSystem image file is "sup-slot0:/c7200-spservicesk9-mz.124-22.T.bin"
[code]....
why my router will not synchronize with an NTP server located an off-site facility; the NTP server is located at the Naval Observatory. I have a Cisco 7200 VXR IOS 12.4 The clock and calendar both are set correctly.
View 2 Replies View RelatedI have a E4200 router, and I had previously plugged in a small external hard drive just to test the functionality. The router seemed to recognize the storage, and the computers on the network could see it as a shared drive. Now I have plugged in a Seagate 7200 internal hard drive inside a Rocketfish enclosure, but the router is not recognizing anything. I just upgraded the firmware to 1.0.04, but there was no change. Are there problems using an enclosure rather than just plugging in an external hard drive?
View 1 Replies View RelatedCan Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedI have created a VPN site to site tunnel between Pix and Router. I have pix in my control but router is under Client control. I have done everthing I need to do but I am getting errors.
When I run sh isakmp sa , I get .
Total : 1
Embryonic : 0
dst src state pending created
x.x.x.x x.x.x.x QM_IDLE 0 0
When I run sh ipsec sa , I get...
local ident (addr/mask/prot/port): (10.0.0.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (x.x.x.x/255.255.255.255/0/0)
current_peer: x.x.x.x:0
PERMIT, flags={origin_is_acl,}
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
[code].....
I want to use chanelized POS PA in 7200 router. I want to know can I use chanelized PA for both chanelized and non-chanelized OC3/STM1? Does the both chanelized and non-chanelized feature is supported on chanelized module or I have to use other module?
View 1 Replies View RelatedI ran across this today on a 7200 that when all the vty lines are filled, and dont release, you enter clear line vty x and it is supposed to release the line. Well in some versions it doesn't work.
Here is the work around I found. clear tcp line vty x
I want to monitor my 7200's CPU packets per second rate.Any command i can run to show this?Or any MIB so I can poll this? 7200 NPE-G1 can handle 1mpps. And i want to verify the actual rate.
View 1 Replies View Related